Search results for "sport"
showing 10 items of 11179 documents
Novel concept for stabilising a hydraulic circuit containing counterbalance valve and pressure compensated flow supply
2016
In this paper, a novel concept for stabilising a hydraulic system containing a counterbalance valve and a pressure compensated flow supply is presented. The concept utilizes a secondary circuit where a low-pass filtered value of the load pressure is generated and fed back to the compensator of the flow supply valve. The novel concept has been investigated theoretically and experimentally. A linear model has been developed to verify the improved stability conditions. The novel concept has been implemented on a single boom actuated by a cylinder. The results show that the pressure oscillations in an otherwise unstable system can be suppressed with the novel concept. This happens without any c…
On break-away forces in actuated motion systems with nonlinear friction
2017
The phenomenon of so-called break-away forces, as maximal actuation forces at which a sticking system begins to slide and thus passes over to a steady (macro) motion, is well known from engineering practice but still less understood in its cause-effect relationship. This note analyzes the break-away behavior of systems with nonlinear friction, which is analytically well-described by combining the Coulomb friction law with rate-independent presliding transitions and, when necessary, Stribeck effect of the velocity-weakening steady-state curve. The break-away conditions are harmonized with analytic form of the system description and shown to be in accord with a relationship between the varyin…
Surface and mechanical characterization of stationary shoulder friction stir welded lap joints: experimental and numerical approach
2020
Friction Stir Welding (FSW) is one of the most used solid-state welding processes in the aeronautical, aerospace, ground transportation and naval fields. Stationary Shoulder Friction Stir Welding (SSFSW) is a recently introduced variant of the process allowing lower heat input into the joints, with beneficial effects in terms of joint mechanical properties, microstructure and top surface finish. In the paper, lap joints produced by SSFSW and made out of AA6082-T6 aluminum alloy sheets have been analyzed with the aim to investigate the effect of the stationary shoulder on the lap joints surface, metallurgical, and mechanical properties. The lap joints produced by SSFSW have been compared to …
Frequency-domain experimental setup for mechatronic and suspension system components
2021
This paper presents a frequency-domain experimental setup for modal analysis of mechatronic and suspension system components. Design, instrumentation and dynamic behavior of the one degree-of-freedom (DOF) system, capable of providing both, periodic and application-specific, excitation forces is described. The excitation is realized by an electromagnetic modal shaker with additional assembly and interface components designed and instrumented for frequency -domain analysis of vertical dynamics. Frequency response functions (FRFs) of the implemented system are experimentally measured and the associated basic model parameters are calculated, correspondingly identified. Accurate fit between the…
Optimization of Vehicle-to-Vehicle Frontal Crash Model Based on Measured Data Using Genetic Algorithm
2017
In this paper, a mathematical model for vehicle-to-vehicle frontal crash is developed. The experimental data are taken from the National Highway Traffic Safety Administration. To model the crash scenario, the two vehicles are represented by two masses moving in opposite directions. The front structures of the vehicles are modeled by Kelvin elements, consisting of springs and dampers in parallel, and estimated as piecewise linear functions of displacements and velocities, respectively. To estimate and optimize the model parameters, a genetic algorithm approach is proposed. Finally, it is observed that the developed model can accurately reproduce the real kinematic results from the crash test…
Flow Control of Fluid in Pipelines Using PID Controller
2019
In this paper, a PID controller is utilized in order to control the flow rate of the heavy oil in pipelines by controlling the vibration in a motor pump. A torsional actuator is placed on the motor pump in order to control the vibration on a motor and consequently controlling the flow rates in pipelines. The necessary conditions for the asymptotic stability of the proposed controller are validated by implementing the Lyapunov stability theorem. The theoretical concepts are validated utilizing numerical simulations and analysis, which proves the effectiveness of the PID controller in the control of flow rates in pipelines.
Power losses in power-split CVTs: A fast black-box approximate method
2018
Abstract This paper addresses the mechanical losses of planetary transmissions, with particular attention to power-split CVTs in their hybrid electric versions. It provides unified layout-independent analytical relationships, which can be used for both analysis, design and control purposes, and a simplified approach; the latter overcomes the necessity to segment the operating range of the power-split CVT in order to keep its loss model physically consistent. An example of application to a real hybrid electric PS-CVT is performed to show the simplicity, accuracy and generality of the proposed method.
Preventing the oil film instability in rotor-dynamics
2016
Horizontal rotor systems on lubricated journal bearings may incur instability risks depending on the load and the angular speed. The instability is associated with the asymmetry of the stiffness matrix of the bearings around the equilibrium position, in like manner as the internal hysteretic instability somehow, where some beneficial effect is indeed obtainable by an anisotropic configuration of the support stiffness. Hence, the idea of the present analysis is to check if similar advantages are also obtainable towards the oil film instability. The instability thresholds are calculated by usual methods, such as the Routh criterion or the direct search for the system eigenvalues. The results …
Using infrared thermography in order to compare laser and hybrid (laser plus MIG) welding processes
2009
International audience; In order to deepen the understanding of the differences between laser and laser-arc hybrid welding, comparisons were undertaken using thermography. The experiments were carried out for a T assembly of aluminium alloy plates. Modelling, based on the finite element method approach, was realized using IR temperature measurements and seam geometry. For a value of the power supply, depicted as a surface source in the hybrid case, agreement was found between simulated and measured temperatures. The arc power supply efficiency value is similar to the usually used value.
Axial Load Capacity of Cold Formed Pipe Flange Connection
2017
In this paper, a cold forming process is used where the connection between a pipe and a flange is created by means of radially expanding tool segments inside the pipe. The method is investigated with two purposes, to set up a robust procedure for the process that allows for connections to be made on site, and to set up finite element (FE) simulations that can capture the forces and deformations when pulling the pipe axially out of the flange. Experimental data and FE simulations are used to describe and understand the forces and deformations during the connection process. The rapid increase in radial stiffness experienced when the pipe comes in full circumferential contact with the flange i…