Search results for "strength"
showing 10 items of 2415 documents
Risk of failure in existing RC balcony and strength verification under degradation phenomena
2020
Abstract In the present paper, the safety conditions of reinforced concrete (RC) balconies subject to degradation phenomena caused by carbonation, presence of chlorides or water infiltration were examined. After a brief review of the typical damages of balconies occurring with detachments of plaster and bricks expulsion, some cases of collapses of balconies recently occurred were presented. Therefore, a calculation model was proposed for a hand verification of the flexural and shear strength of existing corroded T beams cast in place of lightened RC orthotropic slabs forming the balcony and for the calculus of deflection including slippage of steel bars. Diffused and pitting corrosion on st…
The effect of surface treatment with Er: YAG laser on shear bond strength of orthodontic brackets to fiber-reinforced composite
2014
Objectives: This study aimed to investigate the effect of surface treatment with Er:YAG laser on shear bond strength (SBS) of orthodontic brackets to fiber-reinforced composite (FRC). Study Design: Ninety human premolars were randomly divided into six groups of 15. FRC bars were bonded to the teeth with a flowable composite (FC) and then underwent following treatments. In group 1 no further treatment was performed. In group 2 the FRC surfaces were covered by FC. An Er:YAG laser was employed to treat FRCs in groups 3 ( 200 mJ/10 Hz) and 4 (300 mJ/15 Hz). The FRC strips in groups 5 and 6 were first covered by FC and then irradiated with Er:YAG laser at 200 mJ/10 Hz (group 5) or 300 mJ/15 Hz (…
Experimental in situ behaviour of unreinforced masonry elements retrofitted by pre-tensioned stainless steel ribbons
2014
Abstract The results of in situ tests carried out on unreinforced and reinforced poor rubble masonry full-scale walls in the earthquake prone Messina (Italy) area are presented and discussed. This experimental research was aimed at the assessment of the in plane shear behaviour of ancient masonry strengthened with an innovative system for masonry and retrofitting of reinforced concrete element constituted by three-dimensional pre-tensioned stainless steel ribbons. A comparison between different strengthening configurations was made in order to characterise the behaviour of masonry panels under shear-compression load, focusing attention on the diagonal cracking failure mode. The effectivenes…
Integrated ternary bionanocomposites with superior mechanical performance via the synergistic role of graphene and plasma treated carbon nanotubes
2019
Abstract Herein, we prepared an integrated ternary bionanocomposite based on polylactic acid (PLA) as a host polymer and two different forms of carbon fillers, i.e. graphene nanoplatelets (GNPs) and carbon nanotubes (CNTs), used simultaneously at extremely low concentrations, relying on the synergistic effect of CNT and graphene nanoreinforcement and a novel, multi-step procedure to achieve a high level dispersion. The results indicated that this multi-step approach allows stiffness increments up to +66%, with simultaneous enhancement of tensile strength (up to +44%), and elongation at break (up to +36%) with respect to neat PLA, by adding an extremely low content (0.5 wt%) of a hybrid comb…
Improvements in aggregate-paste interface by the hydration of steelmaking waste in concretes and mortars
2019
[EN] The objective of the experimental work is to study the mechanical properties in self-compacting concretes (SCC) in which part of the limestone aggregate has been replaced by granulated blast furnace slag (GBFS) in different percentages ranging from 0% to 60%. The results show that at early ages the SCC with the largest content in slag tend to have lower compressive strengths due to the poor compacting of the aggregates, although in the long-term their strength increases due to the reactivity of the slag. In fact, at the age of 365 days, the mortars made with the substitution of 50% of cement by ground GBFS reach compressive strength similar to that of the mortar made with 100% of cemen…
Effect of cobalt doping on the mechanical properties of ZnO nanowires
2016
Abstract In this work, we investigate the influence of doping on the mechanical properties of ZnO nanowires (NWs) by comparing the mechanical properties of pure and Co-doped ZnO NWs grown in similar conditions and having the same crystallographic orientation [0001]. The mechanical characterization included three-point bending tests made with atomic force microscopy and cantilever beam bending tests performed inside scanning electron microscopy. It was found that the Young's modulus of ZnO NWs containing 5% of Co was approximately a third lower than that of the pure ZnO NWs. Bending strength values were comparable for both materials and in both cases were close to theoretical strength indica…
Mechanical properties of sol–gel derived SiO2 nanotubes
2014
The mechanical properties of thick-walled SiO2 nanotubes (NTs) prepared by a sol–gel method while using Ag nanowires (NWs) as templates were measured by using different methods. In situ scanning electron microscopy (SEM) cantilever beam bending tests were carried out by using a nanomanipulator equipped with a force sensor in order to investigate plasticity and flexural response of NTs. Nanoindentation and three point bending tests of NTs were performed by atomic force microscopy (AFM) under ambient conditions. Half-suspended and three-point bending tests were processed in the framework of linear elasticity theory. Finite element method simulations were used to extract Young’s modulus values…
Sensing of the Molecular Spin in Spin-Crossover Nanoparticles with Micromechanical Resonators
2019
In the past years, the use of highly sensitive silicon microelectromechanical cantilevers has been proposed as a tool to characterize the spin-crossover phenomenon by employing fast optical readout of the motion. In this work, Fe II -based spin-crossover nanoparticles of the well-known [Fe(Htrz) 2 (trz)](BF 4 ) complex wrapped with thin silica shells of different sizes will be studied by means of silicon microresonators. The silica shell will enhance its chemical stability, whereas the low thickness will allow a proper mechanical coupling between the cantilever and the spin-crossover core. To maximize the sensing of the spin-crossover phenomena, different cantilever geometries and flexural…
Heterogeneous crystallization of zinc hydroxystannate on galvanized steel for enhancing the bond strength at the rebar/concrete interface
2021
Abstract Zinc hydroxystannate (ZnSn(OH)6) coatings were deposited on galvanized carbon steel samples by an electroless heterogeneous crystallization process. Structural and morphological features of the coatings as a function of the immersion time were determined by X-ray diffraction, Raman Spectroscopy and Scanning Electron Microscopy revealing the presence of truncated octahedrons of crystalline ZnSn(OH)6. Electrochemical characterization in a simulated concrete pore solution without and with addition of chloride ions proved that the cathodic protection is preserved and that ZnSn(OH)6 improved the corrosion resistance of the rebars. Pull-out tests demonstrated an enhanced bond strength at…
Physical activation and characterization of tannin-based foams enforced with boric acid and zinc chloride
2019
In this study, tannin-furanic-based foams enforced with H3BO3 and ZnCl2 are investigated, as well as their properties such as mechanical strength, specific surface area, and pore size distribution. From an industrial point of view, the aforementioned properties of these foams play a key role when used as catalyst, adsorbent, or gas storing materials. Therefore, this study aims to prove that such enforced tannin-furanic foams are promising materials for these types of applications. According to the results, materials that are up to five times stronger can be achieved by carbonizing the foams in comparison to maturing them. With physical activation, it was possible to obtain a specific surfac…