Search results for "scanning"
showing 10 items of 1808 documents
Modeling the interactions between light and crystallizing polymer during fast cooling
2004
In this work, an experimental set-up able to quench thin polymer films whilst recording the sample thermal history as well as the overall and depolarized light intensities of a laser beam emerging from the sample is described. The interactions between the light beam and the crystallizing material have been modeled accounting for absorption and scattering phenomena. The proposed model was found to be able to reproduce the ex- perimentally observed behavior of light intensities and it was validated by comparison with conventional DSC analysis. On the basis of this model, a method to obtain crystallinity evo- lution is proposed and applied to some fast cooling runs. The method was applied to q…
Image enhancement in photoemission electron microscopy by means of imaging time-of-flight analysis
2004
Abstract Photoemission electron microscopy (PEEM) is widely used in combination with synchrotron sources as a powerful tool to observe chemical and magnetic properties of metal and semiconductor surfaces. Presently, the resolution limit of these instruments using soft-X-ray excitation is limited to about 50 nm, because of the chromatic aberation of the electron optics used. Various sophisticated approaches have thus been reported for enhancing the spatial resolution in photoemission electron microscopy. This work demonstrates the use of a simple imaging energy filter based on electron time-of-flight (ToF) selection. The spatial resolution could be improved dramatically, even though the inst…
Heat shrinkable behavior, physico-mechanical and structure properties of electron beam cross-linked blends of high-density polyethylene with acryloni…
2016
Abstract In this study, heat-shrinkable composites of electron beam irradiated high-density polyethylene (HDPE) composites with acrylonitrile-butadiene rubber (NBR) were investigated. HDPE/NBR blends at a ratio of components 100/0, 90/10, 80/20, 50/50 and 20/80 wt% were prepared using a two-roll mill. The compression molded films were irradiated high-energy (5 MeV) accelerated electrons up to irradiation absorbed doses of 100–300 kGy. The effect of electron beam induced cross-linking was evaluated by the changes of mechanical properties, gel content and by the differences of thermal properties, detected by differential scanning calorimetry. The thermo-shrinkage forces were determined as the…
Spectral Measurement of Photon Emission from Individual Gold Nanoparticles Using Scanning Tunneling Microscopy
2016
The light emission spectra of individual Au nanoparticles induced by a scanning tunneling microscope (STM) have been investigated. Two-dimensional ensembles of tunnel-coupled Au particles were prepared by thermal evaporation onto a native oxide silicon wafer in ultrahigh vacuum (10 – 9 mbar). Our STM measurements show a single peak at photon energy 1.6 eV in the tunneling mode and two peaks at 2.2 eV (connected with the Mie plasmon) and 1.45 eV (a new peak which was not discussed in literature before) in the field emission mode.
The luminescence of ZnO ceramics
2010
Abstract The luminescence properties of ZnO ceramics with grains 100–5000 nm sintered by different techniques from nanopowders were studied. The luminescence decay times were compared with that obtained for ZnO single crystal. The temperature dependence of non-exponential decay of defect luminescence (2.0–2.6 eV) was measured in wide time, intensity and temperature range. The luminescence decay kinetic at T ≤ 20 K shows the decay close to I(t) ∼ t−1 dependence. At temperature region 50–250 K the decay kinetics is more complicate since the TSL was observed in this temperature region. It is shown that the luminescence properties of NP and ceramics strongly depend on defect distribution on gra…
Poisoning histories in the Italian renaissance: The case of Pico Della Mirandola and Angelo Poliziano.
2018
Giovanni Pico della Mirandola and Angelo Poliziano were two of the most important humanists of the Italian Renaissance. They died suddenly in 1494 and their deaths have been for centuries a subject of debate. The exhumation of their remains offered the opportunity to study the cause of their death through a multidisciplinary research project. Anthropological analyses, together with documentary evidences, radiocarbon dating and ancient DNA analysis supported the identification of the remains attributed to Pico. Macroscopic examination did not reveal paleopathological lesions or signs related to syphilis. Heavy metals analysis, carried out on bones and mummified tissues, showed that in Pico's…
End-to-end tests using alanine dosimetry in scanned proton beams
2018
This paper describes end-to-end test procedures as the last fundamental step of medical commissioning before starting clinical operation of the MedAustron synchrotron-based pencil beam scanning (PBS) therapy facility with protons. One in-house homogeneous phantom and two anthropomorphic heterogeneous (head and pelvis) phantoms were used for end-to-end tests at MedAustron. The phantoms were equipped with alanine detectors, radiochromic films and ionization chambers. The correction for the 'quenching' effect of alanine pellets was implemented in the Monte Carlo platform of the evaluation version of RayStation TPS. During the end-to-end tests, the phantoms were transferred through the workflow…
Number, Mass and Volume Distributions of Mineral Aerosol and Soils of the Sahara
1983
Abstract A direct method will be described to determine the complete mineral size distribution in aerosol (xylene-insoluble component) and soils (water-insoluble component) covering a size range from 0.01 up to 100 μm and 1000 μm radius, respectively, by using a combination of a scanning electron microscope, optical microscope and sieving. Aerosol and soil samples from the Sahara have been investigated. All mineral aerosol size distributions indicate a maximum between 0.06 and 0.08 μm radius and mineral particles have been found in the Aitken size range down to 0.02 μm radius. The concentration decrease toward larger particles is not uniform and shows considerable variations below 0.5 μm an…
Real-time manipulation of ZnO nanowires on a flat surface employed for tribological measurements: Experimental methods and modeling
2012
Elastic and tribological properties of zinc oxide nanowires (NWs) on Si wafer and highly oriented pyrolytic graphite (HOPG) are experimentally investigated and theoretically interpreted. Measurements are performed inside a scanning electron microscope (SEM) using real-time manipulation technique that enables two possible ways of data registration: “external” force registration with quartz tuning fork (QTF) based sensor and “internal” force registration utilizing in situ observed elastic deformation of NWs. Young modulus is determined by loading half-suspended NW at its free end and then employed for the following tribological experiments. Maximal static friction force is estimated when NW i…
Identification of Precious Artefacts: The Sonic Imprint for Small Artefacts
2010
Identification of artworks is mainly based on a few characteristics which can be observed using non-invasive tools (sight, touch, simple instruments), the investigated properties being geometry, weight, colours, texture, etc. Nowadays, technology allows reproducing all these characteristics to such an extent that even expert conservators can be deceived: in particular at the present time even the geometry of an artwork can be easily reproduced with the help of laser scanner analysis and with a rapid prototyping machine or a computer numerical control (CNC) milling machine. We propose a new tool, the Sonic Imprint, producing a code capable of identifying a rigid artefact from its vibrational…