Search results for "thermal treatment"
showing 10 items of 146 documents
Tuning the Properties of Photonic Films from Polymer Beads by Chemistry
2002
This paper describes the preparation of monodisperse colloids from various methacrylates. These colloids sediment well on glass slides and formin the dried statelarge three-dimensional face-centered cubic photonic crystal films with Bragg reflection in the visible region. Depending on crystallization conditions, the domain sizes vary between 50 and 300 μm. By cross-linking the polymer within the colloids, it is possible to increase the thermal stability of the polymeric photonic structure tremendously (up to 1 h at 200 °C). These photonic structures soften above Tg (rubbery photonic structure), but they cannot fuse. Cross-linked colloids from poly(tert-butyl methacrylate) can either thermal…
Effect of irradiation temperature and dose rate on the mechanical tensile behaviour of low density polyethylene
1993
Abstract The effect of ageing due to gamma radiation, at various dose rates and temperatures, on the mechanical tensile behaviour of low density polyethylene is studied. In order to detect synergistic effects, tensile tests on samples subjected to thermal treatment corresponding to the same temperature for the same time as for the irradiation tests have also been performed. The results indicate a generalized decrease of the elongation at break, with brittleness of the material for the most severe ageing treatments. For modulus values, an increase is observed for particular experimental conditions. These results are related to morphological and structural modifications induced in the polymer…
Hydrothermal ageing of radiation cured epoxy resin-polyether sulfone blends as matrices for structural composites
2010
Abstract The hydrothermal ageing of epoxy–thermoplastic blends, used as matrices for carbon fibre composites, cured by electron beam, has been studied. Two different thermoplastic percentages have been adopted. A suitable choice of both curing process and formulation parameters allows to carry out irradiation at mild temperature with several advantages, coming from a “non thermal” process, for both the final properties of the materials and the environment. Nevertheless the occurring of vitrification phenomena needs the use of a short thermal treatment after irradiation on the already solid materials, in order to complete the cure reactions. Radiation cured epoxy based matrices have been sub…
Gamma-radiation ageing of a low density polyethylene. Effects of irradiation temperature and dose rate
1993
Abstract Ageing due to gamma radiation of a low density polyethylene at various dose rates and temperatures is studied; the effect of thermal treatment only is also considered. The modifications induced in the molecular and crystallinity behaviour of the polymer are investigated by means of gel extraction, measurements of intrinsic viscosity and thermal analysis. Results indicate the occurrence of both crosslinking and oxidative degradation; the extent of the latter increases on decreasing the irradiation dose rate and on increasing the irradiation temperature. Some exceptions are found because of the increase in the mobility of free radicals at high temperature. These effects modify also t…
E-beam curing of epoxy based blends in order to produce high performance composites
2007
In this work, blends of a difunctional epoxy monomer and a thermoplastic toughening agent are E-beam irradiated at two different dose rates and two different total absorbed doses. The influence of the processing conditions on the thermal properties and on the morphology of the obtained matrices has been investigated. In particular, it is shown how the increase of the dose rate causes an increase of the temperature during irradiation, thus inducing a simultaneous thermal and radiation curing. On the contrary, at low-dose rate the system mainly undergoes to radiation curing, thus making the cured material very sensible to a post-irradiation thermal treatment with a significant improvement of …
Optical properties of lithium niobate single crystals
2005
Studies of thermal and γ-irradiation effects on the optical properties in congruous lithium niobate single crystals containing Y, Mg, Gd, B, and Zn dopants including samples with double dopants Y, Mg and Gd, Mg are reported. Formation of defects at irradiation and thermal treatment of the samples is explored by electron absorption spectra. Considerable increase of absorption with the dose of γ-radiation is observed at 500 nm. The changes of absorption examined under different conditions are explained by creation and destruction of Nb 4 + defects.
The influence of Fe3+ doping on thermally induced crystallization and phase evolution of amorphous calcium phosphate
2021
The present study investigates thermally induced crystallization and phase evolution of amorphous calcium phosphate (ACP) partially substituted with Fe3+ ions (M/P = 1.5 : 1). It was demonstrated that the presence of Fe3+ ions radically changes the crystallization behavior of ACP and completely prevents the formation of α-tricalcium phosphate (α-TCP, Ca3(PO4)2), which is the first crystalline phase obtained from non-substituted ACP upon thermal treatment. Surprisingly, calcium deficient hydroxyapatite (CDHA) was obtained instead of α-TCP. Such unusual crystallization behavior was observed with a doping level as low as 0.1 mol% with respect to Ca ions. Moreover, it was shown that the presenc…
Comparison of adsorption properties of commercial silica and rice husk ash (RHA) silica: A study by NIR spectroscopy
2021
Abstract Adsorption properties of Silica gel (commercial silica), rice husk ash (RHA) silica, and their hydrothermally treated products towards water molecules were studied in this work. RHA silica was prepared by heating rice husk to 650°C for 4 h after pretreatment with hydrochloric acid. Portions of the samples of silica were evacuated at 200℃ and then allowed to adsorb water molecules from the surrounding air at either 42 or 50% humidity. The near infrared spectra of these samples were measured at different time intervals during their adsorption of water molecules. The evolved near infrared spectra were analyzed using second derivative techniques. Adsorption properties of these samples …
Graphene oxide and Fumed silica graphene oxide nanocomposites modification by thermal treatments
2014
In the present study we investigate post synthesis thermal treatments up to 400 °C of graphene oxide (GrO) prepared from commercial graphite and of GrO–silica nanocomposites prepared by a solution of commercial Fumed silica nanoparticles (average diameter 7 nm or 40 nm) and the GrO. The thermal treatments were carried out in air, vacuum or He atmosphere to highlight tunable changes. Two GrO batches with small differences in the D (~1350 cm–1) and G (~1580 cm–1) Raman bands have been employed to evaluate effects depending on preparation. Thermal effects have been monitored through the Raman spectroscopy focusing on D, G and 2D (2500–3500 cm–1) bands spectral ranges. The experiments evidenced…
IMPROVED STABILITY OF GRAPHENE OXIDE-SILICA NANOHYBRIDS AND RELATED POLYMER-BASED NANOCOMPOSITES
2014
Although its promising properties make the graphene oxide (GO) very interesting as filler for polymer matrices, some problems related to its thermal stability in the region which ranges from 80 to 200 °C, are crucial for the possibility to melt process GO together with practically all the polymers [1,2]. Moreover, above 100 °C GO lamellae were found to become stacked. In this work, two different ways to preserve the GO structure and ensure its dispersion within different polymer matrices have been investigated and schematized in Fig. 1. Exfoliation plays a key-role in the achievement of good mechanical properties since it preserves the GO from both stacking phenomena. The capability of sili…