Search results for "lamination"
showing 10 items of 123 documents
Moisture ingress in photovoltaic modules: A review
2021
Abstract Moisture ingress in photovoltaic (PV) modules is the core of most degradation mechanisms that lead to PV module power degradation. Moisture in EVA encapsulant can lead to metal grids corrosion, delamination and discolouration of encapsulants, potential induced degradation, optical and adhesion losses. The present work is a review of literature on the causes, effects, detection, and mitigation techniques of moisture ingress in PV modules. Literature highlights on determining the diffusivity, solubility, and permeability of polymeric components of PV modules via water vapour transmission rate tests, gravimetric, and immersion methods, have been presented. Electroluminescence, photolu…
A Numerical Study on Interlaminar Defects Characterization in Fibre Metal Laminates with Flying Laser Spot Thermography
2018
This work describes a numerical study on non-destructive evaluation of interlayer disbond defects in aerospace grade Fibre Metal Laminate sheets (FMLs). A recently proposed infrared non-destructive testing setup is considered, where a continuous laser is moved over the material surface, while the thermal footprint of the moving heat source is acquired, e.g. by an infrared thermal camera. Interlayer disbonds are then detected by analysing the features of the acquired thermograms. The experimental feasibility of this approach has been recently proved. The present work proposes a numerical simulation of the NDT approach, where the material thermal response is analysed and correlated to defects…
Effects of Nylon 6,6 Nanofibrous Mats on Thermal Properties and Delamination Behavior of High Performance CFRP Laminates
2014
none 8 no Nylon 6,6 electrospun nanofibrous membranes interleaved in Carbon Fibre Reinforced Plastic (CFRP) laminates have been proposed as a means to provide a higher threshold value to delamination on structural sites where composites are more prone to develop such failure. A model, highly crosslinked thus inherently brittle, epoxy matrix was selected for its high Young’s modulus and glass transition temperature exceeding 250 °C. The influence of the Nylon 6,6 nanofibres on the curing behaviour of the matrix and on the thermal and dynamic mechanical properties of the cured resin was investigated. These properties were related to the features of the epoxy resin and of the resin impregnated…
A mechanistic model on the role of “radially-running” collagen fibers on dissection properties of human ascending thoracic aorta.
2014
Aortic dissection (AoD) is a common condition that often leads to life-threatening cardiovascular emergency. From a biomechanics viewpoint, AoD involves failure of load-bearing microstructural components of the aortic wall, mainly elastin and collagen fibers. Delamination strength of the aortic wall depends on the load-bearing capacity and local micro-architecture of these fibers, which may vary with age, disease and aortic location. Therefore, quantifying the role of fiber micro-architecture on the delamination strength of the aortic wall may lead to improved understanding of AoD. We present an experimentally-driven modeling paradigm towards this goal. Specifically, we utilize collagen fib…
Numerical analysis of a piezoelectric structural health monitoring system for composite flange-skin delamination detection
2013
Abstract In this paper, a piezoelectric based Structural Health Monitoring (SHM) system is proposed to detect skin/stiffener debonding and delamination cracks proper of laminated composite structures. The SHM system is analyzed by means of a boundary element code implemented in the framework of piezoelectricity. The multidomain technique, coupled with an interface spring model, is used to model laminated composite structures as well as the bonding between the host delaminated structure and the piezoelectric sensor. Static sensitivity analyses are firstly performed on a drop-ply delaminated structure in order to identify a suitable configuration for the sensor. Then, the dynamic electromecha…
Model of delamination propagation in brittle-matrix composites under cyclic loading
2001
A model of interlaminar fatigue crack growth based on damage accumulation ahead of the crack is proposed. Linear cumulative assumption is used for damage estimation, and a quadratic failure criterion is applied for complex interlaminar loading. Model parameters are determined from mode I and mode II fatigue tests, and used to predict mixed-mode delamination propagation rate. Comparison of theoretical prediction with mixed-mode test results for different brittle graphite FRP at several mode- and load ratios show reasonable agreement.
Empirical model for stress ratio effect on fatigue delamination growth rate in composite laminates
2004
An empirical model is proposed for the stress ratio effect on the fatigue delamination growth rate in composite laminates under single-mode loading, intending to provide a simple and accurate description tool in engineering application. The model is based on heuristic considerations of damage accumulation ahead of the crack. Linear cumulative assumption is used for damage estimation. Comparison of the prediction based on the proposed model with the test results for different carbon, glass, and alumina fibre-reinforced composites at several stress ratios shows reasonable agreement.
A pulsed laser technique for an evaluation of the spall resistance of sputtered oxide films: diagnostic by interferometric probing
1998
Abstract A pulsed laser technique, based on conventional laser acoustics testing, has been developed to define the spall resistance of sputtered oxide films on a metallic target. Direct irradiation of the coated side of the sample generates an acoustic source at the inner film–metal interface. A model of the laser-induced epicentral displacements at the opposite side that takes into account the confining effect of the coating has been proposed to evaluate the critical laser irradiance corresponding to progressive damages at the inner film–metal interface, i.e. interface delamination, film spallation and film expulsion, respectively. The behavior of Al 2 O 3 and ZrO 2 films deposited by PVD …
Fatigue delamination experiments on GFRP and CFRP specimens under single and mixed fracture modes
2011
This paper deals with the experimental analysis of the delamination phenomena in composite materials under different loading conditions. Quasi-static and fatigue tests are performed on specimens made of glass-fibre (GFRP) and carbon-fibre (CFRP) reinforced plastic. In particular, experiments have been carried out under single fracture modes I and II (using standard DCB and ENF test configurations) and mixed modes I+II (using the MMB test configuration) with several mode mixtures. Results obtained for the two materials have been compared paying attention on the relationship between the parameters that describe the fatigue behaviour and the mode mixture acting during the crack propagation. © …
EXPERIMENTAL AND NUMERICAL EVALUATION OF THE MECHANICAL BEHAVIOUR OF GFRP SANDWICH PANELS
2007
This work deals with the analysis of the mechanical behaviour of a class of sandwich structures widely employed in marine constructions, constituted by fiber-glass laminate skins over PVC foam or polyester mat cores. In detail, a systematic experimental study and numerical simulations have shown that the theoretical prediction of the strength and the actual failure mechanism of these sandwich structures can be affected by significant errors, specially in the presence of prevalent shear loading. Moreover, because of the low shear stiffness and the elastic constants mismatch of the skins and core material, failure modes and strength are strongly influenced by eventual stresses orthogonal to t…