Search results for "penetration depth"
showing 10 items of 34 documents
Optical determination of the oxygen content of YBa2Cu3O6+x thin films by IR reflectance and transmittance measurements
2001
Abstract Recent studies of the optical properties of YBa2Cu3O6+x (YBCO) single crystals by several authors have shown that the optical conductivity in the infrared spectral region is a sensitive function of the oxygen content of the samples. Infrared spectroscopy thus offers a possibility for oxygen concentration analysis and is an alternative to other methods such as (i) the X-ray determination of the length of the c-axis and (ii) spectroscopic ellipsometry at an electronic transition band centered around 4.1 eV whose strength decreases with increasing oxygen content. We explore the applicability of the IR optical method for the case of YBCO thin films of about 300 nm thickness which are e…
Disorder-induced Raman scattering in rhenium trioxide (ReO3)
2007
Raman scattering in cubic metallic perovskite (ReO3) was studied at room temperature for well-crystallized monolith, polycrystalline powder and thin film samples. Defect-induced first-order Raman scattering was detected from the sub-surface region, given by the penetration depth of a 633 nm laser, and its origin was explained on the basis of a rigid-ion vibrational model for bulk ReO3. A quenching of the Raman intensity was observed in crystalline monolithic ReO3 upon increasing the temperature up to 250 °C and was related to crystal surface reconstruction/annealing.
Bond strength of a new Kevlar fiber-reinforced composite post with semi-interpenetrating polymer network (IPN) matrix
2019
Background This study aimed to evaluate the bond strength and the penetration depth of two adhesive systems to a new experimental semi-IPN fiber post versus a commercial post. Material and Methods Experimental Kevlar fiber (KF) and control everStick®POST (ES) posts (n=20/ group) with a diameter of 1.5 mm were used, 10 posts coated with StickResin (SR) and the other 10 posts coated with Scotch bond multipurpose (SBMP) adhesives. Composite resin buildup was performed over each post, using a cylindrical plastic mold (10 mm × 6 mm). Four discs of 2 mm thickness were prepared from each post/composite buildup and underwent pushout bond strength test at a crosshead speed of 0.5 mm/min accompanied …
Simulation of liquid penetration in paper
2006
Capillary penetration of a wetting liquid in a microtomographic image of paper board, whose linear dimension was close to the average length of wood fibers, was simulated by the lattice-Boltzmann method. In spite of the size of the system not being large with respect to the size of structural inhomogeneities in the sample, for unidirectional penetration the simulated behavior was described well by that of the Lucas-Washburn equation, while for radial penetration a radial capillary equation described the behavior. In both cases the average penetration depth of the liquid front as a function of time followed a power law over many orders of magnitude. Capillary penetration of small droplets of…
Generation and excitation of point defects in silica by synchrotron radiation above the absorption edge
2010
We report photoluminescence measurements carried out on amorphous SiO{sub 2} upon excitation by synchrotron light. Exposure of the as-grown material to above-edge light at low temperature induces the formation of nonbridging oxygen hole centers (NBOHC), localized in a thin layer below the surface limited by the penetration depth (tens of nm) of impinging light. After concluding the exposure to 11 eV light, stable defects are revealed by observing their characteristic 1.9 eV photoemission band excited at 4. 8eV. The local concentration of induced defects, supposedly formed by nonradiative decay of excitons, is very high (close to approx10{sup 21} cm{sup -3}) and independent of the previous h…
Linking structure and nanomechanical properties via instrumented nanoindentations on well-defined and fine-tuned morphology poly(ethylene)
2009
Several poly(ethylene) samples with a broad range of morphologies were studied in this work using nanoindentations. The samples had degrees of crystallinity ranging from 30 to 100% while their Young's modulus ranged from few tens of MPa up to several GPa. Experimental conditions for the correct evaluation of Young's modulus were at first identified, choosing a suitable loading rate in order to minimize viscoelastic effects on the unloading. The force curves, i.e., plots of applied load vs. penetration depth, were then analyzed following two common procedures available in the literature. None of these procedures leads to satisfying results when compared to other experimental techniques. Howe…
Influence of a Crosslinker Containing an Azo Group on the Actuation Properties of a Photoactuating LCE System
2016
Photoactuating liquid crystalline elastomers (LCE) are promising candidates for an application as artificial muscles in microdevices. In this work, we demonstrate that by optimizing (1) the illumination conditions and (2) the mixture of azo monomer and azo crosslinker, thick films of an all-azo LCE can be prepared, which show a strong length change without bending during photoactuation. This becomes possible by working with white light (about 440 nm), whose absorption is low, leading to a large penetration depth. By adding an azo crosslinker to a previously prepared system, several improvements of the actuation properties—like a stronger photoactuation at lower operational temperatures—coul…
Statistical prediction of corrosion front penetration
1997
A statistical method to predict the stochastic evolution of corrosion fronts has been developed. The method is based on recording material loss and maximum front depth. In this paper we introduce the method and test its applicability. In the absence of experimental data we use simulation data from a three-dimensional corrosion model for this test. The corrosion model simulates localized breakdown of a protective oxide layer, hydrolysis of corrosion product and repassivation of the exposed surface. In the long time limit of the model, pits tend to coalesce. For different model parameters the model reproduces corrosion patterns observed in experiment. The statistical prediction method is base…
Dependence of the Optical Constant Parameters of p-Toluene Sulfonic Acid-Doped Polyaniline and Its Composites on Dispersion Solvents
2020
The optical constants of Para-Toluene sulfonic acid-doped polyaniline (PANI), PANIchitosan composites, PANI-reduced graphene-oxide composites and a ternary composite comprising of PANI, chitosan and reduced graphene-oxide dispersed in diluted p-toluene sulfonic acid (PTSA) solution and N-Methyl-2-Pyrrolidone (NMP) solvent have been evaluated and compared. The optical constant values were extracted from the absorbance spectra of thin layers of the respective samples. The potential utilization of the materials as the active sensing materials of surface plasmon resonance biosensors has also been assessed in terms of the estimated value of the penetration depth through a dielectric medium. The …
Quantitative subsurface defect detection in composite materials using a non-contact ultrasonic system
2002
The results of an experimental study conducted to detect subsurface defects in a thick Gr/PPS composite test sample using a noncontact ultrasonic system are presented. Surface waves are generated by a pulsed laser and detected by an air-coupled capacitance transducer. By controlling the surface wave wavelength through a shadow mask, it is possible to control surface wave penetration depth in the sample. Surface wave peak-to-peak amplitude is related to the near-surface material condition. Results indicate that signal amplitude decreases as the width of the defect increases and an approximately linear relation can be deduced.