Search results for "mechanical analysi"
showing 10 items of 96 documents
Characterizations of Thermoplastic Block Elastomers Based on Polybutadiene and ε -Caprolactone
2010
A broad series of tri- and multiblock copolymers based on linear and branched oligomers of polybutadiene as central blocks and polycaprolactone (PCL) as block extremities are characterized by SEC, DSC, DMA, Dynamical Rheology and DRX. DSC analyses reveal phase separation between the two amorphous PB and PCL phases. By thermal analysis, the glass transition temperature of PCL is only detected for materials containing at least 80% w/w of PCL. This is attributed to the small length of the polyester blocks for copolymers containing less than 80% w/w of PCL. The increase of fusion heat with increasing PCL content in the copolymers is correlated to the greater ability of PCL chains to rearrange a…
Long-term ISO 23936-2 sweet oil ageing of HNBR
2021
Abstract A hydrogenated nitrile butadiene rubber (HNBR) compound is subjected to ageing in a simulated oil and gas environment in accordance with ISO 23936-2 standard at two elevated temperatures (130 °C and 150 °C) for a period of up to 9 months. Shore D hardness, thermal expansion, dynamic mechanical analysis (DMA), Fourier transform infrared (FTIR) spectroscopy, compression and compression set (CS) measurements are made before and after the chemical exposure. The hardness, modulus at short times, degree of relaxation and CS increases while the coefficient of thermal expansion in HNBR tends to decrease with ageing time and temperature. Temperature is shown to impose a greater effect on th…
Dynamic mechanical properties of semi-interpenetrating networks based on poly(styrene-co-maleic anhydride): 3. Poly(2,6-dimethyl-1,4-phenylene ether)…
1994
Semi-IPN's based on linear poly(2,6-dimethyl-1,4-phenylene ether) (PPE) and diamine crosslinked poly(styrene-co-maleic anhydride) (PScoMA) copolymers containing small amounts of maleic anhydride (PSA=4.7wt.-% MA, PSB=5.8 wt-% MA) are studied with respect to the influence of cross-linking on the phase behavior. Temperature-dependent dynamic mechanical analysis (DMA) and DSC show that the semi-IPN's prepared from concentrated solution show weak crystallinity of the PPE phase. After heating above the PPE melting transition the semi-IPN's remain amorphous and the relaxation in the glass transition region as well as the terminal relaxation of the free PPE chains in the network is studied as a fu…
Material valorisation of amorphous polylactide. Influence of thermo-mechanical degradation on the morphology, segmental dynamics, thermal and mechani…
2012
[EN] This paper reports the effects of multiple mechanical recycling on the structure and properties of amorphous polylactide (PLA). The influence of the thermo-mechanical degradation induced by means of five successive injection cycles was initially addressed in terms of macroscopic mechanical properties and surface modification. A deeper inspection on the structure and morphology of PLA was associated to the thermal properties and viscoelastic behaviour. Although FT-IR analysis did not show significant changes in functional groups, a remarkable reduction in molar mass was found by viscometry. PLA remained amorphous throughout the reprocessing cycles, but the occurrence of a cold-crystalli…
Poly(styrene-b-methyl methacrylate) block copolymers as compatibilizing agents in blends of poly(styrene-co-acrylonitrile) and poly(2,6-dimethyl-1,4-…
1993
Abstract The influence of the molecular weight of the symmetric block copolymer poly(styrene-b-methyl methacrylate) (P(S-b-MMA)) in blends with high-molecular-weight poly(styrene-co-acrylonitrile) (PSAN) and poly(2,6-dimethyl-1,4-phenylene ether) (PPE) is investigated by dynamic mechanical analysis and transmission electron microscopy. Total molecular weights of the block copolymers vary from 16 up to 275 kg mol−1. Independent of molecular weight, all block copolymers locate to the interface with strong dispersing efficiency. The different block copolymers also showed approximately the same emulsifying efficiency. The degree of segmental mixing of the blocks with the respective phases is ev…
Rheology of a Lower Critical Solution Temperature Binary Polymer Blend in the Homogeneous, Phase-Separated, and Transitional Regimes
1996
Small amplitude oscillatory shear rheology is employed in order to investigate the linear viscoelastic behavior of the lower critical solution temperature blend polystyrene/poly(vinyl methyl ether), PS/PVME, as a function of temperature and composition. At low temperatures, where the mixture is homogeneous, the dependence of the zero shear viscosity (η0) on concentration is measured and is well-described by means of a new mixing rule, based on surface fractions instead of volume fractions. Shift factors from time-temperature superposition (TTS) exhibit a Williams−Landel−Ferry (WLF) behavior. As the macrophase separation temperature is approached (the phase diagram being established by turbi…
An Innovative Treatment Based on Sodium Citrate for Improving the Mechanical Performances of Flax Fiber Reinforced Composites
2021
The goal of this paper is to evaluate the effectiveness of a cost-effective and eco-friendly treatment based on the use of sodium citrate (Na3C6H5O7) on the mechanical properties of flax fiber reinforced composites. To this scope, flax fibers were soaked in mildly alkaline solutions of the sodium salt at different weight concentration (i.e., 5%, 10% and 20%) for 120 h at 25 °C. The modifications on fibers surface induced by the proposed treatment were evaluated through Fourier transform infrared analysis (FTIR), whereas scanning electron microscope (SEM) and helium pycnometer were used to obtain useful information about composites morphology. The effect of the concentration of the treating …
Thermomechanical Analysis of Isora Nanofibril Incorporated Polyethylene Nanocomposites
2021
The research on cellulose fiber-reinforced nanocomposites has increased by an unprecedented magnitude over the past few years due to its wide application range and low production cost. However, the incompatibility between cellulose and most thermoplastics has raised significant challenges in composite fabrication. This paper addresses the behavior of plasma-modified polyethylene (PE) reinforced with cellulose nanofibers extracted from isora plants (i.e., isora nanofibrils (INFs)). The crystallization kinetics of PE&ndash
Thermal and dynamic mechanical properties of beeswax-halloysite nanocomposites for consolidating waterlogged archaeological woods
2015
Abstract Thermal and mechanical properties were determined for the halloysite nanotubes (HNT)/beeswax composites at various compositions. The beeswax degradation temperatures and time course, provided by thermogravimetry (TG), evidenced the improvement of the thermal properties operated by HNT. Differential scanning calorimetry (DSC) allowed us to determine the enthalpy of melting as well as the time course of the melting process for beeswax. A slight loss of beeswax crystallinity was observed upon HNT addition. The dynamical mechanical analysis (DMA) provided the loss and the storage modulus for the nanocomposites upon heating and it was shown that the nanoclays create an inorganic framewo…
Cyclic moisture sorption and its effects on the thermomechanical properties of epoxy and epoxy/MWCNT nanocomposite
2019
The aim of this work was to reveal the moisture absorption&ndash