Search results for "material"
showing 10 items of 32550 documents
Sewage sludge as cheap alternative to microalgae as feedstock of catalytic hydrothermal liquefaction processes
2019
Abstract Production of biocrude through hydrothermal liquefaction (HTL) of sewage sludge (SS) and Chlorella vulgaris was investigated. NiMo/Al2O3 (KF 851), CoMo/Al2O3 (KF 1022) and activated carbon felt, tested as catalysts at 598 K for 30 min, did not change the biocrude yield but significantly improved its quality. Quantitative sulfur removal and lower oxygen content were found in biocrude when KF 851 and KF 1022 were used with C. vulgaris. The same catalysts decreased O/C and S/C ratio of the biocrude from SS. The highest HHV (38.19 MJ/kg) and H/C ratio (1.65) and the lowest O/C (0.11) of the biocrude from SS were obtained with the cheaper activated carbon felt. A new product phase, prob…
Modelling IR Spectra of Sulfonated Polyether Ether Ketone (SPEEK) Membranes for Fuel Cells
2020
Authors acknowledge support from LSC project No 2014/666 ERDF and students ( ) support from project 2DP/2.1.1.1.0/14/APIA/VIAA/009.
From lab to industry: Scaling up green geopolymeric mortars manufacturing towards circular economy
2021
Abstract Construction is nowadays considered an extremely energy intensive industry and one of the main sources of environmental pollution in the world. Therefore, the research and the development of novel energy-saving manufacturing processes and sustainable construction materials is more than ever urgent and challenging. This paper aims at identifying the industrial process for the production of novel geopolymers to be used as a greener substitute for cement, especially the Portland one, widely used for structural applications to significantly reduce the environmental impact of the construction industry. Here, the materials sustainability and the manufacturing process are improved by valo…
Evaluating the material resource efficiency of secondary aluminium production: A Monte Carlo-based decision-support tool
2019
The contamination of aluminium streams during the different life cycle stages by alloy mixing and/or accumulation of foreign elements, in combination with the limited melt purification options during remelting, represents an important limiting factor in recycling. Consequently, in secondary aluminium production, primary aluminium is used to dilute the concentration of the residual elements, and alloying elements are added to adjust the composition to the target alloy specifications. However, adding elements, for which their refinement in a subsequent recycling step is problematic, results in permanent down-cycling or ‘quality losses’. Hence, it is crucial to more efficiently control the com…
Solar and Heat Pump Systems for Domestic Hot Water Production on a Small Island: The Case Study of Lampedusa
2020
The achievement of United Nations Sustainable Development Goals, related to energy and resource use, is a critical issue for small and insulated communities. In many minor islands, solar energy is not correctly exploited, and electrical heaters are connected to weak grids with very a high share of generation by fossil fuels. As a consequence, there is the necessity to assess the potential and the suitability of diffusion of alternative systems to avoid dependency on the electrical grid and reduce carbon emissions. This paper aims to evaluate the technical and economic performances of some alternative systems exploiting renewable energy for domestic hot water production. Four different syste…
Experimental Investigation into the Effect of Pyrolysis on Chemical Forms of Heavy Metals in Sewage Sludge Biochar (SSB), with Brief Ecological Risk …
2021
Experimental investigations were carried out to study the effect of pyrolysis temperature on the characteristics, structure and total heavy metal contents of sewage sludge biochar (SSB). The changes in chemical forms of the heavy metals (Zn, Cu, Cr, Ni, Pb and Cd) caused by pyrolysis were analyzed, and the potential ecological risk of heavy metals in biochar (SSB) was evaluated. The conversion of sewage sludge into biochar by pyrolysis reduced the H/C and O/C ratios considerably, resulting in stronger carbonization and a higher degree of aromatic condensation in biochar. Measurement results showed that the pH and specific surface area of biochar increased as the pyrolysis temperature increa…
Fast pyrolysis of hot-water-extracted and delignified silver birch (Betula pendula) sawdust by Py-GC/MS
2017
The thermochemical behavior of birch (Betula pendula) sawdust both untreated and after various chemical treatments (hot-water extraction, delignification, and hot-water extraction followed by delignification) was investigated by pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS). In each case, major GC-amenable condensable products were classified into several compound groups, and the formation of these monomer-related fragments from feedstock samples with varying mass portions of the structural constituents (cellulose, hemicelluloses, and lignin) were determined at 500 °C and 700 °C at hold times of 5 s and 20 s. The formation of pyrolysis products was shown to be characteristically…
Study about Mechanical Properties of Materials Obtained by Thermoforming
2019
Plastic materials have played a very important role in the development of our modern civilization. It can be said that plastic materials are a tribute to man’s creativity and inventiveness. Plastic materials are the key to the innovation of many products and technologies in various sectors such as electrical and electronic equipment, packaging, civil engineering, agriculture, power generation, medical and pharmaceutical industry, aerospace and not last automotive industry. An increasingly important aspect in the automotive industry, in terms of fuel consumption is the lower weight of the components, while maintaining a very high stiffness. The difficulties of the design process of thermofor…
Regarding the influence of the particle size of crumb rubber from waste rubber on the physical and mechanical characteristics of reclaimed rubber
2017
Thus, at present, a large amount of rubber waste cannot be higher harnessed due to recovery technologies used. Also, the requirements for new products of rubber worldwide are greater than the production capacity and the availability of raw materials. To offset this balance is necessary to improve technologies for recycling waste rubber so to can get regenerated rubber with the best mechanical physical characteristics. The main technology for obtaining the regenerated rubber is based on the rubber waste shredding and making the powder, so that it can be carried out de-vulcanization in autoclave. All the time it was monitored as the de-vulcanization process to be as economical and less pollut…
Definition of the thermographic regions of interest in cycling by using a factor analysis
2016
Abstract Research in exercise physiology using infrared thermography has increased in the last years. However, the definition of the Regions of Interest (ROIs) varies strongly between studies. Therefore, the aim of this study was to use a factor analysis approach to define highly correlated groups of thermographic ROIs during a cycling test. Factor analyses were performed based on the moment of measurement and on the variation of skin temperatures as a result of the cycling exercise. 19 male participants cycled during 45 min at 50% of their individual peak power output with a cadence of 90 rpm. Infrared thermography was used to measure skin temperatures in sixteen ROIs of the trunk and lowe…