Search results for "polymers"

Molecular surfaces: An advantageous starting point for the description of composition-dependent viscosities applied to polymer solutions

1999

The viscosity of polymer/solvent systems is modeled as a function of composition under the premises that the dissipation of energy is taking place at the molecular interfaces and that the friction between solvent and solute varies with composition due to a change in the flow mechanism (drainage of coils). The simple expression obtained in this manner contains three system-specific parameters: a geometric factor γ, which accounts for the differences of the surface to volume ratios of the components; a hydrodynamic parameter α, which measures the friction between solute and solvent in the case of fully draining polymer coils; and β, which corrects for changes in the friction between unlike mo…

Mechanical properties of injection-molded binary blends of polyethylene with small additions of a liquid-crystalline polymer

2011

The results of the investigation of the mechanical properties of polyethylene (PE) blends with small (<3 wt %) additions of thermotropic liquid-crystalline polymers (LCPs) are reported. PE/LCP compositions with various LCP weight contents were obtained by thermoplastic mixing in a two-stage process. Short-term and long-term mechanical behavior of various PE/LCP compositions were analyzed. Data on the influence of LCP addition on the tensile elastic modulus [or Young's modulus (E)], stress at yield (σY), stress at break (σB), strain at yield, strain at break, and deformation at long-term (1000-h) tensile creep were obtained. The experimental results of the investigation show that even small …

Synthesis and activity of zirconocene catalysts supported on silica-type sol-gel carrier for ethylene polymerization

2001

Synthesis and activity of bis(cyclopentadienyl)zirconium dichloride catalyst supported on unconventional silica-type material obtained in sol-gel process and activated by organoaluminium co-catalyst were studied. The effect of support modification conditions (thermal dehydration and/or modification by organoaluminium compound) and a type of co-catalyst on an activity of the catalytic system in ethylene polymerization and properties of resulting polymers were investigated and compared with results obtained earlier for vanadium catalysts supported on mentioned sol-gel carrier. The most appropriate method of the sol-gel silica-type support preparation is thermal pre-treating (200°C) followed b…

Surface and bulk ordering in thin films of a symmetrical diblock copolymer

2013

Amphiphilic diblock copolymers have the ability to adapt their surface's molecular composition to the hydrophilicity of their environment. In the case of about equal volume fractions of the two polymer blocks, the bulk of these polymers is known to develop a laminar ordering. We report here our investigation of the relationship between bulk ordering and surface morphology/chemical composition in thin films of such an amphiphilic diblock copolymer. Upon annealing in vacuum, the expected lamella ordering in the bulk of the film is observed and we find the morphology of the film surface to be defined by the thickness of the as-deposited film: If the as-deposited thickness matches the height of…

Thermo- and photo-oxidative stability and improved processability of polyamide stabilized with a new functional additive

2005

During processing polyamides can undergo thermo-mechanical degradation due to the mechanical stress and to the high temperature applied to the melt. Degradation can occur also during the polyamides lifetime due to many driving forces, like temperature, ultraviolet radiations, etc. The mechanisms of degradation are not well understood and the stabilization with usual stabilizers, like phenol antioxidants, is not so efficient as for other classes of polymers. The aim of this work is the study of the effects of the addition of a new multifunctional additive on the processing and on the thermo- and photo-stabilization of polyamide-6. This additive is able to prevent the thermo-mechanical degrad…

New amphiphilic conjugates of mono- and bis(carboxy)-PEG(2,000) polymers with lipoamino acids as surface modifiers of colloidal drug carriers

2010

Hydrogen peroxide sensing with horseradish peroxidase-modified polymer single conical nanochannels.

2011

Inspired from the funtioning and responsiveness of biological ion channels, researchers attempt to develop biosensing systems based on polymer and solid-state nanochannels. The applicability of these nanochannels for detection/sensing of any foreign analyte in the surrounding environment depends critically on the surface characteristics of the inner walls. Attaching recognition sites to the channel walls leads to the preparation of sensors targeted at a specific molecule. There are many nanochannel platforms for the detection of DNA and proteins, but only a few are capable of detecting small molecules. Here, we describe a nanochannel platform for the detection of hydrogen peroxide, H(2)O(2)…

Target Analogue Imprinted Polymers with Affinity for Folic Acid and Related Compounds

2001

Two approaches to synthesize molecularly imprinted polymers with affinity for folic acid and other substituted pteridines have been compared. In the first approach, the folic acid analogue methotrexate was used as template and functional monomers capable of generating selective binding sites were searched in a miniaturized screening system based on binding assessment in the batch mode. Highest selectivity was seen using 2-vinylpyridine as functional monomer, which was confirmed in the chromatographic mode for a batch synthesized on a gram scale. However, the retentivity and selectivity of this phase were insufficient for anticipated applications. In a second approach, using methacrylic acid…

Interplay between Chain Collapse and Microphase Separation in Bottle-Brush Polymers with Two Types of Side Chains

2010

Conformations of a bottle-brush polymer with two types (A,B) of grafted side chains are studied by molecular dynamics simulations, using a coarse-grained bead−spring model with side chains of up to...

Water-Blown Polyisocyanurate Foams From Vegetable Oil Polyols

2008

Polyols with the hydroxyl value OHV from 290 to 318 mg KOH/g are synthesized from rapeseed, sunflower seed, flaxseed, or coconut oils by the way of their: (1) transesterification with triethanolamine or (2) amidization with diethanolamine. The influence of water as the blowing agent on the storage stability of the polyol premix system is assessed from values of the polyol premix system pH, acid value, and variations in such parameters as cream and gel time. Water-blown polyisocyanurate (PIR) foams (150 · II × 300; II—isocyanate index) characterized by good mechanical characteristics, dimensional stability at 70°C and at relative humidity RH = 95% as well as by a very low water absorbance, …