0000000000211266

AUTHOR

R. Degele

Relative luminosity measurement of the LHC with the ATLAS forward calorimeter

In this paper it is shown that a measurement of the relative luminosity changes at the LHC may be obtained by analysing the currents drawn from the high voltage power supplies of the electromagnetic section of the forward calorimeter of the ATLAS detector. The method was verified with a reproduction of a small section of the ATLAS forward calorimeter using proton beams of known beam energies and variable intensities at the U-70 accelerator at IHEP in Protvino, Russia. The experimental setup and the data taking during a test beam run in April 2008 are described in detail. A comparison of the measured high voltage currents with reference measurements from beam intensity monitors shows a linea…

research product

Measurement of the response of Silicon Photomultipliers from single photon detection to saturation

Abstract The development of Silicon Photomultipliers (SiPM) is very dynamic and a large variety of types exists. Important SiPM characteristics include the size and number of pixels, the gain, the photon detection efficiency (PDE), the recovery time, and correlated noise. SiPMs are particularly suitable for single-photon detection and low-intensity exposures. For photon numbers (PDE corrected) reaching the number of pixels, however, the sensors saturate. In this work, we present comprehensive response measurements for state-of-the-art SiPMs using an experimental setup based on a tunable picosecond laser. Several models are applied to the measured response curves, taking particularly correla…

research product

Topological and Central Trigger Processor for 2014 LHC luminosities

The ATLAS experiment is located at the European Center for Nuclear Research (CERN) in Switzerland. It is designed to observe phenomena that involve highly massive particles produced in the collisions at the Large Hadron Collider (LHC): the world’s largest and highest-energy particle accelerator. Event triggering and Data Acquisition is one of the extraordinary challenges faced by the detectors at the high luminosity LHC collider. During 2011, the LHC reached instantaneous luminosities of 4 10^33 cm−1 s−1 and produced events with up to 24 interactions per colliding proton bunch. This places stringent operational and physical requirements on the ATLAS Trigger in order to reduce the 40MHz coll…

research product

An FPGA based demonstrator for a topological processor in the future ATLAS L1-Calo trigger “GOLD”

Abstract: The existing ATLAS trigger consists of three levels. The level 1 (L1) is an FPGAs based custom designed trigger, while the second and third levels are software based. The LHC machine plans to bring the beam energy to the maximum value of 7 TeV and to increase the luminosity in the coming years. The current L1 trigger system is therefore seriously challenged. To cope with the resulting higher event rate, as part of the ATLAS trigger upgrade, a new electronics module is foreseen to be added in the ATLAS Level-1 Calorimeter Trigger electronics chain: the Topological Processor (TP). Such a processor needs fast optical I/O and large aggregate bandwidth to use the information on trigger…

research product

Development of Structured Scintillator Tiles for High-Granularity Calorimeters

Calorimeters with a fine 3-D segmentation are considered to be a very promising technology for future high-energy physics experiments, since they provide in combination with particle flow algorithms excellent jet energy resolution and particle identification capabilities. Depending on the size, millions of individual channels consisting of a photosensor coupled to a scintillator tile have to be assembled. The usage of structured plastic scintillators with optically separated segments simplifies the mass production. We present the design, production, and performance of a 36 cm × 36 cm scintillator tile divided into 144 segments matching the geometry of the SiPM-based calorimeter frontend dev…

research product

Latest Frontier Technology and Design of the ATLAS Calorimeter Trigger Board Dedicated to Jet Identification for the LHC Run 3

To cope with the enhanced luminosity of the beam delivered by the Large Hadron Collider (LHC) in 2020, the “A Toroidal LHC ApparatuS” (ATLAS) experiment has planned a major upgrade. As part of this, the trigger at Level1 based on calorimeter data will be upgraded to exploit fine-granularity readout using a new system of Feature Extractors, which each use different physics objects for the trigger selection. The article focusses on the jet Feature EXtractor (jFEX) prototype, one of the three types of Feature Extractors. Up to 2 TB/s have to be processed to provide jet identification (including large area jets) and measurements of global variables within few hundred nanoseconds latency budget.…

research product

An FPGA based Topological Processor Prototype for the ATLAS Level-1 Trigger Upgrade

