0000000000291572
AUTHOR
Gints Kucinskis
Electrochemical performance of Na2FeP2O7/C cathode for sodium-ion batteries in electrolyte with fluoroethylene carbonate additive
Abstract Solution synthesis was used to prepare pristine Na2FeP2O7 and Na2FeP2O7/C composite cathode materials for sodium-ion batteries, using glucose as a carbon source. While the pristine Na2FeP2O7 displays capacity of only 45 mAh/g due to the relatively large grain size, the addition of carbon increases the capacity to up to 92 mAh/g (95% of the theoretical 97 mAh/g capacity) with excellent rate capability, as 44 mAh/g capacity is still retained even at 20 C (1.94 A/g) current. The optimal content of carbon was found to be 4.8%. The initial capacity of 81 mAh/g is fully retained after 500 cycles at 1 C, indicating excellent cycle life. Measurements were carried out in 1 M NaClO4 salt in …
Graphene in lithium ion battery cathode materials: A review
Abstract Graphene is a relatively new and promising material, displaying a unique array of physical and chemical properties. Although considered to be especially promising for the use in energy storage applications, graphene has only recently been implemented as an electron conducting additive for lithium ion battery cathode materials. In current studies graphene is found to significantly improve cathode electrochemical performance. As the charge capacity, rate capability and cyclability of lithium ion batteries are still in ever-remaining need of improvement, this article examines the prospects of graphene implementation into lithium ion battery cathodes to meet such demands. The existing …
Enhanced Electrochemical Properties of Na0.67MnO2 Cathode for Na-Ion Batteries Prepared with Novel Tetrabutylammonium Alginate Binder
This research was funded by the State Education Development Agency, the Republic of Latvia, grant number 1.1.1.2/VIAA/1/16/166, "Advanced Materials for Sodium-Ion Batteries". Institute of Solid-State Physics, University of Latvia as the Centre of Excellence has received funding from the European Union's Horizon 2020 Framework Program H2020-WIDESPREAD-01-2016-2017-TeamingPhase2 under grant agreement No. 739508, project CAMART2.
Experimental Confirmation of C-Rate Dependent Minima Shifts in Arrhenius Plots of Li-Ion Battery Aging
The part of the research performed at ZSW was carried out in the framework of the industrial collective research program (IGF no. 20884 N/2). It was supported by the Federal Ministry for Economic Affairs and Climate Action (BMWK) through the AiF (German Federation of Industrial Research Associations eV) based on a decision taken by the German Bundestag. G.K. acknowledges funding from the Latvian Council of Science (lzp-2020/1-0425) and from the European Union’s Horizon 2020 Framework Program under grant agreement No. 739508, project CAMART2.
Physical and electrochemical properties of LiFePO4/C thin films deposited by direct current and radiofrequency magnetron sputtering
Abstract In this study, LiFePO 4 /C thin films with various contents of carbon were prepared by direct current (DC), radiofrequency (RF) and combined (DC/RF) magnetron sputtering methods. Influences of the composition, morphology and microstructure on the electrochemical properties of LiFePO 4 /C thin films are investigated by studying charge–discharge curves, cyclic voltammetry and electrochemical impedance spectroscopy. Cyclic voltammogram of the LiFePO 4 /C thin film showed the typical redox reaction peaks characterizing the electrochemical lithium insertion/extraction reactions in LiFePO 4 . Obtained LiFePO 4 /C thin films have relatively high charge capacities (127 mAh g − 1 ). It was …
Characterization of LiFePO4/C Composite Thin Films Using Electrochemical Impedance Spectroscopy
The composite LiFePO4/C thin films were prepared on steel substrate by radio frequency (RF) magnetron sputtering. Electrochemical properties of the obtained thin films were investigated by cyclic voltammetry charge-discharge measurements and electrochemical impedance spectroscopy (EIS). The films annealed at 550 °C exhibited a couple of redox peaks at 3.45 V vs. Li/Li + characteristic for the electrochemical lithium insertion/extraction in LiFePO4. At low current rate such composite thin film showed a discharge capacity of over 110 mAh g -1 . The dependence of charge transfer resistance, double layer capacitance and lithium diffusion coefficients on applied electrode potential were calculat…
Electrophoretic Nanocrystalline Graphene Film Electrode for Lithium Ion Battery
Graphene sheets were fabricated by electrophoretic deposition method from water suspension of graphene oxide followed by thermal reduction. The formation of nanocrystalline graphene sheets has been confirmed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. The electrochemical performance of graphene sheets as anode material for lithium ion batteries was evaluated by cycling voltammetry, galvanostatic charge-discharge cycling, and electrochemical impedance spectroscopy. Fabricated graphene sheets exhibited high discharge capacity of about 1120 mAhg−1 and demonstrated good reversibility of lithium intercalation and deintercalation in graphene sheet film with capacity…
Electrophoretically deposited α-Fe2O3 and TiO2 composite anchored on rGO with excellent cycle performance as anode for lithium ion batteries
Abstract Two nanostructured oxides, α-Fe2O3 and TiO2 with a particle diameters 50 nm and 21 nm, were mixed with graphene oxide (GO). Composite thin films on a stainless steel substrate were obtained by electrophoretic deposition (EPD) procedure from water suspensions: α-Fe2O3/GO, TiO2/GO and α-Fe2O3/TiO2/GO. Subsequently reduction of as-prepared thin films was performed. Thicknesses of acquired films were evaluated in the range of 2–6 μm. Structure and morphology were investigated as well as electrochemical properties of all samples were studied. The results revealed that α-Fe2O3/TiO2/rGO (in this article denoted as FTGO) exhibited the specific discharge capacity of 790 mAh·g−1 after 150 cy…