Search results for "technical"

Testing slope effect on flow resistance equation for mobile bed rills

2018

In this paper, a recently theoretically deduced rill flow resistance equation, based on a power-velocity profile, is tested experimentally on plots of varying slopes in which mobile bed rills are incised. Initially, measurements of flow velocity, water depth, cross-sectional area, wetted perimeter and bed slope conducted in 106 reaches of rills incised on an experimental plot having a slope of 14% were used to calibrate the flow resistance equation. Then, the relationship between the velocity profile parameter Γ, the channel slope, and the flow Froude number, which was calibrated using the 106 rill reach data, was tested using measurements carried out in plots having slopes of 22% and 9%. …

Testing the Stage-Discharge Relationship in Sloping SMBF Flumes

2021

The Samani, Magallanez, Baiamonte, Ferro (SMBF) flume is a simple and inexpensive instrument for indirect discharge measurement that was originally proposed for use in a horizontal channel and then also applied in sloping channels. The contraction of the flow cross section, aimed at establishing a critical flow condition, is simply obtained by applying two half cylinders to the walls of a rectangular cross section. In this paper a theoretical approach previously proposed for a horizontal SMBF flume is first extended to a sloping SMBF flume and a new stage-discharge relationship is deduced. Then, this equation is experimentally tested using laboratory measurements from literature for differe…

Momentum transport and bed shear stress distribution in a meandering bend: Experimental analysis in a laboratory flume

2015

The paper concerns the mechanisms underlying the distribution of the bed shear stress in meandering bends. Literature indicates that cross-stream circulation strongly affects the redistribution of the downstream velocity, but the feedback between them is still poorly understood. The aim of this paper is to gain some insight into how the momentum transport by cross-stream circulation contributes to the bed shear stress redistribution. Experimental analysis, based on a detailed dataset collected in a large-amplitude meandering laboratory flume, is presented. From these data an evaluation is made of the terms in the depth-averaged momentum equations and the analysis is especially devoted to te…

Simultaneous Flow over and under a Gate

2000

This paper reports the results of an investigation carried out to establish the stage-discharge relationship for a flow simultaneously discharging over and under a sluice or a broad-crested gate. The stage-discharge relationship is deduced by a theoretical analysis, based on the application of the Π-theorem of the dimensional analysis and the incomplete self-similarity theory, coupled with an experimental investigation carried out by using a laboratory flume.

Fracture and vein patterns as indicators of deformation history: a numerical study

2005

A technical note on an experimental device to measure friction coefficient in sheet metal forming

2006

Abstract In the paper the authors present the results of several experimental tests aimed to determine the Coulomb friction coefficient in sheet metal forming operations at the varying of the sheet metal material and for different operative conditions. In particular a few pressure and lubricating conditions have been investigated. In order to develop such experiments a dedicated fixture was designed and set-up starting from the one proposed by Wilson.

Experimental and Numerical Study on the Flow Field and Friction Factor in a Pressurized Corrugated Pipe

2015

An experimental campaign including measurement of pressure drops and velocity profiles was conducted on the pressurized flow in a commercial corrugated pipe. The results show that the empirical graphs suggested by Morris in the fifties may produce inaccurate assessments of the friction factor, in particular, for low Reynolds numbers. The experimental data was then reproduced by means of a numerical model with the large eddy simulation (LES) technique. The friction factor behavior for low and relatively high Reynolds numbers was thus investigated. The numerical simulations were in good agreement with the experimental results, showing the LES suitability to predict the effect of the pipe wall…

Analysis of Geometrical Relationships and Friction Losses in Small-Diameter Lay-Flat Polyethylene Pipes

2016

[EN] The use of lay-flat polyethylene pipes to irrigate horticultural crops has been receiving widespread attention in the last decade, due to the significant improvements in their hydraulic performance, their potentially high application efficiency, and their limited installation costs. However, even if hydraulic design procedures for conventional microirrigation systems are fairly well established, there is still the need to know how different pipe-wall thicknesses of lay-flat pipes can affect the pipe geometry under different operating pressures as well as the related consequences on friction losses. This paper, after comparing two different procedures (caliper and photographic) to asses…

Technology Assessment of Socio-Technical Futures: A Discussion Paper

2019

Problem: Visions of technology, future scenarios, guiding visions (Leitbilder) represent imaginations of future states of affairs that play a functional role in processes of technological research, development and innovation—e.g. as a means to create attention, communication, coordination, or for the strategic exertion of influence. Since a couple of years there is a growing attention for such imaginations of futures in politics, the economy, research and the civil society. This trend concerns technology assessment (TA) as an observer of these processes and a consultant on the implications of technology and innovation. TA faces increasing demands to assess imaginations of futures that circu…

Improving accuracy of the intermediate splint in substantial intermaxillary sagittal discrepancies using an extra anterior anchorage point: technical…

2021

Background To describe a technical feature that increases the stability of the intermediate splint in patients where bimaxillary surgery with great maxillary/mandibular advancements are planned. Material and Methods Prospective evaluation of the intermediate splint dental vertical penetration in patients undergoing bimaxillary surgery where great sagittal discrepancy occur in the anterior sector between the upper and lower jaws when the intermediate splint is placed by adding an extra intermaxillary fixation (IMF) screw (2x9 mm) placed between the central incisors of the maxilla and fixed to the most anterior aspect of the intermediate splint following the direction of the sagittal maxillo-…