Search results for "polymers"
showing 10 items of 3567 documents
On the formation of lamellae during annealing of extended chain crystals of radiation-polymerized trioxane
1969
Abstract The structure changes of radiation-polymerized trioxane taking place during annealing have been studied by means of electron microscopy, X-ray small- and wide-angle scattering, and differential thermal analysis. The original fibrillar crystals, supposedly consisting of extended chains, change into lamellar crystals due to annealing at temperatures between 150° and 190°C. Lamella formation can be connected with the appearance of a long period of about 200A which is not observed in the unannealed sample. During annealing within the same temperature range the X-ray reflections due to the twin structure of the original polytrioxane disappear, whereas the orientation of the fraction wit…
Processing and mechanical properties of recycled PVC and of homopolymer blends with virgin PVC
1996
Mechanical and processing properties of recycled polyvinylchloride (PVC, from bottles and pipes) were compared with those of virgin pipe grade PVC. Blends of recycled and pipe grade PVC were also prepared and characterized. It was found that the particle size and the restabilization of the recycled PVC are the two main points to be considered for obtaining virgin/recycled PVC blends with uniform and good mechanical properties. In general, recycled PVC not only does not significantly reduce the modulus and tensile strength, but also improves the impact strength and processing behavior of pipe grade virgin PVC. Only the thermomechanical resistance is slightly lowered. The latter points hold, …
Effect of the processing techniques on the properties of ecocomposites based on vegetable oil-derived Mater-Bi® and wood flour
2009
Polymer composites based on biodegradable polymers and natural-organic fillers are becoming more and more important because of their interesting properties in terms of environmental impact, manufacturing cost, and esthetic features. In particular, the use of biodegradable polymer matrices allows obtaining a full biodegradability. One of the most interesting biodegradable polymer families is the Mater-Bi® one. In this work, we investigated the processability, the influence of different processing techniques, and the influence of the filler particle size on the properties of Mater-Bi/wood flour composites. Injection molding caused a partial degradation of the macromolecular chains, whereas si…
Effect of Polarity of Solvent on Silanization of Halloysite Nanoclay Using (3-Glycidyloxy propyl) Trimethoxy Silane
2021
Abstract: The grafting of silane groups on clay surfaces has been recently investigated in order to fabricate versatile compounds with new potential applications in materials science and ecological engineering. This work explored the influence of variety of solvents with variable polarity on the silanization of halloysite nanoclay (HNT) surface by (3-Glycidyloxy propyl) trimethoxy silane. To this purpose, the functionalization of HNT by 3-Glycidyloxypropyltrimethoxysilane (GOPTMS) has been conducted in Ethanol (polar protic solvent), Tetrahydrofuran (THF) and Acetonitrile (polar aprotic solvents), and Hexane, 1,4-Dioxane and Toluene (non polar solvents). The silane grafted materials were ch…
Morphology and properties of blends of polyethylene with a semiflexible liquid crystalline polymer
1995
Blends of three polyethylene (PE) samples (two HDPE grades and LLDPE) with an experimental sample of a semiflexible liquid crystalline polymer (SBH 1 :1 :2 by Eniricerche) have been prepared in a Brabender compounder. The processing-aid effect of the LCP has been demonstrated by the decreased energy required for extruding the blends, as compared to that needed for neat PE. The thermal properties, as studied by differential scanning calorimetry (DSC), have shown that the two components of the blends are immiscible. However, the dispersed SBH phase has been found to act as a nucleating agent for the crystallization of LLDPE, whereas no such effect was observed for HDPE. This has been taken as…
Dislocation interaction with C in α-Fe: a comparison between atomic simulations and elasticity theory
2008
International audience; The interaction of C atoms with a screw and an edge dislocation is modelled at an atomic scale using an empirical Fe-C interatomic potential based on the Embedded Atom Method (EAM) and molecular statics simulations. Results of atomic simulations are compared with predictions of elasticity theory. It is shown that a quantitative agreement can be obtained between both modelling techniques as long as anisotropic elastic calculations are performed and both the dilatation and the tetragonal distortion induced by the C interstitial are considered. Using isotropic elasticity allows to predict the main trends of the interaction and considering only the interstitial dilatatio…
Structure and thermal properties of a chitosan coated polyethylene bilayer film
2012
The thermal and the structural properties of chitosan coated polyethylene (PE) films were studied. The coating process did not significantly influence the thermal stability and the PE surface structure and/or composition of the polyolefin. Dehydration temperature of chitosan films reflected the strength of water/acetic acid/chitosan chains interactions. Glycerol, used as a plasticizer, formed new hydrophilic centres in the film matrix. Moreover it was better integrated in the CSEGLY than in CSAGLY network. Besides, the addition of a plasticizer in the chitosan films decreased the film degradation temperature. There were two main steps for the PE chitosan coated films degradation. The first …
Biodegradation paths of Mater-Bi®/kenaf biodegradable composites
2013
Composites obtained from biodegradable polymers and natural–organic fillers are attracting increasing interest, thanks to the environmental advantages they promise. On the other hand, the real biodegradation performance of a biodegradable polymer/natural organic filler composite should be assessed by performing specific biodegradation tests. These are often carried out under laboratory conditions, but more realistic conditions should be taken into account. In this work, a systematic study on the biodegradation of kenaf fiber-filled Mater-Bi® composites in different environments is presented, and some interesting parameters for the understanding of the optimum way to obtain a fast degradatio…
Matrix and Filler Recycling of Carbon and Glass Fiber-Reinforced Polymer Composites: A Review
2021
Fiber-reinforced polymers (FRPs) are low-density, high-performance composite materials, which find important applications in the automotive, aerospace, and energy industry, to only cite a few. With the increasing concerns about sustainability and environment risks, the problem of the recycling of such complex composite systems has been emerging in politics, industry, and academia. The issue is exacerbated by the increased use of FRPs in the automotive industry and by the expected decommissioning of airplanes and wind turbines amounting to thousands of metric tons of composite materials. Currently, the recycling of FRPs downcycles the entire composite to some form of reinforcement material (…
Modeling the influence of mineral content and porosity on ultrasound parameters in bone by using synthetic phantoms
1999
Model composite media − 10×15×80 mm3 bone tissue phantoms based on an epoxy resin with fillers—were made to study the influence of porosity and mineral content on ultrasound velocity and attenuation. The pores were simulated by ∼ 1 mm3 particles of a soft rubber, while the mineral content was imitated by a mineral residue of natural bone obtained by burning and grinding. The porosity and mineral content were varied in the range of 0–70% by volume with a step of 10%. The velocity, attenuation, and prevalent frequency of ultrasound were measured by the pulse transition method, using transducers with nominal frequencies 0.1, 0.2, 0.5, and 1.0 MHz. It was experimentally found that the ultrasoun…