0000000000201267
AUTHOR
Victor W. Bergmann
Removal of Surface Oxygen Vacancies Increases Conductance Through TiO(2) Thin Films for Perovskite Solar Cells
[Image: see text] We report that UV–ozone treatment of TiO(2) anatase thin films is an efficient method to increase the conductance through the film by more than 2 orders of magnitude. The increase in conductance is quantified via conductive scanning force microscopy on freshly annealed and UV–ozone-treated TiO(2) anatase thin films on fluorine-doped tin oxide substrates. The increased conductance of TiO(2) anatase thin films results in a 2% increase of the average power conversion efficiency (PCE) of methylammonium lead iodide-based perovskite solar cells. PCE values up to 19.5% for mesoporous solar cells are realized. The additional UV–ozone treatment results in a reduced number of oxygen…
The Interplay of Contact Layers: How the Electron Transport Layer Influences Interfacial Recombination and Hole Extraction in Perovskite Solar Cells.
Charge-selective contact layers in perovskite solar cells influence the current density–voltage hysteresis, an effect related to ion migration in the perovskite. As such, fullerene-based electron transport layers (ETLs) suppress hysteresis by reducing the mobile ion concentration. However, the impact of different ETLs on the electronic properties of other constituent device layers remains unclear. In this Kelvin probe force microscopy study, we compared potential distributions of methylammonium lead iodide-based solar cells with two ETLs (planar TiO2 and C60-functionalized self-assembled monolayer) with different hysteretic behavior. We found significant changes in the potential distributio…
Know your full potential: Quantitative Kelvin probe force microscopy on nanoscale electrical devices
In this study we investigate the influence of the operation method in Kelvin probe force microscopy (KPFM) on the measured potential distribution. KPFM is widely used to map the nanoscale potential distribution in operating devices, e.g., in thin film transistors or on cross sections of functional solar cells. Quantitative surface potential measurements are crucial for understanding the operation principles of functional nanostructures in these electronic devices. Nevertheless, KPFM is prone to certain imaging artifacts, such as crosstalk from topography or stray electric fields. Here, we compare different amplitude modulation (AM) and frequency modulation (FM) KPFM methods on a reference s…
How the formation of interfacial charge causes hysteresis in perovskite solar cells
In this study, we discuss the underlying mechanism of the current-voltage hysteresis in a hybrid lead-halide perovskite solar cell. We have developed a method based on Kelvin probe force microscopy that enables mapping charge redistribution in an operating device upon a voltage- or light pulse with sub-millisecond resolution. We observed the formation of a localized interfacial charge at the anode interface, which screened most of the electric field in the cell. The formation of this charge happened within 10 ms after applying a forward voltage to the device. After switching off the forward voltage, however, these interfacial charges were stable for over 500 ms and created a reverse electri…
Humidity-Induced Grain Boundaries in MAPbI3 Perovskite Films
Methylammonium lead halide perovskites (MAPbI3) are very sensitive to humid environments. We performed in situ scanning force microscopy and in situ X-ray diffraction measurements on MAPbI3 films to track changes in the film morphology and crystal structure upon repeated exposure to a high relative humidity environment (80%). We found that the appearance of monohydrate (MAPbI3·H2O) Bragg reflections coincided with the appearance of additional grain boundaries. Prolonging the exposure time to humidity induced more grain boundaries and steps in the MAPbI3 films, and the peak intensities of the monohydrate MAPbI3·H2O increased. The monohydrate was not stable under dry atmosphere and could be r…
Local Time-Dependent Charging in a Perovskite Solar Cell
Efficient charge extraction within solar cells explicitly depends on the optimization of the internal interfaces. Potential barriers, unbalanced charge extraction, and interfacial trap states can prevent cells from reaching high power conversion efficiencies. In the case of perovskite solar cells, slow processes happening on time scales of seconds cause hysteresis in the current-voltage characteristics. In this work, we localized and investigated these slow processes using frequency-modulation Kelvin probe force microscopy (FM-KPFM) on cross sections of planar methylammonium lead iodide (MAPI) perovskite solar cells. FM-KPFM can map the charge density distribution and its dynamics at intern…
Ferroelastic Fingerprints in Methylammonium Lead Iodide Perovskite
Methylammonium lead iodide (MAPbI3) perovskite shows an outstanding performance in photovoltaic devices. However, certain material properties, especially the possible ferroic behavior, remain unclear. We observed distinct nanoscale periodic domains in the piezoresponse of MAPbI3(Cl) grains. The structure and the orientation of these striped domains indicate ferroelasticity as their origin. By correlating vertical and lateral piezoresponse force microscopy experiments performed at different sample orientations with X-ray diffraction, the preferred domain orientation is suggested to be the a1–a2-phase. The observation of these ferroelastic fingerprints appears to strongly depend on the film t…