Search results for "shrinkage"
showing 10 items of 78 documents
Hygroexpansivity of anisotropic sheets
2015
Dimensional instability, more particularly its component hygroexpansivity, may cause problems in process or end-use situations in which paper or board is in contact with water or subject to changes in ambient relative humidity. Misregistration in printing, curl during copying and calender wrinkles are examples of such defects. In this paper, the in-plane hygroexpansivity of oriented laboratory sheets with different pulps and dried both freely and under restraint is studied. A linear relationship between the drying shrinkage and hygroexpansion coefficient of freely dried laboratory sheets having different fiber orientation anisotropies, was observed. Regardless of both the measurement direct…
Improvement in the performance of low temperature H2-O2 fuel cell with chitosanephosphotungstic acid composite membranes
2016
Abstract Free-standing chitosan/phosphotungstic acid polyelectrolyte membranes, prepared by ionotropic gelation on alumina porous supports, were employed as proton conductor in low temperature H 2 –O 2 fuel cell. A drying step on glass substrate was introduced in the fabrication procedure to reduce shrinkage and consequent corrugation. Membranes were tested with electrodes prepared according to different procedures and with two different Pt loadings, namely 0.5 and 1 mg cm −2 . Both the investigated kinds of electrodes allowed to get very promising power peaks of 550 mW cm −2 in spite of the different Pt content. The polarization curves and the electrochemical impedance spectra suggest that…
Thermal and dynamic mechanical properties of beeswax-halloysite nanocomposites for consolidating waterlogged archaeological woods
2015
Abstract Thermal and mechanical properties were determined for the halloysite nanotubes (HNT)/beeswax composites at various compositions. The beeswax degradation temperatures and time course, provided by thermogravimetry (TG), evidenced the improvement of the thermal properties operated by HNT. Differential scanning calorimetry (DSC) allowed us to determine the enthalpy of melting as well as the time course of the melting process for beeswax. A slight loss of beeswax crystallinity was observed upon HNT addition. The dynamical mechanical analysis (DMA) provided the loss and the storage modulus for the nanocomposites upon heating and it was shown that the nanoclays create an inorganic framewo…
Water retention behaviour of compacted and reconstituted scaly clays
2020
The paper presents the results of an experimental research devoted to investigate the response to suction variations of a scaly clay in compacted and reconstituted conditions. Different experimental techniques (axis translation, vapour equilibrium, dew point psychrometer suction measurements) were combined in order to explore the water retention properties in a wide suction range (0 ÷ 110 MPa). Experimental results allowed to define the water retention domains for a constant reference void ratio, highlighting the significant role of the microstructure on the response of the investigated clays. In particular, the collected results showed that in the low-medium suction range, the peculiar mic…
Moisture loss, gain and migration in foods
2011
Abstract: The loss, gain and transfer of moisture often affect food materials. Whether arising from interaction with the atmosphere or with another component of the food, such changes always cause deterioration of the overall quality of the food through softening, toughening, breakdown, swelling or shrinkage due to phase transitions or dissolution. In most cases, water migration leads to organoleptic or microbiological changes in the food. With a view to better understanding the physical deterioration of food and to providing a tool for better control of food quality (and therefore of longer shelf life), this chapter reviews the water relationships in foods with particular attention to, and…
On the hydro-mechanical behaviour of a lime-treated embankment during wetting and drying cycles
2018
Abstract The paper presents some experimental results obtained on samples extracted from a full-scale embankment obtained by compacting a lime-treated clayey soil. A comprehensive test programme was carried out in order to highlight the improvement of mechanical behaviour induced by lime treatment as well as to assess the durability of the improved material, which may be affected by severe seasonal wetting and drying cycles. Direct shear tests, triaxial compression tests, swelling potential measurement and oedometric tests were performed on samples cured in controlled environmental conditions for at least 18 months. Wetting and drying cycles were applied in a very wide range of suction valu…
Effect of some injection molding processing conditions on weld lines characteristics
1988
The influence of injection and mold temperature as well as holding time on the knit-line characteristics in samples of Nylon 6 obtained by injection molding was analysed. The characteristics of the surface defect seem to be governed by the shrinkage rate and amount in the weld line zone.
Large Photonic Films by Crystallization on Fluid Substrates
2002
Cracks, which appear due to shrinkage during drying of artificial opaline films, strongly limit the use of these materials. Crystallization on fluid substrates (liquid metals) is a way to circumvent this problem. By this method it is possible to prepare crack-free three-dimensional “monocrystals” with a very low defect density and the size in millimeters.
EFFECT OF SHAPE ON POTATO AND CAULIFLOWER SHRINKAGE DURING DRYING
2000
ABSTRACT Shrinkage of potato cubes, parallelepipeds and cylinders was addressed during drying. A basic methodology by using image analysis was set-up in order to measure and monitor geometrical changes along the drying process. Both measurements by image analysis and directly with a calliper were carried out. Results from both methods showed a good agreement with no bias. Particle shape was found to influence shrinkage in a different way according to the axis. In fact the larger dimension shrinks less than the shorter one. This could be linked to the influence of the core drying in shrinkage. Experiments were also carried out for cauliflower stems. The difference in shrinkage between direct…
A plasticity model for predicting the rheological behavior of paperboard
2017
The sorption of water into the paperboard exposes a container to reversible and irreversible deformations under relative humidity variations. In this study, an elasto-plastic material model is used to demonstrate how through-thickness dry solids content gradients can generate permanent in-plane strains in paperboard. The measurements presented in this paper indicate that in consecutive loading-unloading cycles, the yield stress either remains roughly constant or decreases, and an additional permanent set of strain is obtained even when the maximum tension of repetitions stays constant. Two modified approaches concerning elasto-plastic hardening behavior based on the measurements of this wor…