Search results for "turbine"
showing 10 items of 198 documents
In search for a canonical design ABL stability class for wind farm turbines
2016
Production as well as loading of wake exposed wind turbines is known to depend significantly on stability of the Atmospheric Boundary Layer (ABL), which adds a new dimension to design of wind farm turbines. Adding this new aspect in wind turbine design makes the number of design cycle computations to blow up with a factor equal to the number of representative stability bin classes. The research question to be answered in this paper is: Can an ABL stability probability distribution in a meaningful way be collapsed into a representative design stability class as based on a (predefined) confidence level.
WT Type 4 Benchmarks for IEC 61400-27-1
2019
Since several years there has been a constant effort at international level for the standardization and the validation of different types of wind turbine (WT) dynamic models. The paper focuses on the IEC 61400-27-1 type 4 model, proposing and fully describing two benchmark systems for the assessment of dynamic performance. The first system is a simple setup and it is designed to specifically assess the transient response of the WT controls. The second system is based on the IEEE 9-bus test system, and it is a multi-machine configuration allowing for the inclusion of the typical power system dynamics of synchronous machines and corresponding primary regulators. System configurations, models …
Inertial response of isolated power networks with wind power plants
2019
The constant increase of power generation provided by renewable energy source (RES) power plants is causing a progressive reduction of the overall inertia of the power systems. Especially in the case of small, isolated power networks, the replacement of conventional generation plants with RES power plants can affect significantly the frequency response of the system. The critical low-inertia conditions can be improved by the introduction of specific additional controls to the RES power converters. These control schemes are known as “synthetic inertia” or “virtual inertia” controls. The paper analyzes the impact of a derivative-based inertial control on a small, isolated power system, with a…
A sizing approach for stand-alone hybrid photovoltaic-wind-battery systems: A Sicilian case study
2018
Abstract Solar and wind energy are the two most available renewable energy resources in the world. In this paper, a high-resolution analysis that allows sizing a hybrid photovoltaic-wind turbine-battery banks has been carried out. The analysis aims to minimize the annualized cost of the systems satisfying two reliability constraints. The solution has been obtained numerically by means of an iterative technique. The decision variables are the photovoltaic area, wind turbine radius, and battery capacity. A high-resolution model, based on fuzzy logic inference system, has been developed to evaluate the number of active occupants and the domestic electricity consumption. In order to allow a mor…
Experimental and numerical investigation of the leading edge sweep angle effect on the performance of a delta blades hydrokinetic turbine
2020
Abstract In the last decades, an increase of energy consumption has been noted around the world. Hence, the excessive use of fossil fuels can lead to serious environmental concerns. Indeed, the use of renewable energy sources is needed to reduce the greenhouse gas effects and the CO2 emissions in the atmosphere. Small-scale hydropower could be an interesting and renewable alternative solution. The cross-flow turbines present several advantages compared to the axial-flow turbines. Therefore, increasing efforts are taken to enhance the efficiency and extend the applicability of the cross-flow turbines. In this paper, experimental investigation was carried out to evaluate the performance of a …
Comparison of numerical modelling techniques for impact investigation on a wind turbine blade
2019
Wind turbine blades are exposed to numerous impact risks throughout their lifetimes. The impact risks range from bird collisions during operation to impacts with surrounding structures at the time of transportation and installation. Impact loads on the fibre composite blades can induce several complex, simultaneously interacting and visually undetectable damage modes and have a high potential to reduce the local and global blade stiffness. An assessment of such impact-induced damages is therefore necessary and usually involves high computational costs using numerical procedures, especially when analysing large composite components. To minimise this computational expense, different numerical…
Minimum Leading Edge Protection Application Length to Combat Rain-Induced Erosion of Wind Turbine Blades
2021
Leading edge erosion (LEE) repairs of wind turbine blades (WTBs) involve infield application of leading edge protection (LEP) solutions. The industry is currently aiming to use factory based LEP coatings that can applied to the WTBs before they are shipped out for installation. However, one of the main challenges related to these solutions is the choice of a minimum LEP application length to be applied in the spanwise direction of the WTBs. Generally, coating suppliers apply 10–20 m of LEP onto the blades starting from the tip of the blade using the “rule of thumb”, and no studies in the literature exist that stipulate how these LEP lengths can be calculated. In this study, we extend the sc…
Effects of Onshore and Offshore Environmental Parameters on the Leading Edge Erosion of Wind Turbine Blades: A Comparative Study
2021
Abstract The presence of rain-induced leading edge erosion of wind turbine blades (WTBs) necessitates the development of erosion models. One of the essential parameters for erosion modeling is the relative impact velocity between rain droplets and the rotating blade. Based on this parameter, the erosion damage rate of a WTB is calculated to estimate the expected leading edge lifetime. The environmental conditions that govern this parameter have site-specific variations, and thus, rain and wind loading on a turbine differ for onshore and offshore locations. In addition, there are wave loads present in the offshore environment. The present paper tries to provide guidelines for erosion modelin…
Numerical investigation of rain droplet impact on offshore wind turbine blades under different rainfall conditions: A parametric study
2020
The leading edge of a fiber composite wind turbine blade (WTB) is prone to erosion damages due to repeated rain droplet impact during its service life. Such damages are critical to the blade's aerodynamic as well as structural performance, ultimately resulting in substantial repair costs. An effective design of a coating material for WTB is necessary and its analysis must include variables associated with erosive rain droplets such as (1) droplet diameter, (2) impact velocity, and (3) droplet impact angle. The present paper develops and validates a coupled fluid structure interaction (FSI) computational model for simulating rain droplet impact on WTBs, where the structure domain is modelled…
Leading Edge Erosion of Wind Turbine Blades: Effects of Environmental Parameters on Impact Velocities and Erosion Damage Rate
2021
Abstract Leading edge erosion (LEE) of a wind turbine blade (WTB) is a complex phenomenon that contributes to high operation and maintenance costs. The impact between rain droplets and rotating blades exerts cyclic fatigue stresses on the leading edge — causing progressive material loss and reduced aerodynamic performance. One of the most important parameters for erosion modelling and damage prediction is the relative impact velocity between rain droplets and rotating blade and depends upon the environmental conditions. The environmental condition, in general, could vary for onshore and offshore wind turbines (OWTs) — for instance, the presence of wave-induced loads along with less turbulen…