Search results for "ibers"
showing 10 items of 578 documents
Third-harmonic generation in optical microfibers: From silica experiments to highly nonlinear glass prospects
2012
International audience; Using optical microfibers, phase matching between different propagation modes allows for third-harmonic generation (THG). After detailing the relevant phase matching conditions and overlap integrals, we provide a comparison between THG effective efficiencies in silica and tellurite glasses. We also explain the relatively easy, wideband, conversion that we observe experimentally in silica glass microfibers, from 155 mu m to the green, by the geometry of the tapering region.
Reinforcement Efficiency of Cellulose Microfibers for the Tensile Stiffness and Strength of Rigid Low-Density Polyurethane Foams
2020
Rigid low-density closed-cell polyurethane (PU) foams are widely used in both thermal insulation and structural applications. The sustainability of PU foam production can be increased by using bio-based components and fillers that ensure both enhanced mechanical properties and higher renewable material content. Such bio-based foams were produced using polyols derived from rapeseed oil and microcrystalline cellulose (MCC) fibers as filler. The effect of MCC fiber loading of up to 10 wt % on the morphology, tensile stiffness, and strength of foams has been evaluated. For estimation of the mechanical reinforcement efficiency of foams, a model allowing for the partial alignment of filler fibers…
Black Bioinks from Superstructured Carbonized Lignin Particles
2023
A renewable source of carbon black is introduced by the processing of lignin from agro-forestry residues. Lignin side streams are converted into spherical particles by direct aerosolization followed by carbonization. The obtained submicron black carbon is combined with cellulose nanofibers, which act as a binder and rheology modifier, resulting in a new type of colloidal bioink. The bioinks are tested in handwriting and direct ink writing. After consolidation, the black bioinks display total light reflectance (%R) at least three times lower than commercial black inks (reduction from 12 to 4%R). A loading of up to 20% of nanofibers positively affects the cohesion of the dried bioink (1 to 16…
Characterization of a fiber-reinforced new fully aromatic liquid crystalline polymer
1998
A new rigid liquid crystalline polymer that demonstrates good mechanical and thermomechanical properties and acceptable processing temperature has been recently synthesized and characterized. The melting temperature and some thermomechanical properties do not seem, however, suitable for use in some applications at high temperature or in the presence of aggressive fluids. The use of appropriate inorganic fillers can overcome these shortcomings. In this work the new LCP, polymerized in a bench-scale apparatus, and the same sample filled with carbon fibers are characterized. The properties of the carbon fiber filled LCP are compared with those of another filled wholly aromatic commercial LCP,…
Compatibilization of blends of polyethylene with a semirigid liquid crystalline polymer by PE-g-LCP copolymers
1997
The blends of thermoplastics with liquid crystalline polymers show, in general, poor properties because of the lack of adherence between the two phases. The use of ad hoc synthesized copolymers containing the monomer units of the two polymers has been recently considered by some of us for blend compatibilization, and the results appear promising. In this work, new PE-g-LCP copolymers, prepared either by the synthesis of the LCP in the presence of a functionalized PE, or by reactive blending of the latter polymer with preformed LCP, have been employed as compatibilizing additives for blends of PE with a semirigid LCP. The morphology and the rheological and mechanical properties of the ternar…
Characterization of a fiber reinforced semirigid liquid crystalline polymer
1997
In this work, samples of a semirigid Liquid crystalline polymer reinforced with carbon and glass fibers has been characterized. Semirigid liquid crystalline polymers (LCPs) show some advantages with respect to rigid LCPs: in particular lower processing temperatures, and better compatibility with flexible thermoplastics, but also some disadvantages: lower mechanical properties and poor thermomechanical resistance. Both properties can be improved by adding inorganic fillers. Although elastic modulus and tensile strength of the glass fiber filled LCP improve remarkably with increasing the filler content, the same properties for the carbon fiber-filled samples do not increase with increasing ti…
Improving the properties of polypropylene–wood flour composites by utilization of maleated adhesion promoters
2007
Polymer composites filled with natural organic fillers have gained a significant interest during the last few years, because of several advantages they can offer compared with properties of inorganic-mineral fillers. However, these composites (based, in most cases, on polyolefins) often show a reduction in some mechanical properties. This is mainly due to the problems regarding dispersion of the polar filler particles in the non-polar polymer matrix and their interfacial adhesion with polymer chains. In this work, polypropylene-wood flour composites were prepared and the effect of the addition of a maleated polypropylene was investigated. The two materials were compounded by an industrial c…
Nonlinear beam self-cleaning in a coupled cavity composite laser based on multimode fiber
2017
International audience; We study a coupled cavity laser configuration where a passively Q-switched Nd:YAG microchip laser is combined with an extended cavity, including a doped multimode fiber. For appropriate coupling levels with the extended cavity, we observed that beam self-cleaning was induced in the multimode fiber thanks to nonlinear modal coupling, leading to a quasi-single mode laser output. In the regime of beam self-cleaning, laser pulse duration was reduced from 525 to 225 ps. We also observed a Q-switched mode-locked operation, where spatial self-cleaning was accompanied by far-detuned nonlinear frequency conversion in the active multimode fiber.
A New System for Choosing the Form and Size of Complete Denture Anterior Teeth
2016
Introduction: In the absence of pre-extraction records, the choice of the size an form of anterior complete denture teeth can be extremely subjective. Several clinical and statistical parameters are usually used for choosing the correct size and form of the complete denture anterior teeth. Clinical Innovation: The technique consists of a system that allows the dentist to choose and, if necessary, easily change the dental mold during maxillomandibular recording session. The unique feature of the system is that six teeth of each mold are represented by veneers, which are connected to each other on the lingual surface by a fiber that allows each veneer some degree of movement. Discussion: This…
Reacción emocional ante la exposición involuntaria a cibersexo en adolescentes: factores moduladores
2019
Los avances realizados durante los últimos años en el ámbito de las tecnologías de la información y comunicación han favorecido un uso generalizado de internet. La población adolescente utiliza Internet de forma natural y habitual para comunicarse, entretenerse y realizar tareas escolares. Si bien son múltiples los beneficios derivados del uso de internet, es necesario considerar que no está exento de riesgos como puede ser la exposición involuntaria (EI) a material sexual. Dadas las consecuencias que dicha exposición puede tener (sobre todo en edades tempranas), nuestro objetivo ha sido analizar las principales reacciones a nivel emocional durante la EI a material sexual, explorando posibl…