showing 14 related works from this author
Use of Biochar as Filler for Biocomposite Blown Films: Structure-Processing-Properties Relationships
2021
In this work, biocomposite blown films based on poly(butylene adipate-co-terephthalate) (PBAT) as biopolymeric matrix and biochar (BC) as filler were successfully fabricated. The materials were subjected to a film-blowing process after being compounded in a twin-screw extruder. The preliminary investigations conducted on melt-mixed PBAT/BC composites allowed PBAT/BC 5% and PBAT/BC 10% to be identified as the most appropriate formulations to be processed via film blowing. The blown films exhibited mechanical performances adequate for possible application as film for packaging, agricultural, and compost bags. The addition of BC led to an improvement of the elastic modulus, still maintaining h…
Morphology, Rheological and Mechanical Properties of Isotropic and Anisotropic PP/rPET/GnP Nanocomposite Samples
2021
The effect of graphene nanoplatelets (GnPs) on the morphology, rheological, and mechanical properties of isotropic and anisotropic polypropylene (PP)/recycled polyethylene terephthalate (rPET)-based nanocomposite are reported. All the samples were prepared by melt mixing. PP/rPET and PP/rPET/GnP isotropic sheets were prepared by compression molding, whereas the anisotropic fibers were spun using a drawing module of a capillary viscometer. The results obtained showed that the viscosity of the blend is reduced by the presence of GnP due to the lubricating effect of the graphene platelets. However, the Cox–Merz rule is not respected. Compared to the PP/rPET blend, the GnP led to a slight incre…
The Effect of Calcium Carbonate on the Photo-Oxidative Behavior of Poly(butylene adipate-co-terephthalate)
2020
The aim of this work is to evaluate the influence of nanosized CaCO3 on the photo-oxidation of poly(butylene adipate-co-terephthalate) (PBAT)-based nanocomposites. The PBAT/CaCO3 nanocomposites are prepared by using a corotating twin-screw extruder with 0, 2, and 5 wt% of CaCO3. The films are obtained by film blowing process. Specimens of the nanocomposites and that of the pure polymer are subjected to accelerated aging with a cycle of 8 h of light at a temperature of 55 °C followed by 4 h condensation at 45 °C to evaluate the effects of the CaCO3 addition on the photo-oxidation of PBAT. The results indicate that the modulus and tensile strength of the nanocomposites are increased significa…
Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester
2021
This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that th…
PBAT Based Composites Reinforced with Microcrystalline Cellulose Obtained from Softwood Almond Shells
2021
This study explores the processability, mechanical, and thermal properties of biocompostable composites based on poly (butylene adipate-co-terephthalate) (PBAT) as polymer matrix and microcrystalline cellulose (MCC) derived from softwood almond (Prunus dulcis) shells (as-MCC) as filler at two different weight concentration, i.e., 10 wt% and 20 wt%. The materials were processed by melt mixing and a commercial MCC (c-MCC) was used as filler comparison. The fibrillar shape of as-MCC particles was found to change the rheological behavior of PBAT, particularly at the highest concentration. The melt mixing processing allowed obtaining a uniform dispersion of both kinds of fillers, slightly reduci…
An Additive Model to Predict the Rheological and Mechanical Properties of Polypropylene Blends Made by Virgin and Reprocessed Components
2021
In this work, an additive model for the prediction of the rheological and mechanical properties of monopolymer blends made by virgin and reprocessed components is proposed. A polypropylene sample has been reprocessed more times in an extruder and monopolymer blends have been prepared by simulating an industrial process. The scraps are exposed to regrinding and are melt reprocessed before mixing with the virgin polymer. The reprocessed polymer is, then, subjected to some thermomechanical degradation. Rheological and mechanical experimental data have been compared with the theoretical predictions. The results obtained showed that the values of this simple additive model are a very good fit fo…
Effect of ultraviolet and moisture action on biodegradable polymers and their blend
2020
In this work, the suitability of polylactic acid (PLA), polybutylene adipate terephthalate (PBAT) and PBAT/PLA blend samples to outdoor applications were investigated in terms of mechanical, morphological and visual properties in presence of ultraviolet action and water, finding that PLA in particular can be actually considered for such applications.
