0000000000181482
AUTHOR
J.a. Valls
showing 18 related works from this author
ATLAS TileCal Read Out Driver production
2007
The production tests of the 38 ATLAS TileCal Read Out Drivers (RODs) are presented in this paper. The hardware specifications and firmware functionality of the RODs modules, the test-bench and the test procedure to qualify the boards are described. Finally the performance results, the temperature studies and high rate tests are shown and discussed.
The optical instrumentation of the ATLAS Tile Calorimeter
2013
The purpose of this Note is to describe the optical assembly procedure called here Optical Instrumentation and the quality tests conducted on the assembled units. Altogether, 65 Barrel (or LB) modules were constructed - including one spare - together with 129 Extended Barrel (EB) modules (including one spare). The LB modules were mechanically assembled at JINR (Dubna, Russia) and transported to CERN, where the optical instrumentation was performed with personnel contributed by several Institutes. The modules composing one of the two Extended Barrels (known as EBA) were mechanically assembled in the USA, and instrumented in two US locations (ANL, U. of Michigan), while the modules of the oth…
Testbeam studies of production modules of the ATLAS Tile Calorimeter
2009
We report test beam studies of {11\,\%} of the production ATLAS Tile Calorimeter modules. The modules were equipped with production front-end electronics and all the calibration systems planned for the final detector. The studies used muon, electron and hadron beams ranging in energy from 3~GeV to 350~GeV. Two independent studies showed that the light yield of the calorimeter was $\sim 70$~pe/GeV, exceeding the design goal by {40\,\%}. Electron beams provided a calibration of the modules at the electromagnetic energy scale. Over 200~calorimeter cells the variation of the response was {2.4\,\%}. The linearity with energy was also measured. Muon beams provided an intercalibration of the respo…
Search for the t and b' quarks in hadronic decays of the Z0 boson
1990
We present a search for the third generation up type quark t and a possible fourth down type quark b' in hadronic Z0 decays observed in DELPHI at the LEP collider. For any scenario with a decay through the charged current or into a charged Higgs with a mass at least 6 GeV/c2 below the t and 3 GeVc2 below the b' mass, we set a lower limit for the t quark mass at 44.0 GeV/c2 and for the b' mass at 44.5 GeV/c2. For specific scenarios the mass limits are slightly higher, e.g. for charged current decays the limits are 44.5 and 45.0 GeV/c2 respectively, where all limits are given at a 95% confidence level. © 1990.
Search for heavy charged scalars in Z$^0$ Decays
1990
Using a sample of Z0's corresponding to about 12 000 events, we have searched for the production of charged scalars, primarily charged Higgs particles, decaying into c̄scs̄, τν+jets, and τντν. The average detection efficiency is 20%. No candidate was found in the leptonic modes. Masses in the range up to 30-36 GeV/c2 are excluded, extending the mass domain covered by previous e+e- machines.
Development of an optical link card for the upgrade phase II of TileCal experiment
2010
This work presents the design of an optical link card developed in the frame of the R&D activities for the phase 2 upgrade of the TileCal experiment as part of the evaluation of different technologies for the final choice in the next two years. The board is designed as a mezzanine which can work independently or plugged in the Optical Multiplexer Board of the TileCal backend electronics. It includes two SNAP 12 optical connectors able to transmit and receive up to 75 Gbps and one SFP optical connector for lower speeds and compatibility with existing hardware as the Read Out Driver. All processing is done in a Stratix II GX FPGA. Details are given on the hardware design including signal and …
Combined performance studies for electrons at the 2004 ATLAS combined test-beam
2010
In 2004 at the ATLAS (A Toroidal LHC ApparatuS) combined test beam, one slice of the ATLAS barrel detector (including an Inner Detector set-up and the Liquid Argon calorimeter) was exposed to particles from the H8 SPS beam line at CERN. It was the first occasion to test the combined electron performance of ATLAS. This paper presents results obtained for the momentum measurement p with the Inner Detector and for the performance of the electron measurement with the LAr calorimeter (energy E linearity and resolution) in the presence of a magnetic field in the Inner Detector for momenta ranging from 20 GeV/c to 100 GeV/c. Furthermore the particle identification capabilities of the Transition Ra…
Search For Light Neutral Higgs Particles Produced In Z0-decays
1990
A search for the neutral Higgs boson in Z0-decays has been performed using the DELPHI detector at the Large Electron Positron collider (LEP) at CERN. We looked for the decay of Z0 into a neutral Higgs particle and a pair of fermions. No events fulfilled the criteria for H0-production. Our results, which are based on an integrated luminosity of 530 nb-1, exclude a minimal Standard Model Higgs boson with a mass in the range 210 MeV/c2 to 14 GeV/c2 at 95% confidence level.
Search for pair production of neutral Higgs bosons in Z$^0$ decays
1990
The pair production of the lightest scalar Higgs boson, h, and a pseudoscalar Higgs boson, A, was searched for in a data sample containing 10 000 hadronic Z0 decays. The search involved both leptonic and purely hadronic decay channels of each Higgs boson. No signal was found, and limits on the Higgs boson masses, in the framework of the minimal supersymmetric extension of the standard model, ar reported up to 35 GeV/c2 at 95% CL, for both tan β > 1 and tan β < 1, where tan β is the ratio of the vacuum expectation values of the two Higgs doublets.
