Reactive compatibilization of PA6/LDPE blends with an ethylene–acrylic acid copolymer and a low molar mass bis-oxazoline
Abstract A sample of polyamide-6 (PA) was blended with low density polyethylene (LDPE) in the 80/20 wt/wt ratio, either without and with 2 phr of an ethylene–acrylic acid copolymer (EAA), Which was known to behave as a compatibilizer precursor, and the effect of the addition of small amounts (0.2 or 0.35 phr) of a fourth component, 2,2′-(1,3-phenylene)-bis(2-oxazoline) (PBO), was investigated. The reactions of PBO with EAA, PA and their blends were studied by recording as a function of time the torque applied to the blending apparatuses and by studying the solubility behavior of the products in formic acid. The PALDPE blends were prepared in a co-rotating twin screw extruder and were charac…
Torque rheometry investigation of model transreactions involving condensation polymers: I. Polyesters
The chemical transformations taking place when poly(ethylene terephthalate) (PET) or poly(ethylene naphthalate) (PEN) are blended in the melt with different low molar mass substances containing hydroxyl, carboxyl, or amine functional groups have been investigated as models of the transreactions, undergone by the polyesters in reactive blending operations. The polyester molecular weight changes caused by the alcoholysis, acidolysis, aminolysis, and esterolysis reactions have been monitored by torque-rheometry, using a Brabender Plasticorder static mixer. The degradation of the polyesters by hydrolysis was also studied, under similar conditions, by the addition of a water-releasing substance …
Effects of organoclay on morphology and properties of nanocomposites based on LDPE/PA-6 blends without and with SEBS-g-MA compatibilizer
LDPE/PA-6 blends (75/25 wt/wt) were added with SEBS-g-MA (S) and/or an organoclay (20A) using different compounding sequences and the morphology and the properties of the blends or composites were investigated. An XRD study of the nanocomposites with pure polymers showed that 20A is intercalated by LDPE or PA-6 chains, whereas it is exfoliated by S if the clay concentration does not exceed 10 wt%. The SEM investigation showed that both S and 20A behave as efficient emulsifying agents for the LDPE/PA-6 blends. However, their effect on the mechanical properties was found to be opposite: S enhanced toughness but lowered the stiffness, whereas 20A improved the elastic modulus but impaired the i…
Recycling of inside upholstery of end-of-life cars
A model study for the recycling of the interior upholstery plastic parts of end-of-life cars has been carried out by reprocessing the homogenized scraps of an upholstery farm in the presence of different compatibilizer precursors, such as an ethylene-glycidylmethacrylate copolymer (EGMA), a maleic anhydride functionalized thermoplastic elastomer (SEBS-MA), etc. The investigated scraps contained recycled polyethylene (from agricultural uses) and poly(ethylene terephthalate), as the main components, plus minor proportions of polypropylene, polyamide-6, and other additives, including an ethylene copolymer (EC), probably an ethylene-acrylic acid copolymer, which is used to compatibilize the car…
On the interlayer spacing collapse of Cloisite (R) 30B organoclay
Abstract When used as a nanofiller for the preparation of polymer/clay nanocomposites (PCNs), Cloisite® 30B (30B) often undergoes a d-spacing collapse, as demonstrated by a shift to wider angles of the XRD basal reflection. Such collapse has been variously attributed to organoclay contamination or, more often, to thermal degradation of the organic modifier with expulsion of the volatile products from the galleries. In this work, several PCNs loaded with 30B have been prepared by melt compounding, using different polymer matrices, and have subsequently been subjected to dissolution in appropriate solvents followed by precipitation in excess non-solvent and room temperature drying. An XRD ana…
Microstructure and rheological response of laboratory-aged SBS-modified bitumens
Polymer additives are widely used to improve the performance of road bitumens including their resistance to hardening during oxidation, although their oxidative inhibitor effect has not been well documented. This study aims to investigate the effect of laboratory-simulated ageing on the microstructure, and rheological properties of Polymer Modified Bitumens (PMBs) prepared with a Styrene-Butadiene-Styrene (SBS) copolymer and sulphur as a cross-linker. The laboratory ageing was conducted through the Rolling Thin Film Oven (RTFO) and the Pressure Aging Vessel (PAV) procedures. The unaged and aged binders were characterised using the Multiple Stress Creep and Recovery (MSCR) test, Gel Permeati…