0000000000017201
AUTHOR
Ricardo Duchowicz
Q-switching of an erbium-doped fibre laser modulated by a Bragg grating fixed to a piezoelectric
The performance of the Q-switched erbium-doped fibre laser with two fibre Bragg gratings as cavity mirrors was theoretically analysed, employing a set of rate equations for the ion populations and the photon flux inside the cavity. The simulation considers a system where the pulsed laser emission is produced by the temporal modulation of a Bragg grating fixed to a piezoelectric and operating in the 1550 nm spectral region. The temporal evolution of different frequency components of the laser emission produced is governed by the instantaneous overlap between the two gratings. Theoretical results are in agreement with previously reported experimental values.
Determination of the position of defects generated within a chirped fiber Bragg grating by analyzing its reflection spectrum and group delay
We determinate the position of defects generated within a chirped fiber Bragg grating by analyzing its reflection spectrum and group delay. Simulations were performed by using the T-matrix method for different defect locations.
Development and analysis of a model based on chirped fiber Bragg gratings employed for cracks characterization in materials
In this work a model was developed that allows to understand the behavior of a chirped fiber Bragg grating for the detection and characterization of cracks in materials. In addition to the amplitude response, we show that the group delay of the grating provides useful information for the characterization of the crack. The position of the crack can be determined thanks to the linear chirp of the grating that fixes a correlation between the spatial position and both, the wavelength and the group delay. However, our analysis shows that this simple approach has a source of error, which can be overcome if a controllable external strain can be applied to the embedded grating, additional to the st…
Simple high-resolution wavelength monitor based on a fiber Bragg grating
A compact and low-cost device for monitoring the peak wavelength of single-peak spectral distributions is presented. The system is based on the transmission properties of a fiber Bragg grating when its period is modulated. Different types of optical signal, such as the emission of distributed-feedback lasers and the reflection of a broadband optical source produced by fiber gratings used in sensor systems, can be measured with this device. We demonstrate that a high wavelength resolution of micro 1 pm can be achieved and that our proposal can be used for real-time monitoring.
Fractional Fourier transform dual random phase encoding of time-varying signals
Optical techniques have shown great potential in the field of information security to encode high-security images. Among several established methods, a double-random phase encryption technique (DRPE) for encoding a primary image into stationary white noise was developed by using the analogy between Fresnel diffraction patterns and the fractional Fourier transform (FrFT-DRPE). In this case, additional keys are obtained through the knowledge of the fractional orders of the FrFTs. In this work we propose an encoding setup for time-varying signals, mainly for short-haul fiber optics link applications, that can be considered as the temporal analogue of the spatial FrFT-DRPE. The behavior of the …
All-fiber actively Q-switched Yb-doped laser
Abstract An all-fiber actively Q-switched Yb-doped laser is presented. Q-switching is performed by modulating a fiber Bragg grating via a magnetostrictive rod which is fixed to the fiber at the position of the grating. By exposing the rod to a changing magnetic field, the rod is stretched and relaxed causing the Bragg wavelength of the grating to shift and thereby changes the Q-factor of the cavity. Using Yb-doped fiber, pulses at 1052 nm are obtained at repetition rates from 1 to 200 kHz. At 75 kHz, 0.5 μJ pulses with peak powers of 3 W can be produced when 180 mW of pump power is applied. To the knowledge of the authors, this is the first all-fiber actively Q-switched Yb-doped laser prese…
High-efficiency Q-switched erbium fiber laser using a Bragg grating-based modulator
Abstract In this work we analyze the behavior of an erbium-doped fiber laser which is based on a simple scheme. Excitation of the active medium is performed in the 980 nm pump band with a CW semiconductor laser source. Two fiber Bragg gratings acting as mirrors of the Fabry–Perot laser cavity were used. One of these gratings was mounted over a piezoelectric (PZT) element. By applying voltage pulses to the piezoelectric, the laser cavity was temporally modulated and Q-switched laser pulses up to 530 mW peak powers at 3 kHz were obtained. Typical laser emission of 2–3 μs temporal widths and 0.1 nm of optical bandwidth have been achieved when the system was operated at 18.5 kHz repetition rate…
High-repetition rate acoustic-induced Q-switched all-fiber laser
We report a high repetition rate actively Q switched all fiber laser. The acousto optic interaction controls the cou pling between co propagating core and cladding modes and is used to modulate the optical losses of the cavity, which permits to perform active Q-switching. Using 1.4 m of 300 ppm Er-doped fiber and a maximum pump power of 120 mW, we have obtained up to 1 W peak power pulses, with a pulse repetition rate that can be continuously varied from 1 Hz to 120 kHz and a pulse width that changes from 70 ns to 2.2 μs.
Q-switched all-fiber laser based on magnetostriction modulation of a Bragg grating
We report an actively Q-switched all-fiber laser based on magnetostriction modulation of a Bragg grating. The laser employs a pair of Bragg gratings as reflective mirrors, one of which is bonded to a magnetostrictive element. Lengthening of the magnetostrictive element when a magnetic field is applied shifts the Bragg wavelength of the grating, allowing control of the Q-factor of the cavity and, thus, performing active Q-switching. The magnetostrictive modulator is small, compact and requires less than 300 mW electrical drive power. Using erbium-doped fiber and a maximum pump power of 120 mW, Q-switch pulses of more than 1 W peak power were obtained, with a pulse repetition rate that can be…
Spectral properties of a variable period Bragg grating including a segment isolated of external deformations
In this work the behavior of a Bragg grating of variable period (usually called a linearly chirped fiber Bragg grating — CFBG) is analyzed when a small portion of it is fixed so that its properties remain unchanged, while the rest of the grating is affected by a longitudinal deformation. The system was simulated using the Transfer Matrix Method to obtain its behavior under different levels of deformation and it was observed the appearance of negative peaks in the spectral response (transmission peaks). The analysis allowed characterizing the system with different sizes of the fixed portion (defects) (0.5 to 6 mm), for a grating with 10 cm long and 3 nm spectral width.