Search results for "interface"
showing 10 items of 2139 documents
Angular-resolved electron spectroscopy from (110) surfaces of ternary Ce-based intermetallics: CePd2Si2 and CeNi2Ge2
1997
Investigations of electronic properties were carried out for the ternary Ce-based intermetallic systems CeT2X2 (T = Ni, Pd; X = Ge, Si). To produce well-ordered and atomically clean surfaces, preparation is carried out in UHV. The polycrystalline substance was evaporated on a W(110) substrate with subsequent annealing. The single-crystalline layers obtained are characterised by MEED (thickness), AES (surface stoichiometry), LEED and SEM (surface structure). For electron-spectroscopic investigations, ARUPS (angle-resolved photoemission spectroscopy) was used. In the photoemission spectra, dispersion effects could be detected by variation of the detection angle.
Preparation by radio-frequency magnetron co-sputtering and characterization of thin films of lanthanum–strontium ferromanganites
2005
Abstract (La 0.8 Sr 0.2 )(Mn 1 − y Fe y )O 3 ± δ films with y = 0, 0.2, 0.5, 0.8 and 1, a few hundred nanometers thick, were deposited onto polycrystalline yttria-stabilized zirconia YSZ by a magnetron co-sputtering technique using individual targets of La 0.8 Sr 0.2 MnO 3 and La 0.8 Sr 0.2 FeO 3 . The deposition parameters, substrate temperature and gas pressure, were studied by scanning electron microscopy, energy dispersive X-ray spectrometry, X-ray diffraction and interferential microscopy for their effects on the morphological, chemical, topographic and crystallographic properties of films and YSZ-film interfaces. (La 0.8 Sr 0.2 )(Mn 1 − y Fe y )O 3 ± δ thin films were found to be …
Effect of the surface stoichiometry on the interaction of Mo with TiO2 (110)
2000
Abstract Molydenum has been deposited at room temperature on (110) TiO2 surfaces with different stoichiometries, roughnesses and crystallinities. Whatever the substrate preparation is, in-situ Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) studies as well as ex-situ atomic force microscopy (AFM) and reflexion high-energy electron diffraction (RHEED) studies reveal a Stranski–Krastanov growth mode: the completion of three monolayers followed by islands growth is observed in every case. The three monolayers are always composed of amorphous molybdenum oxide with an oxidation state of molybdenum less than IV. The oxidation of the molybdenum layers generates Ti3+ an…
Initial chemical transport of reducing elements and chemical reactions in oxide cathode base metal
2002
Abstract In the present work, the formation of compounds associated to the diffusion of reducing elements (Mg and Al) to the nickel surface of a one-piece oxide cathode has been studied. Those compounds have been evidenced after the annealing steps at high temperature performed on cathode base metal prior to the emitting coating deposition. Therefore, they form the “initial” interface between the nickel and the coating, in other words, the interface existing at the beginning of cathode life. Extensive analysis to characterize the nickel base prior to coating deposition has been performed by means of scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDX), …
An integrated approach to evaluating the tribo-contact for coated cutting inserts
2000
Abstract The orthogonal machining process when end turning medium carbon and austenitic stainless steels with cemented WC-Co tools coated with single-layer (TiC), two-layer (TiC/TiN), and three-layer (TiC/Al2O3/TiN) hard thin films was investigated. Extensive experimental investigations including the thermal, mechanical and tribological responses of the tribo-contact between the coating–substrate system and the chip, under different cutting conditions, were carried out. The study sheds light on the cutting forces, the interface temperatures and the tribo-contact conditions, including the friction energy dissipated at the tool–chip interface, the frictional heat flux conducting into either t…
The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process
2000
New knowledge about the tribological response deriving from the interaction of the substrate/coating-chip system, with special attention to the orthogonal cutting process when chatter-free end turning using natural contact tools, is developed. In order to evaluate the frictional behaviour of this process under modified contact conditions, experimental investigations including the contact temperature, the contact loads, friction and the frictional heat flux per unit area were carried out. In contrast to the most obvious approach, the coefficient of sliding friction versus the cutting speed, the contact temperature, the normal pressure and the interface control factor is considered. A number …
Microstructural evolution of wear-resistant FeCrB and FeCrNiCoB coating alloys during high-energy mechanical attrition
2008
Mechanical milling/attrition provides a convenient scope of simulating the microstructural changes encountered by wear-resistant coating alloys subjected to deformation under high frequency and high-intensity impact loading or accelerated wear condition. In the present study, the microstructural evolution of two commercial coating materials, FeCrB (Armacor M) and FeCrNiCoB (Armacor C), in the course of low- and high-intensity mechanical attrition, was monitored by X-ray diffraction and high-resolution transmission electron microscopy. While low-intensity milling leads to marginal grain refinement but no change in phase-aggregate in FeCrB, similar mechanical attrition causes boride precipita…
Influence of friction on the local mechanical and electrochemical behaviour of duplex stainless steels.
2006
International audience; The electrochemical behaviour of ferritic and austenitic phases in duplex stainless steel (UNS S32304) and the modifications induced by straining during sliding were studied by potentiodynamic polarisation curves determined at the microscale in a 1MNaCl (pH 3) solution, using an electrochemical microcell. The mechanical properties and stress state of each phase were determined by microhardness and X-ray microdiffraction measurements, before and after straining. The results show that sliding generates elastic straining of the ferrite and plastic deformation of the austenite. The electrochemical behaviour of these phases is dramatically altered, inducing a reduction of…
Oscillatory Changes of the Heterogeneous Reactive Layer Detected with the Motional Resistance during the Galvanostatic Deposition of Copper in Sulfur…
2015
Metallic copper was galvanostatically deposited on quartz|gold resonant electrodes by applying a constant current in a 0.5 M CuSO4/0.1 M H2SO4 aqueous solution. Galvanostatic copper deposition is one of the best methodologies to calibrate the electrochemical quartz crystal microbalances (EQCM), a gravimetric sensor to evaluate changes in mass during the electrochemical reactions through the Sauerbrey equation. The simultaneous measurement of mass, current density, and motional resistance by an EQCM with motional resistance monitoring allows us to characterize the processes occurring on the electrode surface and at the interfacial regions with unprecedented detail. During the galvanostatic c…
Manipulating Self-Avatar Body Dimensions in Virtual Worlds to Complement an Internet-Delivered Intervention to Increase Physical Activity in Overweig…
2020
Virtual reality has been found to be a useful tool for positively influencing relevant psychological variables in order to increase physical activity (PA), especially in the overweight population. This study investigates the use of avatars and their physical variations to extend the effectiveness of existing interventions to promote PA. The main objective is to analyze the influence of the avatars&rsquo