The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.
2022
Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could …
Investigation on the Properties and on the Photo-Oxidation Behaviour of Polypropylene/Fumed Silica Nanocomposites
2021
This work investigates the effects of very small amounts of fumed silica on the morphology and on the rheological and mechanical behaviour of polypropylene nanocomposites and on their photo-oxidation behaviour. Polypropylene nanocomposites were prepared using a twin-screw corotating extruder with 0, 1 and 2 wt/wt% of SiO2. Morphological, mechanical, thermomechanical and rheological properties were examined. It was found that the viscosity of the matrix is reduced by the presence of the silica nanoparticles, suggesting a poor adhesion between the two phases and probably some lubricating effect. On the contrary, the mechanical and, in particular, the thermomechanical properties of the matrix …
Recycling of a Biodegradable Polymer Blend
2020
Mechanical recycling is one of the possible ways to enhance the value of postconsumer plastic materials. However, the final performance of the recycled material will strongly depend on the quality of the selection made on the recycled product and on the degradation of the properties. In this context, the present study examines the effect of reprocessing for five successive extrusion cycles on the rheological, mechanical and thermal properties of a poly(butylene adipate-co-terephthalate) (PBAT)-based blend on samples reprocessed in both dry and wet conditions. The results showed that when the sample was processed after drying, degradation of the material was less than when it was processed i…
Toward the Decarbonization of Plastic: Monopolymer Blend of Virgin and Recycled Bio-Based, Biodegradable Polymer.
2022
Decarbonization of plastics is based on two main pillars: bio-based polymers and recycling. Mechanical recycling of biodegradable polymers could improve the social, economic and environmental impact of the use of these materials. In this regard, the aim of this study was to investigate whether concentrations of the same recycled biopolymer could significantly affect the rheological and mechanical properties of biodegradable monopolymer blends. Monopolymer blends are blends made of the same polymers, virgin and recycled. A sample of commercially available biodegradable blend was reprocessed in a single-screw extruder until two extrusion cycles were completed. These samples were exposed to gr…
Biocomposite PBAT/lignin blown films with enhanced photo-stability.
2022
Lignin can be obtained as a byproduct during cellulose-rich pulp fibers production and it is habitually treated as waste or intended for low-value destinations. However, due to UV absorption and mechanical properties, lignin can contribute to the fabrication of biodegradable blown films with superior performances. In this study, it was established the suitability of lignin for manufacturing biocomposite PBAT blown films with higher stiffness and photo-oxidation resistance. The effect of the filler concentration on the melt rheological behavior in non-isothermal elongational flow was investigated. The results allowed us to choose the correct filler concentration for producing films through a…
Durability of biodegradable polymers for the conservation of cultural heritage
2019
The use of polymers for conservation of cultural heritage is related to the possibility to slow down or stop natural deterioration which, in many cases, corresponds to stopping the entrance of liquid water and to favour spontaneous water vapour removal. Unfortunately, hydrophobicity is generally favoured by surface roughness and thus competitive with transparency. It is therefore important to find an optimal balance hydrophobicity, transparency and durability (especially to photooxidation). However, polymers typically used for applications in this field come from non-renewable resources and are not biodegradable. In this work, the mechanical, structural and optical properties of PLA, PBAT a…
Rheological, mechanical and morphological characterization of monopolymer blends made by virgin and photo-oxidized polypropylene
2021
In this work, monopolymer blends of virgin polypropylene and photo-oxidized polypropylene were prepare and characterized. The polypropylene samples were subjected to accelerated ageing to simulate the effects of outdoor exposure of polypropylene. After exposure, samples were pelletized and mixed with the same virgin polymer. The rheological, mechanical and morphological characterization was conducted on both the polymers and the blends. Both viscosity and mechanical properties decrease with increases in the content of recycled, photo-oxidized components and of the level of degradation of this component. In addition, the experimental data were compared with a model that takes into account bo…