Search results for "komposiitit"
showing 10 items of 15 documents
Mechanical properties of natural fiber composites produced using dynamic sheet former
2018
Composites formed from wood fibers and man-made cellulosic fibers in PLA (polylactic acid) matrix, manufactured using sheet forming technique and hot pressing, are studied. The composites have very low density (due to high porosity) and rather good elastic modulus and tensile strength. As expected, these properties for the four types of wood fiber composites studied here improve with increasing weight fraction of fibers, even if porosity is also increasing. On the contrary, for man-made cellulosic fiber composites with circular fiber cross-section, the increasing fiber weight fraction (accompanied by increasing void content) has detrimental effect on stiffness and strength. The differences …
Parameter identification for heterogeneous materials by optimal control approach with flux cost functionals
2021
The paper deals with the identification of material parameters characterizing components in heterogeneous geocomposites provided that the interfaces separating different materials are known. We use the optimal control approach with flux type cost functionals. Since solutions to the respective state problems are not regular, in general, the original cost functionals are expressed in terms of integrals over the computational domain using the Green formula. We prove the existence of solutions to the optimal control problem and establish convergence results for appropriately defined discretizations. The rest of the paper is devoted to computational aspects, in particular how to handle high sens…
Biomass-based composite catalysts for catalytic wet peroxide oxidation of bisphenol A:preparation and characterization studies
2019
The wet granulation process was used to prepare new, efficient, and cost-effective granular biomass-based composite catalysts for catalytic wet peroxide oxidation (CWPO) of bisphenol A (BPA). The most stable composite granules was prepared by mixing biomass-based carbon residue (CR) with metakaolin (MK) combined with calcium oxide (CaO) or cement and a solvent (NaOH or KOH). For all the prepared composite granules, the optimized binding agents to carbon ratio was 0.3, the solvent to carbon ratio 1.2, and the agitation rate 1200 rpm. The specific surface area of the prepared catalysts was 152–205 m2/g. The composite granular catalyst (CR + MK + CaO + NaOH) had the most durable and stable str…
Effective elastic properties of biocomposites using 3D computational homogenization and X-ray microcomputed tomography
2021
A 3D computational homogenization method based on X-ray microcomputed tomography (μCT) was proposed and implemented to investigate how the fiber weight fraction, orthotropy and orientation distribution affect the effective elastic properties of regenerated cellulose fiber-polylactic acid (PLA) biocomposites. Three-dimensional microstructures reconstructed by means of the X-ray μCT were used as the representative volume elements (RVEs) and incorporated into the finite element solver within the computational homogenization framework. The present method used Euclidean bipartite matching technique so as to eliminate the generation of artificial periodic boundaries and use the in-situ solution d…
Impact of Si on the high-temperature oxidation of AlCr(Si)N coatings
2022
The resistance of wear protective coatings against oxidation is crucial for their use at high temperatures. Here, three nanocomposite AlCr(Si)N coatings with a fixed Al/Cr atomic ratio of 70/30 and a varying Si-content of 0 at.%, 2.5 at.% and 5 at.% were analyzed by differential scanning calorimetry, thermogravimetric analysis and X-ray in order to understand the oxidation behavior depending on their Si-content. Additionally, a partially oxidized AlCrSiN coating with 5 at.% Si on a sapphire substrate was studied across the coating thickness by depth-resolved cross-sectional X-ray nanodiffraction and scanning trans-mission electron microscopy to investigate the elemental composition, morphol…
Biomass-based composite catalysts for catalytic wet peroxide oxidation of bisphenol A : preparation and characterization studies
2019
Abstract The wet granulation process was used to prepare new, efficient, and cost-effective granular biomass-based composite catalysts for catalytic wet peroxide oxidation (CWPO) of bisphenol A (BPA). The most stable composite granules was prepared by mixing biomass-based carbon residue (CR) with metakaolin (MK) combined with calcium oxide (CaO) or cement and a solvent (NaOH or KOH). For all the prepared composite granules, the optimized binding agents to carbon ratio was 0.3, the solvent to carbon ratio 1.2, and the agitation rate 1200 rpm. The specific surface area of the prepared catalysts was 152–205 m2/g. The composite granular catalyst (CR + MK + CaO + NaOH) had the most durable and s…
Effects of particle clustering on the plastic deformation and damage initiation of particulate reinforced composite utilizing X-ray CT data and finit…
2018
In this paper, a new simulation technique which can include microstructural inhomogeneity of particulate reinforced composites is proposed to accurately study deformation pattern and damage mechanism in these composites. Three dimensional microstructures constructed from XCT images incorporated into finite element modeling codes with minimal approximation to capture the effects of cluster size, local volume fraction of particles in the cluster and the distance between clusters as relevant statistical quantities describing the microstructural inhomogeneity of particulate reinforced composites. A quantitative parameter as degree of clustering is defined to consider particle clustering effect.…
Conjugation with carbon nanotubes improves the performance of mesoporous silicon as Li-ion battery anode
2020
Carbon nanotubes can be utilized in several ways to enhance the performance of silicon-based anodes. In the present work, thermally carbonized mesoporous silicon (TCPSi) microparticles and single-walled carbon nanotubes (CNTs) are conjugated to create a hybrid material that performs as the Li-ion battery anode better than the physical mixture of TCPSi and CNTs. It is found out that the way the conjugation is done has an essential role in the performance of the anode. The conjugation should be made between negatively charged TCPSi and positively charged CNTs. Based on the electrochemical experiments it is concluded that the positive charges, i.e., excess amine groups of the hybrid material i…
Electrochemical properties of graphite/nylon electrodes additively manufactured by laser powder bed fusion
2023
Nowadays, additive manufacturing, known as 3D printing, is vigorously employed at various enterprises due to the ability of industrial series production and customization in conjunction with geometry freedom. While, material design and fabrication of composite materials, meeting the desired architecture and properties, is another promising application of additive manufacturing. For instance, additive manufacturing of the material exhibiting electrochemical properties is beneficial for the development of freestanding electrodes that might be used in electrochemical energy storage systems. Herein, the graphite/nylon composite with a high carbon ratio of 30 wt% was produced by laser powder bed…