Search results for "testing."
showing 10 items of 1654 documents
Application of DNA techniques for identification using human dental pulp as a source of DNA
1992
Dental pulp tissue could be obtained in most cases from materials obtained under experimental conditions and from forensic casework (air accidents, burned and putrefied bodies). Teeth extracted during dental treatment (n = 30) were stored for 6 weeks and 4 years at room temperature. In addition teeth (n = 10) extracted from jaw fragments that had been stored for 15 years at room temperature, and teeth extracted post mortem from actual identification cases (n = 8) were investigated. Following extraction from dental pulp tissue the DNA concentration was measured by fluorometry. The amount of DNA obtained from the dental pulp tissue of a single tooth varied from 6 micrograms to 50 micrograms D…
Experimental Studies Regarding the Mechanical Behaviour of Silicon-Coated and Uncoated P.A. 6.6 Fabrics
2014
These paper aims to present an experimental study for determining the mechanical properties of woven fabrics used for airbags manufacturing. In order to realise the study, there were chosen two types of fabric, one that is coated with silicon and one that is uncoated. The experimental tests that were carried out were uniaxial tension tests for samples extracted on the warp and on the weft direction, the Bias test, a test specific for shear loads and the dome test, a test specific for biaxial loads. For the uniaxial tension test the force-displacement curve was obtained and the maximum values of the loads and the displacement. For the last two tests (bias test and dome test) there have been …
An in vitro evaluation of the effect of sandblasting and laser surface treatment on the shear bond strength of a composite resin to the facial surfac…
2015
Objectives: The present study was conducted to evaluate the optimal method of enhancing the bond strength of a composite resin to the facial surface of the primary anterior stainless steel crowns using various surface treatments namely Nd: YAG laser surface treatment, sandblasting , alloy primer application and no surface treatment. Study Design: The study sample consisted of 60 primary anterior stainless steel crowns (UnitekTM size R 4), with 15 samples randomly divided into the 4 study groups, embedded in acrylic blocks. The facial surface of these surface treated crowns was utilized as the bonding surface to which 2.5mm diameter composite resin cylinders were bonded for the evaluation of…
Two Patients With History of STEC-HUS, Posttransplant Recurrence and Complement Gene Mutations
2013
Hemolytic uremic syndrome (HUS) is a disease of microangiopathic hemolytic anemia, thrombocytopenia and acute renal failure. About 90% of cases are secondary to infections by Escherichia coli strains producing Shiga-like toxins (STEC-HUS), while 10% are associated with mutations in genes encoding proteins of complement system (aHUS). We describe two patients with a clinical history of STEC-HUS, who developed end-stage renal disease (ESRD) soon after disease onset. They received a kidney transplant but lost the graft for HUS recurrence, a complication more commonly observed in aHUS. Before planning a second renal transplantation, the two patients underwent genetic screening for aHUS-associat…
SIGNAL ANALYSIS AND PERFORMANCE EVALUATION OF A VEHICLE CRASH TEST WITH A FIXED SAFETY BARRIER BASED ON HAAR WAVELETS
2011
Author's version of an article published in the journal: International Journal of Wavelets, Multiresolution and Information Processing. Also available from the publisher at: http://dx.doi.org/10.1142/s0219691311003979 This paper deals with the wavelet-based performance analysis of the safety barrier for use in a full-scale test. The test involves a vehicle, a Ford Fiesta, which strikes the safety barrier at a prescribed angle and speed. The vehicle speed before the collision was measured. Vehicle accelerations in three directions at the center of gravity were measured during the collision. The yaw rate was measured with a gyro meter. Using normal speed and high-speed video cameras, the beha…
Lock-In Signal Post-Processing Techniques in Infra-Red Thermography for Materials Structural Evaluation
2013
This paper describes the potential of off-line thermographic signal processing by means of Lock-In Correlation algorithms, in order to implement structural health monitoring and stress analysis techniques. Thermal datasets acquired by infrared thermocameras are locked-in and correlated numerically with opportune reference signals, and amplitude and phase values of various harmonics retrieved by means of a Fast Fourier Transform and time averaging based filtering. This information is then processed for NDT defect probing and for evaluating the Thermoelastic Effect induced temperature changes. Two case studies in particular are discussed, implementing the proposed signal lock-in processing: a…
Quantitative thermoelastic stress analysis by means of low-cost setups
2020
Abstract A low-cost Thermoelastic Stress Analysis (TSA) experimental setup is proposed which uses an ordinary micro-bolometer and in-house developed signal processing scripts. The setup is evaluated by analysing the thermoelastic signal from a tensile and a SENT specimen made of stainless steel AISI 304L, and the bolometer performances are compared with those of a state of the art photon detector. Signal processing is based on off-line cross-correlation, using a self-reference signal which is retrieved from the acquired thermal data. Procedures are in particular developed to recognise, quantify and correct errors due to spectral leakage and loss of streamed frames. The thermoelastic signal …
Surface AFM microscopy of unworn and worn samples of silicone hydrogel contact lenses
2008
Abstract: Purpose. To evaluate the qualitative and quantitative topographic changes in the surface of worn contact lenses (CLs) of different materials using atomic force microscopy (AFM). Methods. The topography of five different CL materials was evaluated withAFM over a surface of 25 lm2 according to previously published experimental setup. Average roughness (Ra) and root mean square (Rms) values were obtained for unworn and worn samples. Results. The Ra value increased for balafilcon A (11.62–13.68 nm for unworn and worn samples, respectively), lotrafilcon A (3.67–15.01 nm for unworn and worn samples, respectively), lotrafilcon B (4.08–8.42 nm for unworn and worn samples, respectively), g…
Plasmonic Focusing Reduces Ensemble Linewidth of Silver-Coated Gold Nanorods
2008
Silver coating gold nanorods reduces the ensemble plasmon line width by changing the relation connecting particle shape and plasmon resonance wavelength. This change, we term "plasmonic focusing", leads to less variation of resonance wavelengths for the same particle size distribution. We also find smaller single particle linewidth comparing resonances at the same wavelength but show that this does not contribute to the ensemble linewidth narrowing.
Effect of surface treatment with sandblasting and Er,Cr:YSGG laser on bonding of stainless steel orthodontic brackets to silver amalgam
2011
Objectives: Satisfactory bonding of orthodontic attachments to amalgam is a challenge for orthodontists. The aim of this in vitro study was to compare the shear bond strength of stainless steel orthodontic brackets to silver amalgam treated with sandblasting and Er,Cr:YSGG laser. Study Design: Fifty-four amalgam discs were prepared, polished and divided into three groups: In group 1 (the control group) the premolar brackets were bonded using Panavia F resin cement without any surface treatment; in groups 2 and 3, the specimens were subjected to sandblasting and Er,Cr:YSGG laser respectively, before bracket bonding. After immersing in distilled water at 37°C for 24 hours, all the specimens w…