A precise measurement of the Z resonance parameters through its hadronic decays
1990
A measurement of the cross section for e+e-→ hadrons using 11 000 hadronic decays of the Z boson at ten different center-of-mass energies is presented. A three-parameter fit gives the following values for the Z mass MZ, the total width ΓZ, the product of the electronic and hadronic partial widths ΓeΓh, and the unfolded pole cross section σ0: MZ = 91.171 ± 0.030 (stat.) ± 0.030 (beam) GeV, ΓZ = 2.511 ± 0.065 GeV, ΓeΓh = 0.148 ± 0.006 (stat.) ± 0.004 (syst.) GeV2, σ0 = 41.6 ± 0.7 (stat.) ± 1.1 (syst.) nb, Good agreement with the predictions of the standard model is observed. From a two-parameter fit the number of massless neutrino generations is found to be Nv = 2.91 ± 0.26. Thus the hypothes…
Study of energy response and resolution of the ATLAS barrel calorimeter to hadrons of energies from 20 to 350 GeV
2010
A fully instrumented slice of the ATLAS detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the results of the measurements of the response of the barrel calorimeter to hadrons with energies in the range 20 to 350 GeV and beam impact points and angles corresponding to pseudorapidity values in the range 0.2-0.65 are reported. The results are compared to the predictions of a simulation program using the Geant 4 toolkit.
The Optical Multiplexer Board for the ATLAS Hadronic Tile Calorimeter
2007
This paper presents the architecture and the status of the optical multiplexer board (OMB) for the ATLAS/LHC tile hadronic calorimeter (TileCal). This board will analyze the front-end data CRC to prevent bit and burst errors produced by radiation. Besides, due to its position within the data acquisition chain it will be used to emulate front-end data for tests. The first two prototypes of the final OMB 9U version have been produced at CERN. Detailed design issues and manufacturing features of these prototypes are described. These prototypes are being validated while firmware developments are being implemented in the programmable devices of the board.
Development of the Optical Multiplexer Board Prototype for Data Acquisition in the TileCal System
2006
This paper describes the development of the optical multiplexer board (OMB), also known as PreROD board, for the TileCal readout system in the ATLAS experiment. The aim of this board is to overcome the problems that may arise in the integrity of data due to radiation effects. The solution adopted has been to add redundancy to data transmission and so two optical fibers with the same data come out from the detector front end boards. The OMB has to decide in real time which fiber, eventually, carries data with no errors switching it to the output link connected to the read out driver (ROD) motherboard where data processing takes place. Besides, the board may be also used as a data injector fo…
Photon reconstruction in the ATLAS Inner Detector and Liquid Argon Barrel Calorimeter at the 2004 Combined Test Beam
2011
The reconstruction of photons in the ATLAS detector is studied with data taken during the 2004 Combined Test Beam, where a full slice of the ATLAS detector was exposed to beams of particles of known energy at the CERN SPS. The results presented show significant differences in the longitudinal development of the electromagnetic shower between converted and unconverted photons as well as in the total measured energy. The potential to use the reconstructed converted photons as a means to precisely map the material of the tracker in front of the electromagnetic calorimeter is also considered. All results obtained are compared with a detailed Monte-Carlo simulation of the test-beam setup which i…
Study of the response of the ATLAS central calorimeter to pions of energies from 3 to 9 GeV
2009
Çetin, Serkant Ali (Dogus Author) A fully instrumented slice of the ATLAS central detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the response of the central calorimeters to pions with energies in the range between 3 and 9 GeV is presented. The linearity and the resolution of the combined calorimetry (electromagnetic and hadronic calorimeters) was measured and compared to the prediction of a detector simulation program using the toolkit Geant 4.
Measurement of pion and proton response and longitudinal shower profiles up to 20 nuclear interaction lengths with the ATLAS Tile calorimeter
2010
The response of pions and protons in the energy range of 20–180 GeV, produced at CERN's SPS H8 test-beam line in the ATLAS iron–scintillator Tile hadron calorimeter, has been measured. The test-beam configuration allowed the measurement of the longitudinal shower development for pions and protons up to 20 nuclear interaction lengths. It was found that pions penetrate deeper in the calorimeter than protons. However, protons induce showers that are wider laterally to the direction of the impinging particle. Including the measured total energy response, the pion-to-proton energy ratio and the resolution, all observations are consistent with a higher electromagnetic energy fraction in pion-indu…
Mechanical construction and installation of the ATLAS tile calorimeter
2013
This paper summarises the mechanical construction andinstallation of the Tile Calorimeter for the ATLASexperiment at the Large Hadron Collider in CERN, Switzerland. The TileCalorimeter is a sampling calorimeter using scintillator as the sensitivedetector and steel as the absorber and covers the central region of the ATLASexperiment up to pseudorapidities ±1.7. The mechanical construction ofthe Tile Calorimeter occurred over a periodof about 10 years beginning in 1995 with the completionof the Technical Design Report and ending in 2006 with the installationof the final module in the ATLAS cavern. Duringthis period approximately 2600 metric tons of steel were transformedinto a laminated struc…
The ATLAS tile calorimeter ROD injector and multiplexer board
2011
Abstract The ATLAS Tile Calorimeter is a sampling detector composed by cells made of iron-scintillator tiles. The calorimeter cell signals are digitized in the front-end electronics and transmitted to the Read-Out Drivers (RODs) at the first level trigger rate. The ROD receives triggered data from up to 9856 channels and provides the energy, phase and quality factor of the signals to the second level trigger. The back-end electronics is divided into four partitions containing eight RODs each. Therefore, a total of 32 RODs are used to process and transmit the data of the TileCal detector. In order to emulate the detector signals in the production and commissioning of ROD modules a board call…