showing 10 related works from this author
Static Deflection Compensation of Multi-Link Flexible Manipulators Under Gravity
2022
The static deflection compensation method of a planar multi-link flexible manipulator is proposed using the feedback from inertial sensors mounted at the tip of each link. The proposed compensation technique is validated experimentally using a high-precision laser tracker. The proposed strategy is experimentally verified using a three-link flexible manipulator. A strategy to compensate for the centripetal and tangential acceleration induced on the accelerometer mounted on the rotating link is proposed for correct inclination estimation. The improvement in the inclination estimation using the proposed compensation technique is verified both in simulation and experimental studies.
Camera-LiDAR Data Fusion for Autonomous Mooring Operation
2020
Author's accepted manuscript. © 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. The use of camera and LiDAR sensors to sense the environment has gained increasing popularity in robotics. Individual sensors, such as cameras and LiDARs, fail to meet the growing challenges in complex autonomous systems. One such scenario is autonomous mooring, where the ship has to …
Autonomous Mooring towards Autonomous Maritime Navigation and Offshore Operations
2020
Bollard is a vital component of mooring system. It is the anchor point for mooring ropes to be fixed in order to secure the vessel or ship. An algorithm that translates the segmented mask of bollard output from masked R-CNN along with bounding box and associated class probability to its corresponding edge coordinate and finally to the single reference point for efficient detection and classification of bollard towards autonomous mooring is presented. At first stage, Mask R-CNN framework is trained with custom built bollard. The model obtained from the training is inferred with real data resulting in instance segment of bollard. The segmented mask obtained contains relatively large amount of…
UJI RobInLab's approach to the Amazon Robotics Challenge 2017
2017
This paper describes the approach taken by the team from the Robotic Intelligence Laboratory at Jaume I University to the Amazon Robotics Challenge 2017. The goal of the challenge is to automate pick and place operations in unstructured environments, specifically the shelves in an Amazon warehouse. RobInLab's approach is based on a Baxter Research robot and a customized storage system. The system's modular architecture, based on ROS, allows communication between two computers, two Arduinos and the Baxter. It integrates 9 hardware components along with 10 different algorithms to accomplish the pick and stow tasks. We describe the main components and pipelines of the system, along with some e…
Dynamic Modeling of Planar Multi-Link Flexible Manipulators
2021
A closed-form dynamic model of the planar multi-link flexible manipulator is presented. The assumed modes method is used with the Lagrangian formulation to obtain the dynamic equations of motion. Explicit equations of motion are derived for a three-link case assuming two modes of vibration for each link. The eigenvalue problem associated with the mass boundary conditions, which changes with the robot configuration and payload, is discussed. The time-domain simulation results and frequency-domain analysis of the dynamic model are presented to show the validity of the theoretical derivation.
Review on Modeling and Control of Flexible Link Manipulators
2020
This paper presents a review of dynamic modeling techniques and various control schemes to control flexible link manipulators (FLMs) that were studied in recent literature. The advantages and complexities associated with the FLMs are discussed briefly. A survey of the reported studies is carried out based on the method used for modeling link flexibility and obtaining equations of motion of the FLMs. The control techniques are reviewed by classifying them into two main categories: model-based and model-free control schemes. The merits and limitations of different modeling and control methods are highlighted.
Reshaping Field of View and Resolution with Segmented Reflectors: Bridging the Gap between Rotating and Solid-State LiDARs
2020
This paper describes the first simulations and experimental results of a novel segmented Light Detection And Ranging (LiDAR) reflector. Large portions of the rotating LiDAR data are typically discarded due to occlusion or a misplaced field of view (FOV). The proposed reflector solves this problem by reflecting the entire FOV of the rotating LiDAR towards a target. Optical simulation results, using Zemax OpticStudio, suggest that adding a reflector reduces the range of the embedded LiDAR with only 3 . 9 . Furthermore, pattern simulation results show that a radially reshaped FOV can be configured to maximize point cloud density, maximize coverage, or a combination. Here, the maximum density i…
Control of Redundant Flexible Manipulators with Redundancy Resolution
2022
Author's accepted manuscript. © 2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. This paper deals with the online control of a redundant flexible link manipulator to achieve minimum oscillations using the redundancy resolution technique. Different redundancy resolution techniques proposed and used for rigid link manipulators are tested for their use in the case of…
Modeling and Analysis of Flexible Bodies Using Lumped Parameter Method
2020
The modeling, identification and analysis of a flexible beam is presented. The lumped parameter method is used to model a flexible beam. The use of camera measurements to identify lumped parameters, namely spring stiffness and damping coefficient, is described. The measurements of the tip oscillations using a high-speed camera and high-precision laser tracker are compared. The static and dynamic behavior of the flexible beam model is compared to the experimental results to show the validity of the model.
Modeling and Control of Flexible Link Manipulators
2022
Autonomous maritime navigation and offshore operations have gained wide attention with the aim of reducing operational costs and increasing reliability and safety. Offshore operations, such as wind farm inspection, sea farm cleaning, and ship mooring, could be carried out autonomously or semi-autonomously by mounting one or more long-reach robots on the ship/vessel. In addition to offshore applications, long-reach manipulators can be used in many other engineering applications such as construction automation, aerospace industry, and space research. Some applications require the design of long and slender mechanical structures, which possess some degrees of flexibility and deflections becaus…