Search results for "paper industry"

Effect of micro-aeration and leachate replacement on COD solubilization and VFA production during mono-digestion of grass-silage in one-stage leach-b…

2010

The effect of micro-aeration and leachate replacement with fresh water on chemical oxygen demand (COD) solubilization and volatile fatty acid (VFA) production during the mono-digestion of grass-silage in one-stage leach-bed reactors (LBRs) was investigated in four LBRs, L0 (control), L1, L2 and L3 in batch mode at 35 + or - 1 degrees Celsius for 57 days. Results showed that leachate replacement without pH adjustment (L3) resulted in 2.7 and 1.3 times more SCOD in the leachate compared to control (L0) or leachate replacement with initial pH adjustment (L1), respectively. Micro-aeration at flow rate of 1 L min(-1) (2.5 L of air) in L2 resulted in 4-fold increase in VFA production (from 2.2 to…

Biological Nutrient Removal Model No. 2 (BNRM2): a general model for wastewater treatment plants

2013

This paper presents the plant-wide model Biological Nutrient Removal Model No. 2 (BNRM2). Since nitrite was not considered in the BNRM1, and this previous model also failed to accurately simulate the anaerobic digestion because precipitation processes were not considered, an extension of BNRM1 has been developed. This extension comprises all the components and processes required to simulate nitrogen removal via nitrite and the formation of the solids most likely to precipitate in anaerobic digesters. The solids considered in BNRM2 are: struvite, amorphous calcium phosphate, hidroxyapatite, newberite, vivianite, strengite, variscite, and calcium carbonate. With regard to nitrogen removal via…

A spectroscopic method for determining lignin content of softwood and hardwood kraft pulps

1998

Abstract A rapid method for determining the kappa number of unbleached and oxygen-delignified kraft pulps in the range 3–35 is presented. This novel method was based on the multivariate analysis of VIS spectral data on pulp samples. The calculated models and the test results indicated that partial least squares (PLS) and principal component regression (PCR) models yielded similar results, PLS being slightly more accurate. It was also found that for practical purposes a separate model for each wood feedstock and delignification process is needed.

Estimation of pulp yield in industrial oxygen-alkali delignification of softwood kraft pulp

2002

Fate of Oxygen in Industrial Oxygen-Alkali Delignification of Softwood Kraft Pulp

2004

Molecular Mass Distribution of Lignin from the Alkaline Pulping of Hardwood, Softwood, and Wheat Straw

2012

Abstract The behavior of lignin during kraft (hardwood, softwood, and wheat straw) and soda-AQ (wheat straw) pulping was studied, mainly in terms of delignification degree and molecular mass distribution (MMD). In the initial delignification phase (at 140°C for 15–60 min), a prominent part of the dissolved softwood kraft lignin (18–25 g/L, MM mostly > 3,000 Da) was found in the liquid phase of chip cavities, rather than in the external bulk black liquor (5–7 g/L, MM mostly < 3,000 Da). The maximum weight average MM values ( w) of the soluble lignin under conventional cooking conditions were detected for the kraft softwood (4,100 Da), and kraft birch (3,400 Da) when the degree of delignifica…

CHEMICAL PULPING. Oxidative degradation of AOX in softwood-based kraft mill effluents from E C F bleachin g

2012

Abstract Softwood-based kraft mill bleaching effluents from the initial bleaching stages D0 and E1 (the bleaching sequence being D0E 1D 1 E2D2) were treated by the oxidative Fenton method (H20rFeS04) to decompose organic pollutants contammg adsorbable organic halogens (AOX). Experiments designed using the Taguchi method were applied to predict the process conditions that would result in a cost-effective and adequate removal of AOX. In addition to the composition and concentration of the reagents (H202 and Fe2+), the main process parameters selected were temperature and reaction time, while pH was adj usted to an approximate value of 4 (the volumetric ratio of the mixed effluents D0:E 1 was …

A LASER-INDUCED FLUORESCENCE (LIF) METHOD FOR MONITORING OXYGEN–ALKALI DELIGNIFICATION OF SOFTWOOD KRAFT PULP

2002

ABSTRACT A laser-induced fluorescence (LIF) method for monitoring the oxygen–alkali delignification of pine (Pinus sylvestris) kraft pulp was tested. The fluorescence intensity of the effluent was found to increase systematically during treatment as the lignin content of the pulp decreased. This emission method, compared, for example, to a UV/Vis absorption method, seems to have potential for large-scale applications. Owing both to the complex chemical nature of the effluent from oxygen–alkali delignification and to the complex nature of the fluorescence method, further work on this method is needed before it can be used for industrial purposes.

Combustion behavior of kraft black liquor droplets from hot water pretreated hardwood and softwood chips

2016

This paper describes the combustion behavior of birch and spruce kraft black liquors obtained from an integrated forest biorefinery concept in which a hot water extraction of chips was performed before pulping. This pretreatment, aiming mainly at the recovery of various hemicellulose-derived materials, increased the concentrations of lignin and hydroxy acids in black liquors, compared with those in the reference black liquors without any process modification. On the other hand, the pretreatment decreased the concentrations of volatile acids and other organics (extractives and hemicellulose residues). Because of these characteristic changes, the total burning times (pyrolysis time plus char …

Novel biomass fly ash-based geopolymeric mortars using lime slaker grits as aggregate for applications in construction: Influence of granulometry and…

2019

Abstract This work discusses the influence of the aggregate granulometry and the binder/aggregate ratio on the engineering properties of novel green geopolymeric mortars. Two wastes generated by a Portuguese Kraft pulp industry are employed to manufacture the material: lime slaker grits (used as aggregate) and biomass fly ash (to partially replace the metakaolin − 70 wt% substitution). The novel geopolymeric mortars could find innovative applications as sustainable construction materials. The studied mix design foresees the use of several grits granulometric ranges and ratios binder/aggregate to discuss workability, water sorptivity, and mechanical performance of the novel mortars. To date,…