Search results for "mechanical"
showing 10 items of 5999 documents
Accelerated bearing life-Time test rig development for low speed data acquisition
2017
Condition monitoring plays an important role in rotating machinery to ensure reliability of the equipment, and to detect fault conditions at an early stage. Although health monitoring methodologies have been thoroughly developed for rotating machinery, low-speed conditions often pose a challenge due to the low signal-to-noise ratio. To this aim, sophisticated algorithms that reduce noise and highlight the bearing faults are necessary to accurately diagnose machines undergoing this condition. In the development phase, sensor data from a healthy and damaged bearing rotating at low-speed is required to verify the performance of such algorithms. A test rig for performing accelerated life-time t…
Fractional-Order System Identification of Viscoelastic Behavior: A Frequency Domain Based Experimental Study
2020
In this work, the fractional-order modeling of viscoelastic behavior is investigated based on measurement data in the frequency domain. For the results of two different test setups we apply existing parameter estimation algorithms designed for fractional-order transfer functions. These algorithms require a priori knowledge of the system structure including the commensurate order of differentiation. An iterative procedure is used to evaluate the influence of the unknown structure. The measured polymer samples show a viscoelastic stress response. We can show that integer-order models are not capable of capturing this behavior. For a set of predefined structures, the best obtained fractional-o…
Real-time biomechanical modeling of the liver using Machine Learning models trained on Finite Element Method simulations
2020
[EN] The development of accurate real-time models of the biomechanical behavior of different organs and tissues still poses a challenge in the field of biomechanical engineering. In the case of the liver, specifically, such a model would constitute a great leap forward in the implementation of complex applications such as surgical simulators, computed-assisted surgery or guided tumor irradiation. In this work, a relatively novel approach for developing such a model is presented. It consists in the use of a machine learning algorithm, which provides real-time inference, trained on tens of thousands of simulations of the biomechanical behavior of the liver carried out by the finite element me…
Smart sensing and adaptive reasoning for enabling industrial robots with interactive human-robot capabilities in dynamic environments — a case study
2019
Traditional industry is seeing an increasing demand for more autonomous and flexible manufacturing in unstructured settings, a shift away from the fixed, isolated workspaces where robots perform predefined actions repetitively. This work presents a case study in which a robotic manipulator, namely a KUKA KR90 R3100, is provided with smart sensing capabilities such as vision and adaptive reasoning for real-time collision avoidance and online path planning in dynamically-changing environments. A machine vision module based on low-cost cameras and color detection in the hue, saturation, value (HSV) space is developed to make the robot aware of its changing environment. Therefore, this vision a…
Relay feedback systems - established approaches and new perspectives for application
2019
Nivå1
Integrated GNSS/IMU Hub Motion Estimator for Offshore Wind Turbine Blade Installation
2019
Abstract Offshore wind turbines (OWTs) have become increasingly popular for their ability to harvest clean offshore wind energy. Bottom-fixed foundations are the most used foundation type. Because of its large diameter, the foundation is sensitive to wave loads. For typical manually assisted blade-mating operations, the decision to perform the mating operation is based on the relative distance and velocity between the blade root center and the hub, and in accordance with the weather window. Hence, monitoring the hub real-time position and velocity is necessary, whether the blade installation is conducted manually or automatically. In this study, we design a hub motion estimation algorithm f…
Ship-to-Ship State Observer Using Sensor Fusion and the Extended Kalman Filter
2019
In this paper, a solution for estimating the relative position and orientation between two ships in six degrees-of-freedom (6DOF) using sensor fusion and an extended Kalman filter (EKF) approach is presented. Two different sensor types, based on time-of-flight and inertial measurement principles, were combined to create a reliable and redundant estimate of the relative motion between the ships. An accurate and reliable relative motion estimate is expected to be a key enabler for future ship-to-ship operations, such as autonomous load transfer and handling. The proposed sensor fusion algorithm was tested with real sensors (two motion reference units (MRS) and a laser tracker) and an experime…
Anti-swing control of a hydraulic loader crane with a hanging load
2021
Abstract In this paper, anti-swing control for a hydraulic loader crane is presented. The difference between hydraulic and electric cranes are discussed to show the challenges associated with hydraulic actuation. The hanging load dynamics and relevant kinematics of the crane are derived to create the 2-DOF anti-swing controller. The anti-swing controller is added to the electro-hydraulic motion controller via feedforward. A dynamic simulation model of the crane is made, and the control system is evaluated in simulations with a path controller in actuator space. Simulation results show significant reduction in the load swing angle during motion. Experiments are carried out to verify the perf…
Simulated 3-axis versus 5-axis Processing Toolpaths for Single Point Incremental Forming
2019
Abstract Accuracy and productivity of the parts manufactured by single point incremental forming (SPIF) are influenced by the proper selection of toolpaths. CAM software packages are often used for generating the toolpaths for the process. Literature survey have revealed that contour curves and spatial spirals are the most used toolpaths for SPIF. These toolpaths are generated using 3-axis approaches, meaning that the tool axis is maintained parallel to the vertical axis. The 3-axis approach was justified using 3-axis CNC milling machines as the main technological equipment for SPIF. However, nowadays, the wide spreading of both 5-axis CNC milling machines and industrial robots, with far su…
Autonomous 3D geometry reconstruction through robot-manipulated optical sensors
2021
Abstract Many industrial sectors face increasing production demands and need to reduce costs, without compromising the quality. Whereas mass production relies on well-established protocols, small production facilities with small lot sizes struggle to update their highly changeable production at reasonable costs. The use of robotics and automation has grown significantly in recent years, but extremely versatile robotic manipulators are still not commonly used in small factories. Beside of the investments required to enable efficient and profitable use of robot technology, the efforts needed to program robots are only economically viable in case of large lot sizes. Generating robot programs f…