Search results for "r process"
showing 10 items of 665 documents
Biomechanical analysis of two types of osseointegrated transfemoral prosthesis
2020
In the last two decades, osseointegrated prostheses have been shown to be a good alternative for lower limb amputees experiencing complications in using a traditional socket-type prosthesis
Natural Convection Cooling of a Hot Vertical Wall Wet by a Falling Liquid Film
2008
Abstract The system studied is a plane channel in which one of the two vertical walls is kept at an arbitrary temperature profile and may be partially or completely wet by a falling liquid film, while the opposite wall is adiabatic. Air from the environment flows along the channel with a mass flow rate which depends on the balance between hydraulic resistances and buoyancy forces. These latter, in their turn, depend on the distribution of temperature and humidity (hence, density) along the channel and eventually on the heat and mass transferred from wall and film to the humid air. A simplified computational model of the above system was developed and applied to the prediction of relevant qu…
Coupling between oxidation kinetics and anisothermal oil flow during deep-fat frying
2021
Deep-fat frying is a cooking technique that has been used continuously since prehistoric times. A domestic deep-fryer heated from the bottom develops significant convection inside the bath cavity. It is responsible for very high heat transfer coefficients and the exposure of the deep-frying oil to the atmospheric oxygen. The continuous conversion of gaseous dioxygen into unstable and reactive hydroperoxides and their subsequent advection throughout the bulk volume is at the origin of the main complaints made of frying which includes issues such as odors, fouling, and generation of several toxic compounds. This study analyzes the coupling between natural convection of triacylglycerols and th…
Generalization of a finite-difference numerical method for the steady-state and transient solutions of the nernst—planck flux equations
1985
Abstract A generalization of the numerical method of Brumleve and Buck for the solution of Nernst—Planck equations when convective flux and electric current are involved has been developed. The simulation procedure was applied to a specific case: transport of strong electrolytes in a wide-pore membrane with simultaneous diffusion, convection and electric current. Good agreement was found between experimental data and computed results.
Design and Experimental Test of a Thermomagnetic Motor
2012
Abstract This paper presents a Thermomagnetic Motor. The design of the motor is based on a thermal-magnetic coupled dynamic model, which is obtained by assuming the use of a ferromagnetic material working at temperatures near the curie point. The motor is modeled in terms of both its magnetic as well thermal properties (magnetic permeability and thermal conductivity) and the thermal processes are supposed to be influenced by the thermal conductivity, the convection and the advection. An analytical expression of the generated torque, which links this quantity to the magnetic, thermal and geometrical parameters of the generated torque is given. A design of a machine, based on this theory is p…
Onset of Convection in an Inclined Anisotropic Porous Layer with Internal Heat Generation
2019
The onset of convection in an inclined porous layer which is heated internally by a uniform distribution of heat sources is considered. We investigate the combined effects of inclination, anisotropy and internal heat generation on the linear instability of the basic parallel flow. When the Rayleigh number is sufficiently large, instability occurs and a convective motion is set up. It turns out that the preferred motion at convection onset depends quite strongly on the anisotropy ratio, &xi
Preparation and characterization of brass-based coatings
2018
Cold Spray (CS) has been widely investigated owing to its high deposition efficiency and retention of the properties of starting materials. Thus, this process has shown obvious advantages over the fabrication of different copper-based deposits and its alloys over other techniques, such as electroplating, Laser Cladding or thermal spraying. As one of the main copper alloys, brass is implanted in the fields of architecture or industry. Nevertheless, nowadays it is clear that there is very little work on brass coatings, and they were mainly made by electroplating and any other deposition methods, which has severely limits their uses in many applications.This study was applied to develop the br…
Volumetric changes in alveolar ridge preservation with a compromised buccal wall: a systematic review and meta-analysis.
2020
Background Many studies have addressed socket preservation, though fewer publications considering buccal wall loss can be found, since the literature typically considers sockets with four walls. A systematic review was made on the influence of type II buccal bone defects, according to Elian’s Classification, in socket grafting materials upon volumetric changes in width and height. Material and Methods An electronic and manual literature search was conducted in accordance to PRISMA statement. The search strategy was restricted to randomized controlled trials (RCTs) and controlled clinical trials (CCTs) describing post-extraction sockets with loss of buccal wall in which alveolar ridge preser…
Interaction with OGG1 Is Required for Efficient Recruitment of XRCC1 to Base Excision Repair and Maintenance of Genetic Stability after Exposure to O…
2015
International audience; XRCC1 is an essential protein required for the maintenance of genomic stability through its implication in DNA repair. The main function of XRCC1 is associated with its role in the single-strand break (SSB) and base excision repair (BER) pathways that share several enzymatic steps. We show here that the polymorphic XRCC1 variant R194W presents a defect in its interaction with the DNA glycosylase OGG1 after oxidative stress. While proficient for single-strand break repair (SSBR), this variant does not colocalize with OGG1, reflecting a defect in its involvement in BER. Consistent with a role of XRCC1 in the coordination of the BER pathway, induction of oxidative base …
Interaction between turbulent structures and particles in roughened channel
2016
Abstract The distribution of inertial particles in turbulent flows is highly non-uniform and is driven by the local dynamics of the turbulent structures of the underlying carrier flow field. In the specific context of dilute particle-laden wall-bounded flows, deposition and resuspension mechanisms are dominated by the interaction between inertial particles and coherent turbulent structures characteristic of the wall region. The macroscopic behavior of these two-phase systems is influenced by particle inertia, which plays a role at the microscale of a single dispersed element. These turbulent structures, which control the turbulent regeneration cycles, are strongly affected by the wall rough…