Search results for "visual_art"
showing 10 items of 2987 documents
WEAR PERFORMANCE OF CERAMIC CUTTING-TOOL MATERIALS WHEN CUTTING STEEL
1991
Abstract Some test cycles have been carried out in continuous cutting conditions, employing cutting parameters (feed, depth of cut and cutting speed) chosen following experimental planes and suitable test fields. The wear tests have been carried out on AISI 1040 steel with cutting speeds from 5m/sec to 11m/sec. The silicon nitride, sintered carbide, cubic boron nitride and alumina reinforced with SiC whiskers inserts, have shown, at each assigned cutting parameter, poor wear resistance when cutting steel. Alumina and alumina in submicron grain, which has been toughened by ZrO2 phase transformation, and the oxide-based alumina, have been the better wear resistance. The mixed based alumina ha…
Electropolishing of CuZn brasses and 316L stainless steels: Influence of alloy composition or preparation process (ALM vs. standard method)
2016
International audience; In the present paper, electropolishing behavior of different brass alloys (CuZn39Pb2, CuZn42) in phosphoric acid is studied to observe the impact of alloying elements on polishing quality. In the same way, the influence of the manufacturing process is also evaluated through the comparison of a “standard” stainless steel and a stainless steel prepared by Additive Laser Manufacturing (ALM). An electrochemical study was first performed to determine the best treatment conditions for each material/electrolyte pair and to study the electropolishing mechanism and its kinetic dependence on diffusion. Metallic samples are fully characterized before and after electropolishing …
One step continuous hydrothermal synthesis of very fine stabilized superparamagnetic nanoparticles of magnetite
2011
International audience; Stable suspensions of citrated SPIO nanoparticles were synthesised in one step using a hydrothermal continuous process. Citrates control the crystallite size and the oxidation degree of metallic ions despite the very short reaction time (4 s). Magnetite particles, Fe2.94O4, with an average size of 4 nm and good monodispersity were obtained.
Determination of the residual stresses in composite laminate using the compliance method
2005
Residual stresses play an important role on the mechanical behavior of composite laminate. The development of new methods to determine the residual stresses gradient within the laminates is necessary. This article presents the adaptation of the compliance method in the case of composite laminates carbon/epoxy [02/902]s. The incremental drilling of a constant width groove allows for each increment to measure the strains (using strain gages) and displacements (using an optical device) of particularly points of the structure surface. These experimental data are compared with results given by a finite elements simulation. This comparison allows to raise the residual stresses in the composite la…
Implementation of eco-sustainable biocomposite materials reinforced by optimized agave fibers
2018
Abstract Although several works have recently been published in literature about biocomposites, i.e. about composites with polymeric matrix reinforced by natural fibers, only a few articles have been devoted to the implementation of high performance biocomposites for structural and semi-structural applications. The present study aims to give a contribution by considering biocomposites obtained by using an eco-friendly partially bio-based epoxy (green epoxy) and sisal (agave sisalana fibers) obtained by a proper optimization process. Through a systematic experimental analysis, three different types of biocomposites obtained with a suitable manufacturing process, such as random short fiber bi…
Static and dynamic mechanical properties of Arundo Donax fillers-epoxy composites
2014
Abstract Aim of this work is to investigate the feasibility of using a natural and inexpensive filler obtained by grinding the culms of Arundo Donax as reinforcement of epoxy resins. The effect of the content and size of Arundo Donax fillers on static and dynamic mechanical properties was evaluated showing that the composites exhibit higher tensile moduli, comparable flexural moduli and lower strength properties in comparison to the neat resin. Moreover, changes in the storage and the loss moduli only above the glass transition temperature (i.e. in the rubbery region) were found while neither significant shifts of tan δ peaks to higher temperatures nor reductions in the peak height of the c…
The effect of alkaline treatment on mechanical properties of kenaf fibers and their epoxy composites
2015
Abstract In this work, kenaf fibers were pre-treated in a NaOH solution (6% in weight) at room temperature for two different periods (48 and 144 h). The chemical treatment of kenaf fibers for 48 h allowed to clean their surface removing each impurity whereas 144 h of immersion time had detrimental effect on the fibers surface and, consequently, on their mechanical properties. Untreated and NaOH treated kenaf fibers (i.e. for 48 h) were also used as reinforcing agent of epoxy resin composites. The effect of the stacking sequence (i.e. using unidirectional long fibers or randomly oriented short fibers) and the chemical treatment on the static mechanical properties was evaluated showing that t…
Identification of overglaze and underglaze cobalt decoration of ceramics from Valencia(Spain) by portable EDXRF spectrometry
2004
The purpose of this work is the application of non-destructive analysis to differentiate underglaze and overglaze techniques used in the decoration of glazed ceramics from Valencia (Spain). This study was carried out by portable EDXRF spectrometry using an X-ray tube and a thermoelectrically cooled semiconductor detector. From the EDXRF spectra we have identified the main elements present in the tin-opacified lead glaze and in the cobalt pigments. The identification of the underglaze and overglaze decoration is based on the different ratios between the fluorescence line of the main component of the glaze (Pb-La line) and the fluorescence lines of the main components of the pigment (Co-Ka, M…
Iron Mineralogy of Venus' Surface Investigated by M�ssbauer Spectroscopy
2000
Abstract We discuss the use of Mossbauer (MB) spectroscopy to study Fe-bearing minerals on Venus' surface. At present, there is no direct information about the mineralogy of Venus' surface, although in situ chemical analyses by X-ray fluorescence (XRF) spectroscopy have been done by the Venera 13, 14, and Vega 2 spacecraft at three landing sites. The XRF elemental analyses are sensitive to major rock-forming elements heavier than sodium and show the presence of several mass percent iron. Normative mineralogical calculations model the Fe mineralogy at the Venera 13, 14, and Vega 2 landing sites, but the actual Fe minerals present are unknown. We calculate synthetic MB spectra for the normati…
Semiconductor-metal transitions in liquidIn100−xSexalloys: A concentration-induced transition
2004
The electronic and structural properties of ${\mathrm{In}}_{100\ensuremath{-}x}{\mathrm{Se}}_{x}$ liquid alloys close to their melting points have been investigated by combining x-ray-absorption experiments with ab initio molecular-dynamics simulations. Extended x-ray-absorption fine-structure data have been acquired at both the In and Se K edges in a large concentration range $(x=20%$ to $x=50%$ of Se content). Ab initio molecular-dynamics simulations have been carried out at the two most extreme concentrations explored experimentally. Liquid InSe is found to retain a semiconducting behavior which results from a low-dimensional structure, reminiscent of that of the ambient solid phase, cha…