Search results for "manufacturing"
showing 10 items of 2299 documents
Addressing Manufacturing Challenges with Cost-Efficient Fault Tolerant Routing
2010
The high-performance computing domain is enriching with the inclusion of Networks-on-chip (NoCs) as a key component of many-core (CMPs or MPSoCs) architectures. NoCs face the communication scalability challenge while meeting tight power, area and latency constraints. Designers must address new challenges that were not present before. Defective components, the enhancement of application-level parallelism or power-aware techniques may break topology regularity, thus, efficient routing becomes a challenge.In this paper, uLBDR (Universal Logic-Based Distributed Routing) is proposed as an efficient logic-based mechanism that adapts to any irregular topology derived from 2D meshes, being an alter…
Synergistic effect of fiber content and length on mechanical and water absorption behaviors of Phoenix sp. fiber-reinforced epoxy composites
2016
Phoenix sp. fiber-reinforced epoxy composites have been manufactured using compression molding technique. The effect of reinforcement volume content (0%, 10%, 20%, 30%, 40%, and 50%) and size (300 µm particles, 10 mm, 20 mm, and 30 mm fibers) on quasi-static and dynamic mechanical properties was investigated. Moreover, the water absorption properties of composites were analyzed at different environmental conditions (10℃, 30℃, and 60℃). For each reinforcement size, composites loaded with 40% in volume show highest tensile and flexural properties. Furthermore, composites with 300 µm particles present the best impact properties and the lowest water absorption, regardless of the environmental …
Optical study for springback prediction, thickness reduction and forces variations on single point incremental forming
2019
Abstract The goal of the present work is to present an experimental study regarding the influence of the main technological influence factors such as the vertical step and the punch diameter on the single point incremental forming process (SPIF). In this paper we estimate the influence of these two factors on springback, thickness reduction and forces. Both parameters were varied on two levels: (d) punch diameter 6 and 10 mm and (s) vertical step 0,1 and 0,5 mm. The experiments were done on experimental layout composed by a robot, a clamping system that contains the die’s lower part and the optical system.
Opening of New Synthetic Routes Using Segmented Microflow in Multistep Syntheses
2017
The application of microfluidics in organic chemistry is a valuable tool to access new synthesis pathways and to break limitations set by traditional batch chemistry. In the past, the majority of research focused on solving problems associated with individual reactions. It is necessary to advance the field by incorporating flow chemistry in longer multistep syntheses to open more direct paths towards complicated compounds. Several strategies were developed to meet the demands of a four-step synthesis, which includes biphasic nitrations, gaseous substrates, and very fast reactions on multifunctional molecules. A unique micro flow setup was applied in each reaction to meet its specific requir…
Estimating Missing Information by Cluster Analysis and Normalized Convolution
2018
International audience; Smart city deals with the improvement of their citizens' quality of life. Numerous ad-hoc sensors need to be deployed to know humans' activities as well as the conditions in which these actions take place. Even if these sensors are cheaper and cheaper, their installation and maintenance cost increases rapidly with their number. We propose a methodology to limit the number of sensors to deploy by using a standard clustering technique and the normalized convolution to estimate environmental information whereas sensors are actually missing. In spite of its simplicity, our methodology lets us provide accurate assesses.
Radiometric calibration of SeaWIFS in the near infrared
2005
The radiometric calibration of the Sea-Viewing Wide-Field-of-View Sensor (SeaWiFS) in the near infrared (band 8, centered on 865 nm) is evaluated by use of ground-based radiometer measurements of solar extinction and sky radiance in the Sun's principal plane at two sites, one located 13 km off Venice, Italy, and the other on the west coast of Lanai Island, Hawaii. The aerosol optical thickness determined from solar extinction is used in an iterative scheme to retrieve the pseudo aerosol phase function, i.e., the product of single-scattering albedo and phase function, in which sky radiance is corrected for multiple scattering effects. No assumption about the aerosol model is required. The ae…
Laboratory evaluation of falling-head infiltration for saturated soil hydraulic conductivity determination
2020
Falling-head one-dimensional infiltration procedures, such as the simplified falling-head (SFH) technique, yield estimates of saturated soil hydraulic conductivity, Ks, with parsimonious and rapid experiments. Factors that can influence determination of Ks by the SFH technique were tested in the laboratory on three repacked soils differing by particle diameter ranges (0-2000, 0- 105 and 105-2000 mm, respectively). Using the theoretically calculated depth of ponding on the infiltration surface, D, instead of the measured one had a small impact on the Ks calculations (means differing by a factor of 1.1-1.2, depending on the soil). For the finest soil, Ks decreased by 3.1 times as D increased …
Predicting plot soil loss by empirical and process-oriented approaches. A review
2018
Soil erosion directly affects the quality of the soil, its agricultural productivity and its biological diversity. Many mathematical models have been developed to estimate plot soil erosion at different temporal scales. At present, empirical soil loss equations and process-oriented models are considered as constituting a complementary suite of models to be chosen to meet the specific user need. In this paper, the Universal Soil Loss Equation and its revised versions are first reviewed. Selected methodologies developed to estimate the factors of the model with the aim to improve the soil loss estimate are described. Then the Water Erosion Prediction Project which represents a process-oriente…
Coping with the impacts of Urban Heat Islands A literature based study on understanding urban heat vulnerability and the need for resilience in citie…
2018
The urban heat island (UHI) is a phenomenon whereby temperature levels in urban areas are higher than in surrounding rural settings. Urban heat islands are a matter of increasing concern, since they can affect communities by exacerbating air pollution and greenhouse gas emissions (due to the greater use of air conditioning) and the occurrence of heat-related illness, and may lead to higher levels of mortality. This paper provides a description of the phenomena of (UHI) and an analysis of how cities are vulnerable to it. It highlights the need for resilience and the variety of means by which the UHI can be tackled. It describes a set of trends in two regions in Germany and Australia, which i…
Copper quality and sources in Middle Bronze Age I Byblos and Tell Arqa (Lebanon)
2013
Abstract Forty-four Middle Bronze Age I weapons discovered at the sites of Byblos and Tell Arqa in Lebanon were investigated in order to study their copper quality and provenance. The evaluation of copper qualities is based on quantifying permanent inclusions such as copper sulfide and lead globules. The provenance of copper was studied using lead isotope analyses. For further discrimination between copper groups and sources elemental analyses by PIXE were performed on some of the weapons investigated. The results revealed two copper groups that could be qualified as “dirty” copper and “clean” copper. The former was used in most of the weapon types whereas the latter was reserved for items …