By 2014 the LHC will collide proton bunches at 14TeV with an increased instantaneous luminosity up to 3·10³⁴cm⁻²s⁻¹. The resulting higher event rate will challenge the existing ATLAS trigger system. A reduction on the trigger rate can be achieved by selecting interesting channels based on their expected decay topology and thus reducing background. This will be achieved by introducing of a new FPGA based module in the Level-1 trigger: the Topological Processor L1Topo. With L1Topo it will be possible for the first time to concentrate detailed information from the entire calorimeters and the muon detector into a single module. L1Topo will receive a total aggregate bandwidth of 1Tb/s. The data …

research product

Comparison of Silicon Photomultiplier Characteristics using Automated Test Setups

Silicon Photomultipliers (SiPM) are photo-sensors consisting of an array of hundreds to thousands pixels with a typical pitch of 10-100 μm. They exhibit an excellent photon counting and time resolution. Therefore applications of SiPMs are emerging in many fields. In order to characterize SiPMs, the PRISMA Detector Lab at Mainz has established three automated test setups. Setup-A is dedicated to measure the gain, the dark count rate and the optical crosstalk probability. The temperature dependencies are characterized by operating the setup in a climate chamber. Setup-B is an optical system to measure the photon detection efficiency. Setup-C addresses the most challenging aspect of comparing …

research product

Upgrade of the ATLAS Central Trigger for LHC Run-2

The increased energy and luminosity of the LHC in the run-2 data taking period requires a more selective trigger menu in order to satisfy the physics goals of ATLAS. Therefore the electronics of the central trigger system is upgraded to allow for a larger variety and more sophisticated trigger criteria. In addition, the software controlling the central trigger processor (CTP) has been redesigned to allow the CTP to accommodate three freely configurable and separately operating sets of sub detectors, each independently using the almost full functionality of the trigger hardware. This new approach and its operational advantages are discussed as well as the hardware upgrades.

research product

Upgrade of the ATLAS Level-1 trigger with an FPGA based Topological Processor

The ATLAS experiment is located at the European Centre for Nuclear Research (CERN) in Switzerland. It is designed to measure decay properties of high energetic particles produced in the protons collisions at the Large Hadron Collider (LHC). The LHC has a proton collision at a frequency of 40 MHz, and thus requires a trigger system to efficiently select events down to a manageable event storage rate of about 400Hz. Event triggering is therefore one of the extraordinary challenges faced by the ATLAS detector. The Level-1 Trigger is the first rate-reducing step in the ATLAS Trigger, with an output rate of 75kHz and decision latency of less than 2.5$\mu$s. It is primarily composed of the Calori…

research product

Design and testing of the high speed signal densely populated ATLAS calorimeter trigger board dedicate to jet identification

Abstract—The ATLAS experiment has planned a major upgrade in view of the enhanced luminosity of the beam delivered by the Large Hadron Collider (LHC) in 2021. As part of this, the trigger at Level-1 based on calorimeter data will be upgraded to exploit fine-granularity readout using a new system of Feature Extractors (three in total), which each uses different physics objects for the trigger selection. The contribution focusses on the jet Feature EXtractor (jFEX) prototype. Up to a data volume of 2 TB/s has to be processed to provide jet identification (including large area jets) and measurements of global variables within few hundred nanoseconds latency budget. Such requirements translate …

research product

The Topological Processor for the future ATLAS Level-1 Trigger: From design to commissioning

The ATLAS detector at the Large Hadron Collider (LHC) is designed to measure decay properties of high energetic particles produced in the proton-proton collisions. During its first run, the LHC collided proton bunches at a frequency of 20 MHz, and therefore the detector required a Trigger system to efficiently select events down to a manageable event storage rate of about 400 Hz. By 2015 the LHC instantaneous luminosity will be increased up to 3×1034cm−2s−1: this represents an unprecedented challenge faced by the ATLAS Trigger system. To cope with the higher event rate and efficiently select relevant events from a physics point of view, a new element will be included in the Level-1 Trigger …

research product

Liquid argon calorimeter performance at high rates

Abstract We project the performance of the ATLAS liquid argon endcap and forward calorimeters at the planned high luminosity LHC option HL-LHC by exposing small calorimeter modules of the electromagnetic, hadronic, and forward calorimeters to high intensity beams at IHEP/Protvino. The beam intensity extends well beyond the maximum expected for these calorimeters at HL-LHC. The signal reconstruction and calorimeter performance have been studied in full detail.

research product