0000000000026270
AUTHOR
V. L. Kulakov
Finite element modelling of slipage between FRP rebar and concrete in pull-out test
The paper presents numerical results of direct pull-out test of glass fiber-reinforced polymer (GFRP) rebars embedded in concrete. Rebars of three different cross-sections are considered: circular without longitudinal ribs and with two and four ribs. The design analyses of the rebar configurations embedded in concrete are investigated by the 3D finite element method (FEM), which takes into account the non-linearity using ANSYS software. The results of the numerical model with two ribs were compared with the experimental results. Then, the effect of different rebar geometries to the load-slip pull-out curves was studied. It is concluded that the influence of rib height and width on the pull-…
Delamination Detection in Carbon Fibre Reinforced Composites Using Electrical Resistance Measurement
In the present study 2-D numerical analysis of strip-type laminated composite specimens with and without damage is considered and numerical investigation is carried out by using a finite element method. The surface and oblique resistances are numerically calculated according to the two-probe and four-probe methods. The electrical conductivity of the composite laminate in the longitudinal direction is constant, while the electrical conductivity in the through-thickness direction is used as a variable in the parametric study. The resistance change due to delamination for each case is estimated by comparing the obtained resistance with the corresponding resistance of the specimen without delam…
Development of Composites with a Self-Healing Function
This research aimed to realize experimentally the facilevascular self-healing system in epoxy glass fibre reinforced composite. Using flexiblepolytetrafluoroethylene tubes as removable preforms, the channels were embeddedinto both neat epoxy resin and unidirectional glass-fibre reinforced epoxy laminate.Room temperature curable epoxy resin with a surfactant and an amine-basedhardener were the components of the binary healing agent. The specimens oftapered double cantilever beam geometry were subjected to Mode I fracture tests.Fracture of specimens released the healing agent from channels and triggeredself-healing process of the crack. Tested neat epoxy resin specimensdemonstrated recovery o…
Effective electrical conductivity of carbon nanotube–epoxy nanocomposites
The electrical conductivity of carbon nanotube–epoxy composites is investigated analytically and experimentally. The theoretical predictions of the effective electrical conductivity of carbon nanotube–epoxy composites were performed by the analytical approach based on a micromechanical model of composites. The parametric analysis carried out revealed an influence of geometrical and electrical parameters of the micromechanical model on the effective electrical conductivity of carbon nanotube–epoxy nanocomposite. The nanocomposites made from the DGEBA-based and RTM6 epoxy resins filled with different weight content of Baytubes C150P and N7000 multi-walled carbon nanotubes were prepared. The …
Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension
The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.
Experimental Investigation on Stiffness and Strength of Single-Lap Z-Pinned Joints in a Laminated CFRP Stress-Ribbon Strip
Carbon fiber-reinforced polymer (carbon-polymer) is an advanced lightweight composite material with high strength and excellent resistance to corrosion and fatigue. Over the past decades, application of fiber-reinforced polymers has been spread from the aerospace to other branches of industry such as automobile and civil engineering. Unidirectional carbon-polymers have a high potential for replacing steel in tensile members. Recently, the first carbonpolymer stress-ribbon bridge has been constructed in Germany. The non-laminated strip-loop carbon-polymer thin strips were used as the load bearing components in this bridge. In comparison with the laminated components, the applied cables are c…