0000000001062663
AUTHOR
Virgil Optasanu
Improve the dielectric properties of PrSrNi0.8Mn0.2O4 compounds by longer mechanical milling
Abstract Structural and dielectric properties of PrSrNi 0.8 Mn 0.2 O 4 ceramics elaborated by a rapid method combining mechanical milling and heat treatment were studied for the first time. The raw materials are milled at different times ( t mil = 0, 5, 10, 20 and 30 h) and annealed at 1300 °C for 8 h to produce a revealed PrSrNi 0.8 Mn 0.2 O 4 single phase, exhibiting tetragonal structure with space group I 4/ mmm . This result was confirmed by using the TEM/ED pattern for sample milled at 30 h using the [001] orientation. The corresponding lattice images show a well-ordered compound, indicating the absence of stacking faults and the growth of the crystallites. Giant dielectric response …
Structural, microstructural and dielectric studies in multiferroic LaSrNiO4-δ prepared by mechanical milling method
Abstract The solid solution LaSrNiO 4-δ has been successfully prepared by a rapid method combining mechanical milling and heat treatment. The structure and microstructure transformations were characterized by X-ray powder diffraction, scanning and transmission electron microscopy. The dielectric property was also investigated. After 10 h of milling and 8 h of heat treatment at 1300 °C, X-ray diffraction analysis revealed LaSrNiO 4-δ single phase, exhibiting tetragonal structure with space group of I4/mmm. This result was confirmed by using the ED pattern for sample using the [001] orientation. The corresponding lattice images show the compound to be well ordered, indicating the absence of s…
Dielectric relaxation and polaronic hopping in Mn-substituted LaSrNiO4 nickelates prepared by mechanical milling method
Abstract The structures, microstructures and dielectric properties of LaSrNi1−xMnxO4 (x = 0, 0.1, 0.2, 0.3 and 0.5) ceramics synthetized by mechanical milling followed by heat treatment were studied. One single tetragonal phase was revealed in all compounds. Structural parameters were obtained by Rietveld refinement. The substitution of Ni ions by Mn produces a variation of the lattice parameters but no phase change is observed. The surface morphology and elemental analysis of these samples were respectively investigated by Scanning Electron Microscopy (SEM) and energy dispersive X-ray technique (EDS). Giant dielectric response was observed in these ceramics, and at least two relaxations we…
A Mechano-Chemical Coupling for Hydrogen Diffusion in Metals Based on a Thermodynamic Approach
Hydrogen diffusion in metals is still an ongoing topic of research due to its technical relevance (hydrogen embrittlement, hydrogen storage...). In the last decades, significant progress in understanding the time evolution of the hydrogen concentration in solids was completed. This paper presents a modeling of hydrogen diffusion with a general and thermodynamically based diffusion concept coupled with mechanical and chemical aspects. This model was previously used to simulate the oxidation of a metal [1][2]. This concept has been upgraded to offer a thoroughly macroscopic behavior law used to simulate hydrogen diffusion in metal parts under mechanical loadings. The thermodynamic approach of…
Improving the high temperature (HT) oxidation resistance of a Beta-Titanium alloys by mechanical treatments
International audience
Improving the high temperature oxidation resistance of pure titanium by shot-peening treatments
International audience; Shot-peening (SP) treatments have shown their capacity to improve the oxidation resistance of titanium and zirconium thanks to the large compressive stresses and the surface hardening induced by this mechanical process. However, shot-peening treatments can produce a surface chemical deposit, which can modify the high temperature oxidation resistance. Here, we study pure titanium samples shot-peened with different type of balls: tungsten carbide, alumina or glass. The oxidation behavior was studied at 700 °C in dry air by thermo gravimetric analysis for short isotherm oxidation periods up to 100 h. Also, long oxidation tests (3000 h) at 700 °C were performed with an i…
Influence of surface Shock-peening treatment on high temperature oxidation of Titanium
International audience
Impact of rolling conditions on the hydriding of grade 2 titanium welded tubes
In this article, we study the impact of rolling conditions on the texture of the commercially pure titanium grade 2. In a previous work, NEOTISS in collaboration with ICB laboratory, shown that the texture highly influences the precipitation of hydrides in Titanium. In order to create different textures, Titanium sheets grade 2 are cold rolled asymmetrically and symmetrically with or without lubricant. The inverse pole figures and direct pole figures obtained allow us to deduce that symmetrical cold rolling does not change the grains orientation but generates a rotation of grains along c-axis (normal to basal plan). However, asymmetrical cold rolling leads to the formation of a new crystall…
Pre-Stressed Sub-Surface Contribution on Bulk Diffusion in Metallic Solids
Our recent modelling works and corresponding numerical simulations realized to describe the UO2 oxidation processes confirm the theory showing that an applied mechanical strain can strongly affect the local oxygen diffusion in a stressed solid. This result allows us to assume that stress field, previously applied at the surface of a metallic sample on several microns, will delay the degradation during its oxidation. Considering this hypothesis, we implemented a FEM simulation code developed in our laboratory to numerically investigate some different stress fields applied on a sample sub-surface, that might significantly modify the volume diffusion of oxygen during the oxidation process. The…
