Search results for "phase noise"
showing 8 items of 28 documents
Noise Analysis and Comparison of Phase-and Frequency-Detecting Readout Systems: Application to SAW Delay Line Magnetic Field Sensor
2019
International audience; Transmission surface acoustic wave (SAW) sensors are widely used in various fields of application. In order to improve the limit of detection (LOD) of such sensor systems, it is essential to understand and quantify the relevant noise sources. Only then, strategies for noise reduction can be developed. In this paper, low noise readout systems for the application with SAW sensors in an open-loop and a closed-loop configuration are presented and experimentally investigated with regard to their phase noise on the example of a SAW delay line magnetic field sensor. Besides a comprehensive analysis of the phaseand frequency modulated signals, respectively, previously derive…
Noise characterization of analog to digital converters for amplitude and phase noise measurements
2017
International audience; Improvements on electronic technology in recent years have allowed the application of digital techniques in phase noise metrology where low noise and high accuracy are required, yielding flexibility in systems implementation and setup. This results in measurement systems with extended capabilities, additional functionalities and ease of use. In most digital schemes the Analog to Digital Converters (ADCs) set the ultimate performance of the system, therefore the proper selection of this component is a critical issue. Currently, the information available in literature describes in depth the ADC features only at frequency offsets far from the carrier. However, the perfo…
Equivalence of Open-Loop and Closed-Loop Operation of SAW Resonators and Delay Lines
2019
International audience; Surface acoustic wave (SAW) sensors in the form of two-port resonators or delay lines are widely used in various fields of application. The readout of such sensors is achieved by electronic systems operating either in an open-loop or in a closed-loop configuration. The mode of operation of the sensor system is usually chosen based on requirements like, e.g., bandwidth, dynamic range, linearity, costs, and immunity against environmental influences. Because the limit of detection (LOD) at the output of a sensor system is often one of the most important figures of merit, both readout structures, i.e., open-loop and closed-loop systems, are analyzed in terms of the minim…
Residual Phase Noise Measurement of Optical Second Harmonic Generation in PPLN Waveguides
2017
We report on the characterization, including residual phase noise and fractional frequency instability, of fiber-coupled PPLN non-linear crystals. These components are devoted to frequency doubling 871 nm light from an extended-cavity diode laser to produce a 435.5 nm beam, corresponding to the ytterbium ion electric quadrupole clock transition. We measure doubling efficiencies of up to 117.5 %/W. Using a Mach-Zehnder interferometer and an original noise rejection technique, the residual phase noise of the doublers is estimated to be lower than ${\rm -35\, dBrad^2/Hz}$ at 1 Hz, making these modules compatible with up-to-date optical clocks and ultra-stable cavities. The influence of externa…
Phase-Noise and Amplitude-Noise Measurement of DACs and DDSs
2019
This article proposes a method for the measurement of Phase Noise (PN, or PM noise) and Amplitude Noise (AN, or AM noise) of Digital-to-Analog Converters (DAC) and Direct Digital Synthesizers (DDS) based on modulation-index amplification. The carrier is first reduced by a controlled amount (30-40 dB) by adding a reference signal of nearly equal amplitude and opposite in phase. Then, residual carrier and noise sidebands are amplified and sent to a conventional PN analyzer. The main virtues of our method are: (i) the noise specs of the PN analyzer are relaxed by a factor equal to the carrier suppression ratio; and, (ii) the capability to measure the AN using a PN analyzer, with no need for th…
Noise effect in a FitzHugh-Nagumo circuit driven by a bichromatic signal
2013
We analyze the response of a nonlinear circuit exactly ruled by the FitzHugh-Nagumo equations. This circuit is submitted to a bichromatic signal including a high frequency and a low frequency. In absence of noise, we show that for an appropriate amplitude of the high frequency driving, the response of the circuit estimated at the low frequency can be optimized via the phenomenon of vibrational resonance. Next, we show that under certain conditions, noise can contribute to the effect of vibrational resonance. Colored noise is also considered. Our experimental results are confirmed by a numerical analysis.
Noise effect in a sine-Gordon Lattice
2013
International audience; This paper is devoted to the influence of internal noise in a sine-Gordon chain exhibiting the well known nonlinear supratransmission phenomenon. It is shown that spatiotemporal noise can trigger breather modes with a given probability in a range of parameters where they do not occur without noise. A frequency analysis is carried out to quantify the degree of coherence of the emitted breather. It is shown that there exists an appropriate amount of noise which ensures the existence of breather modes with the best coherence.
Thermal noise limit for ultra-high vacuum noncontact atomic force microscopy
2013
The noise of the frequency-shift signal Δf in noncontact atomic force microscopy (NC-AFM) consists of cantilever thermal noise, tip–surface-interaction noise and instrumental noise from the detection and signal processing systems. We investigate how the displacement-noise spectral density dz at the input of the frequency demodulator propagates to the frequency-shift-noise spectral density dΔf at the demodulator output in dependence of cantilever properties and settings of the signal processing electronics in the limit of a negligible tip–surface interaction and a measurement under ultrahigh-vacuum conditions. For a quantification of the noise figures, we calibrate the cantilever displacemen…