Search results for "phosphoric acid"

Bulk filling of Class II cavities with a dual-cure composite: Effect of curing mode and enamel etching on marginal adaptation.

2014

Objectives: This study attempted to find a simple adhesive restorative technique for class I and II cavities on posterior teeth. Study Design: The tested materials were a self-etching adhesive (Parabond, Coltene/Whaledent) and a dual-cure composite (Paracore, Coltene/Whaledent) used in bulk to restore the cavities. Class II MO cavities were performed and assigned to 4 groups depending on the orthophosphoric acid (H3PO4) conditioning of enamel and polymerization method used (chemical or dual). Specimens were subjected to quantitative marginal analysis before and after thermo-mechanical loading. Results: Higher percentages of marginal adaptation at the total margin length, both before and aft…

POSITIONING SELF-ETCHING ADHESIVES: VERSUS OR IN ADDITION TO PHOSPHORIC ACID ETCHING?

2004

Effect of metallacarborane salt H[COSANE] doping on the performance properties of polybenzimidazole membranes for high temperature PEMFCs

2020

[EN] In this paper, a series of composite proton exchange membranes comprising a cobaltacarborane protonated H[Co(C2B9H11)(2)] named (H[COSANE]) and polybenzimidazole (PBI) for a high temperature proton exchange membrane fuel cell (PEMFC) is reported, with the aim of enhancing the proton conductivity of PBI membranes doped with phosphoric acid. The effects of the anion [Co(C2B9H11)(2)] concentration in three different polymeric matrices based on the PBI structure, poly(2,2 '-(m-phenylene)-5,5 '-bibenzimidazole) (PBI-1), poly[2,2 '-(p-oxydiphenylene)-5,5 '-bibenzimidazole] (PBI-2) and poly(2,2 '-(p-hexafluoroisopropylidene)-5,5 '-bibenzimidazole) (PBI-3), have been investigated. The conducti…

Resistance of bonded premolars to four artificial ageing models post enamel conditioning with a novel calcium-phosphate paste

2020

Background This in vitro study compares a novel calcium-phosphate etchant paste to conventional 37% phosphoric acid gel for bonding metal and ceramic brackets by evaluating the shear bond strength, remnant adhesive and enamel damage following water storage, acid challenge and fatigue loading. Material and Methods Metal and ceramic brackets were bonded to 240 extracted human premolars using two enamel conditioning protocols: conventional 37% phosphoric acid (PA) gel (control), and an acidic calcium-phosphate (CaP) paste. The CaP paste was prepared from β-tricalcium phosphate and monocalcium phosphate monohydrate powders mixed with 37% phosphoric acid solution, and the resulting phase was con…

Strukturelle Veränderungen in säuregeätztem Schmelz im konfokalen Laser-Scanning-Mikroskop

1996

The aim of the present investigation was to elucidate structural alternations in enamel subjected to acid etch technique and treatment under remineralizing conditions by means of a new microscopy technique known as confocal laser scanning microscopy (CLSM). Blocks of enamel were treated with 37% phosphoric acid and exposed for 3 weeks to an oral environment. Tomographic CLSM images were subsequently obtained and compared with controls. CLSM proved to be a reliable, highly reproducible and simple method of qualitative assessment of structural changes occurring on the surface of enamel and in areas below the surface as deep as 100 microns or more. Structural alterations associated with acid a…

Determining efficacy of monitoring devices on ceramic bond to resin composite

2012

Objectives: This paper aims to assess the effectiveness of 3D nanoroughness and 2D microroughness evaluations, by their correlation with contact angle measurements and shear bond strength test, in order to evaluate the effect of two different acids conditioning on the bonding efficacy of a leucite-based glass-ceramic to a composite resin. Study Design: Ceramic (IPS Empress) blocks were treated as follows: 1) no treatment, 2) 37% phosphoric acid (H3PO4), 15 s, 3) 9% hydrofluoric acid (HF), 5 min. Micro- and nano-roughness were assessed with a profilometer and by means of an atomic force microscopy (AFM). Water contact angle (CA) measurements were determined to assess wettability of the ceram…

Studies of the Phosphatization of Steel and its Corrosion Products

1986

The reaction of phosphoric acid with steel is a basic process in many technological procedures. A typical example is the pretreatment of steel surfaces for the application of coatings. The aim of the treatment is to clean the surface, to produce a homogeneousr tight, and smooth cover and to provide a reliable adhesion between the steel substrate and the coating. This example points out that the phase composition of the layer formed is of great interest, and that reactions with residues on the surface, such as oxides and corrosion products, have to be considered, too. The same holds for phosphate layers formed in order to modify the mechanical or corrosion behavior of steel surfaces. Because…

A zinc-doped endodontic cement facilitates functional mineralization and stress dissipation at the dentin surface

2018

Objective: The purpose of this study was to evaluate nanohardness and viscoelastic behavior of dentin surfaces treated with two canal sealer cements for dentin remineralization. Material and Methods: Dentin surfaces were subjected to: i) 37% phosphoric acid (PA) or ii) 0.5 M ethylenediaminetetraacetic acid (EDTA) conditioning prior to the application of two experimental hydroxyapatite-based cements, containing sodium hydroxide (calcypatite) or zinc oxide (oxipatite), respectively. Samples were stored in simulated body fluid during 24 h or 21 d. The intertubular and peritubular dentin were evaluated using a nanoindenter to assess nanohardness (Hi). The load/displacement responses were used f…

Ionic Liquid Composite Polybenzimidazol Membranes for High Temperature PEMFC Applications

2019

A series of proton exchange membranes based on polybenzimidazole (PBI) were prepared using the low cost ionic liquids (ILs) derived from 1-butyl-3-methylimidazolium (BMIM) bearing different anions as conductive fillers in the polymeric matrix with the aim of enhancing the proton conductivity of PBI membranes. The composite membranes prepared by casting method (containing 5 wt. % of IL) exhibited good thermal, dimensional, mechanical, and oxidative stability for fuel cell applications. The effects of anion, temperature on the proton conductivity of phosphoric acid-doped membranes were systematically investigated by electrochemical impedance spectroscopy. The PBI composite membranes containin…

Electropolishing of CuZn brasses and 316L stainless steels: Influence of alloy composition or preparation process (ALM vs. standard method)

2016

International audience; In the present paper, electropolishing behavior of different brass alloys (CuZn39Pb2, CuZn42) in phosphoric acid is studied to observe the impact of alloying elements on polishing quality. In the same way, the influence of the manufacturing process is also evaluated through the comparison of a “standard” stainless steel and a stainless steel prepared by Additive Laser Manufacturing (ALM). An electrochemical study was first performed to determine the best treatment conditions for each material/electrolyte pair and to study the electropolishing mechanism and its kinetic dependence on diffusion. Metallic samples are fully characterized before and after electropolishing …