Improving the high temperature oxidation resistance of Ti-β21S by mechanical surface treatment
The improvement of the high temperature oxidation resistance of titanium alloys is currently a technological challenge. Mechanical surface treatments as shot-peening (SP) have shown their ability to improve the behaviour of pure zirconium and titanium. However, shot-peening treatments can induce a significant surface contamination. Laser shock peening (LSP) appears as a good alternative. Here, we have investigated the effect of SP and LSP treatments on the HT oxidation behavior of Ti-β21S. Samples treated by these methods have been compared to untreated ones for long exposures (3000 h) at 700 °C in dry air. The samples placed in a furnace at 700 °C were periodically extracted to be weighed.…
Influence of the U3O7 domain structure on cracking during the oxidation of UO2
Abstract Cracking is observed when a UO 2 single crystal is oxidised in air. Previous studies led to the hypothesis that cracking occurs once a critical depth of U 3 O 7 oxidised layer is reached. We present some μ-Laue X-ray diffraction results, which evidence that the U 3 O 7 layer, grown by topotaxy on UO 2 , is made of domains with different crystalline orientations. This observation was used to perform a modelling of oxidation coupling chemical and mechanical parameters, which showed that the domain patterning induces stress localisation. This result is discussed in comparison with stress localisation observed in thin layer deposited on a substrate and used to propose an interpretation…
Machine Learning Approaches for Activity Recognition and/or Activity Prediction in Locomotion Assistive Devices—A Systematic Review
Locomotion assistive devices equipped with a microprocessor can potentially automatically adapt their behavior when the user is transitioning from one locomotion mode to another. Many developments in the field have come from machine learning driven controllers on locomotion assistive devices that recognize/predict the current locomotion mode or the upcoming one. This review synthesizes the machine learning algorithms designed to recognize or to predict a locomotion mode in order to automatically adapt the behavior of a locomotion assistive device. A systematic review was conducted on the Web of Science and MEDLINE databases (as well as in the retrieved papers) to identify articles published…
Enhancement of the dielectric response through Al-substitution in La1.6Sr0.4NiO4 nickelates
The structures and dielectric properties of La1.6Sr0.4Ni1−xAlxO4 (x = 0, 0.2 and 0.4) ceramics elaborated using the Pechini method were studied for the first time. The same unique tetragonal phase was found in all compounds. The lattice parameters were found using Rietveld refinement. The surface morphology characterization and elemental analysis of these samples were respectively carried out using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A giant dielectric response was observed in these ceramics, and one dielectric relaxation was found. The substitution of nickel with aluminum results in a colossal dielectric constant value (>106). The dielectric l…
Retarding the high temperature oxidation of Titanium by shot-peening surface treatment
International audience
High-resolution characterization of the diffusion of light chemical elements in metallic components by scanning microwave microscopy
International audience; An original sub-surface, high spatial resolution tomographic technique based on scanning microwave microscopy (SMM) is used to visualize in-depth materials with different chemical compositions. A significant phase difference in SMM between aluminum and chromium buried patterns has been observed. Moreover this technique was used to characterize a solid solution of a light chemical element (oxygen) in a metal lattice (zirconium). The large solubility of the oxygen in zirconium leads to modifications of the properties of the solid solution that can be measured by the phase shift signal in the SMM technique. The signal obtained in cross-section of an oxidized Zr sample s…
Influence of the Residual Stresses Induced by Shot-Peening on the Oxidation of Zr Plates
The present study evaluates the influence of the residual stress on the oxidation rate of Zr at 650°C. It is shown that the oxidation rate can be substantially decreased by shot-peening. A systematic instigation of the various factors (such as the residual stress, the surface pollution and the chemical composition of the oxidation atmosphere) is realized to separate their influence on the oxidation. The influence of an annealing made after the shot-peening is also considered. One show that the pollution of the surface during the shot-peening process is not responsible for the oxidation rate decrease.
Kinetics study of mechanically treated pure titanium with enhancement of the high temperature oxidation resistance
International audience
Role of nitrogen in the high temperature oxidation of mechanically treated pure titanium
International audience
EBSD, XRD and SRS characterization of a casting Al-7wt%Si alloy processed by equal channel angular extrusion: Dislocation density evaluation
Abstract Aluminum‑silicon (Al Si) alloys of high silicon contents are composite materials; they are used whenever high casting properties are required. They are slightly ductile below 8wt%Si. An increase in ductility can be obtained by refining Si-crystals in elaboration or by a further hot working. In the present work, an Al-7wt%Si alloy was processed by Equal Channel Angular Extrusion (ECAE) at temperatures 20 °C and 160 °C up to three passes. The die was formed by two cylindrical channels with characteristic angles Φ = 110° and Ψ = 0. EBSD, X ray diffraction (XRD) and Strain Rate Sensitivity (SRS) were used to characterize the microstructure and the mechanical properties. High levels of …