Search results for "laser"
showing 10 items of 3161 documents
Implementation of a double-scanning technique for studies of the Hanle effect in rubidium vapor
2007
We have studied the resonance fluorescence of a room-temperature rubidium vapor exited to the atomic 5P3/2 state (D2 line) by powerful single-frequency cw laser radiation (1.25 W/cm^2) in the presence of a magnetic field. In these studies, the slow, linear scanning of the laser frequency across the hyperfine transitions of the D2 line is combined with a fast linear scanning of the applied magnetic field, which allows us to record frequency-dependent Hanle resonances from all the groups of hyperfine transitions including V- and Lambda - type systems. Rate equations were used to simulate fluorescence signals for 85Rb due to circularly polarized exciting laser radiation with different mean fre…
Nonlinear Hanle effect in Cs vapor under strong laser excitation
2002
We report results of a theoretical and experimental study of the ground state nonlinear Hanle effect under strong laser excitation. It is shown that besides the well-known zero-magnetic field suppression of absorption on F g = F→F e = F - 1 transitions caused by population trapping, an optical pumping induced enhanced absorption occurs on F g = F→F e = F + 1 transitions for small B-fields. The latter effect becomes more pronounced for high F values. The experiment with atomic vapor of Cs (D2 line, F g = 4) confirms an increase of the spectrally unresolved fluorescence yield at zero magnetic field and 600 mW/cm2 laser intensity by 9% or 42%, when excitation occurs with linearly or circularly…
Analysis of powdered tungsten carbide hard-metal precursors and cemented compact tungsten carbides using laser-induced breakdown spectroscopy
2007
Laser-induced breakdown spectroscopy (LIBS) has been applied to the direct analysis of powdered tungsten carbide hard-metal precursors and cemented tungsten carbides. The aim of this work was to examine the possibility of quantitative determination of the niobium, titanium, tantalum and cobalt. The investigated samples were in the form of pellets, pressed with and without binder (powdered silver) and in the form of cemented tungsten carbides. Several lasers and detection systems were utilized.
Characterization of Fusion Lines Obtained with Laser Welding on Ductile Iron Plates
2016
This paper studies the ductile iron (DI) weldability using laser welding. For performing an Yb:YAG continuous laser was used, with a maximum power of 6 kW. The parametrical window power (P) - welding speed (S) was explored by carrying out the fusion lines on ductile iron plates without preheating, to determinate areas of weldability (complete penetration, correct geometry) to allow further characterization. The criteria for selection of focus areas were the geometry of the fusion lines and the absence of the welding defects. The unsatisfactory domains were characterized by: collapse of the melted metal, incomplete penetration, low fusion lines quality (geometry, compactness). In present stu…
Microstructure and property of titanium heterogeneous laser welding
2015
International audience; Dissimilar welding has been investigated for three different couples of titanium alloys: α/α+β, α/β and α+ββp. Plates of 100 x 60 x 1.6 or 1.8 mm were welded with a Yb: YAG laser. Tensile tests show that the properties of the dissimilar welded specimens were generally controlled by Those of the weakest material except for the α+β/β where the ultimate tensile strength was approximately equal to the average value of both materials. In every case, the welding sample elongation was found to be smaller than that of the base metals. The rupture took place away from the bead and was found to be always located in the alloy having the lowest mechanical properties. Nevertheles…
Infrared thermography for monitoring heat generation in a linear friction welding process of Ti6Al4V alloy
2017
Abstract The increasing use of titanium alloys in a wider range of applications requires the development of new techniques and processes capable to decrease production costs and manufacturing times. In this regard welding and other joining techniques play an important role. Today, solid state friction joining processes, such as friction stir welding, friction spot welding, inertia friction welding, continuous-drive friction welding and linear friction welding (LFW), represent promising methods for part manufacturing. They allow for joining at temperature essentially below the melting point of the base materials being joined, without the addition of filler metal. However, the knowledge of te…
Dissimilar laser welding of AISI 316L stainless steel to Ti6–Al4–6V alloy via pure vanadium interlayer
2015
Abstract Successful continuous laser joining of AISI 316L stainless steel with Ti6Al4V titanium alloy through pure vanadium interlayer has been performed. Three welding configurations were tested: one-pass welding involving all three materials and two pass and double spot welding involving creation of two melted zones separated by remaining solid vanadium. For the most relevant welds, the investigation of microstructure, phase content and mechanical properties has been carried out. In case of formation of a single melted zone, the insertion of steel elements into V-based solid solution embrittles the weld. In case of creation of two separated melted zones, the mechanical resistance of the j…
Hot cracking in Al–Mg–Si alloy laser welding – operating parameters and their effects
2005
Abstract Hot cracking is a phenomenon that frequently occurs in the laser welding of some “special” alloys, such as the aluminium–magnesium–silicon type. Each occurrence of this phenomenon needs to be studied in itself, taking into account not only the individual, but also the interactive, influences of the various parameters. The advantage of using laser beams in welding processes lies in the speeds that can be reached. The disadvantage, however, is that, owing to the high cooling rates characteristic of the interaction between the laser beam and the material, the welding speed itself becomes a cause of hot cracking. The aim of this paper is to see how this disadvantage may be eliminated. …
Gas protection optimization during Nd:YAG laser welding
2004
International audience; Many laser processes, such as welding or surface treatments are associated with an undesired phenomenon, which is oxidation. The solution commonly employed to solve this problem approaches the shielding gas and/or the shielding gas device. What we propose in this paper is a methodology with the goal to optimize the protection gas device design as well as the gas flow in the case of laser welding and surface treatments. The pressure created by the gas flow on the sample surface is recorded and analysed together with the operating parameters influence in order to reach the objectives. The nozzle system designed and presented below assures the protection against materia…
Friction Stir Knead Welding of steel aluminium butt joints
2008
To develop steel aluminium-tailored hybrids in a butt joint for sheets in a thickness of about 1 mm conventional Friction Stir Welding is not feasible due to a high distortion of the welded specimen. Contrary to Friction Stir Welding the tool used for Friction Stir Knead Welding has no pin wherefore higher welding speeds can be realised. Due to the fact that this is a newer process, applied for patent in 2005, the cut contours of the edges and their variations have to be optimised by numerical analysis to transfer a maximum of load in order to improve the formability. The examined materials in this paper are steel DC04, as well as the aluminium alloys AA5182 and AA6016 in sheet thicknesses …