Search results for "inventio"
showing 10 items of 13031 documents
Laser Ultrasonics Inspection for Defect Evaluation on Train Wheel
2019
Abstract Passengers’ safety and in-service life of wheelset axles play an important role in railway vehicles. For this reason, periodic inspections are necessary. Among non-destructive techniques, ultrasonic ones are widely applied in this field. The main disadvantage of conventional ultrasonic techniques is that the overall inspection of wheels requires the train to be put out-of-service and disassembly each part, which is time-consuming and expensive. In this paper, a non-conventional non-contact laser ultrasonic inspection for train wheels is proposed. The proposed method uses a laser interferometer to receive the ultrasonic wave without contact. The receiving system allows choosing the …
New fine structures resolved at the ELNES Ti-L2,3 edge spectra of anatase and rutile: comparison between experiment and calculation.
2010
Abstract Anatase and rutile Ti- L 2,3 edge spectra were measured in electron energy loss spectroscopy (EELS) using a transmission electron microscope (TEM) coupled to a CEOS Cs-probe corrector, an omega-type monochromator and an in-column omega-type energy filter fully corrected for 2nd order aberrations. Thanks to the high energy resolution, high electron probe current and high stability achieved under this instrumental configuration, new fine structures, never reported before, were resolved at the L 3 band of both rutile and anatase. The data suggest that new peaks also exist in the L 2 e g band. The experimental spectra are compared with multichannel multiple scattering (MMS) calculation…
Key factors towards a high-quality additive manufacturing process with ABS material
2019
Abstract Additive Manufacturing technologies have gained a lot of popularity during the past years. The current challenge being the transition of this manufacturing technology from prototype oriented towards mass production. In order to achieve this, fabrication times and mechanical parameters must be improved. This paper aims to identify which are the parameters that have the highest influence on parts obtained with fused deposition modeling (FDM) technology from ABS material. In addition, this study identifies which are the most accurate methods to test the mechanical properties of FDM parts while still respecting ASTM standard for testing the tensile properties of plastics. It was found …
Binocular function measures as predictors of user performance in stereoscopic augmented reality
2021
Inconsistency between the binocular and focus cues in stereoscopic augmented reality overburdens the visual system leading to its stress. However, a high individual variability of tolerance for visual stress makes it difficult to predict and generalize the user gain associated with the implementation of alternative visualization technologies. In this study, we investigated the relationship between the binocular function and perceptual judgments in augmented reality. We assessed the task completion time and accuracy of perceptual distance matching depending on the consistency of binocular and focus cues in the stereoscopic environment of augmented reality. The head-mounted display was driven…
SIC based solid state protections switches for space applications
2017
Development and technology maturation of Silicon Carbide (SiC) power transistors over the last 15 years has motivated its study in aerospace systems. When compared with Si devices, superior voltage blocking capacity and the capability of operation at higher temperatures, give important advantages in space power electronics applications, similar to what happens in terrestrial electronics. This paper discusses the use of SiC power transistors for Solid State Power Switches especially addressed to the space segment. Two applications will be covered, the first is the Solid State Shunt Switch, widely used in high power Direct Energy Transfer (DET) photovoltaic power regulators and the second is …
Parasitic Bipolar Action in SiC Power MOSFETs Demonstrated by Two-Photon Laser Experiment
2018
A two-photon absorption technique is explored for Silicon carbide power MOSFETs and power junction barrier Schottky diodes using a pulsed laser. The similarities in design between the specific MOSFETs and diodes tested permit using mechanisms existing in the different structures as explanation for observed current variation with laser position. The diode shows variation in average current with change in laser depth only, whereas the MOSFET shows variation both with shifts in depth and shifts in position across the striped geometry of the device. The variation is explained to be due to bipolar amplification of the charge carriers generated in the MOSFET when a pulse focus includes a channel …
Electromagnetic and Thermal Modelling for Calculating Ageing Rate of Distribution Transformers
2018
Prediction of the lifetime for transformers is very important for maintenance and asset management. Finite element analysis was performed on a 5 MVA distribution transformers with aluminium foil-type windings and voltage rating 6600 V/23000 V. Electromagnetic modelling is implemented on the full three-phase transformer to calculate distributed losses, taking the skin effect into account. To reduce the computational burden, the distributed losses in one phase are used to analyse temperature rise in one phase of the transformer. The temperature rise results were used to determine the ageing rate of the transformer. Further, the influence of ambient temperature and cooling on the temperature r…
Explosive crystallization in amorphous CuTi thin films: a molecular dynamics study
2019
Abstract Molecular dynamic simulation was used to study mechanism of self-propagating waves of explosive crystallization (devitrification) in the CuTi metallic glass. Processes in thin rectangular samples composed of one to two million atoms were simulated and compared with experimental data. It was shown that the nucleation of primary crystalline clusters occurs homogeneously due to spontaneous fluctuations of atomic structure; the clusters not
A review on LiNixCo1−2xMnxO2 (0.1 ≤ x ≤ 0.33) cathode materials for rechargeable Li-ion batteries
2021
Abstract Electrochemical and physical properties of LiNixCo1−2xMnxO2 (0.1 ≤ x ≤ 0.33) electrode materials prepared by self-combustion were investigated. Pure LiNixCo1−2xMnxO2 (x = 0.1, 0.2, 0.33) materials with single phase and R-3 m layered structure were obtained as confirmed by X-ray diffraction. Energy Dispersive Spectroscopy, Scanning Electron Microscopy are commonly used to determine the chemical composition and the distribution of particle size of the three samples. The electrochemical performances of the samples were measured at different current rates in the 3–4.5 V potential range. The studied materials exhibit good discharge capacity. The magnetic susceptibility measurements and …
An anomalous wave formation at the Al/Cu interface during magnetic pulse welding
2020
This paper reports an anomalous wave formation at an Al/Cu bimetallic interface produced by magnetic pulse welding. The mechanism of the anomalous wave formation is investigated using both metallurgical characterization and the interface kinematics. It reveals that the anomalous wave is formed with the combination of the intermediate zone and the interdiffusion zone with a thickness of 70 nm, wherein the intermediate zone is caused by the local melting due to the high shear instability, and the interdiffusion zone is formed below the melting point of aluminum combined with ultrahigh heating and cooling rates of about 10^13 °C s^−1. A multiphysics simulation of impact welding has been perfor…