Search results for " Catalyst"

Photocatalytic and Catalytic Oxidation of 2-Propanol over Au/TiO2-CeO2 Catalysts

2016

Photocatalytic and catalytic oxidation of 2-propanol (representative VOC’s compound) were compared over mixed (Au)TiO2-CeO2-based catalysts. The role of support in Au catalyzed oxidation reaction under photo and dark conditions was studied. In the photocatalytic oxidation CeO2 had a negative effect on the performance towards the alcohol conversion of both TiO2-CeO2 and Au/TiO2-CeO2 catalysts, being Au/TiO2 the most active system. On the contrary mixed TiO2-CeO2 and Au/TiO2- CeO2 samples showed a higher catalytic oxidation efficiency for 2-propanol conversion compared to the single oxides.

Iminium Catalysis (n → π*)

2016

Enhanced NiO Dispersion on a High Surface Area Pillared Heterostructure Covered by Niobium Leads to Optimal Behaviour in the Oxidative Dehydrogenatio…

2020

[EN] A Nb-containing siliceous porous clay heterostructure (PCH) with Nb contents from 0 to 30 wt %) was prepared from a bentonite and used as support in the preparation of supported NiO catalysts with NiO loading from 15 to 80 wt %. Supports and NiO-containing catalysts were characterised by several physicochemical techniques and tested in the oxidative dehydrogenation (ODH) of ethane. The characterisation studies on Nb-containing supports showed the presence of well-anchored Nb(5+)species without the formation of Nb(2)O(5)crystals. High dispersion of nickel oxide with low crystallinity was observed for the Nb-containing PCH supports. In addition, when NiO is supported on these Nb-containi…

Supported Polyhedral Oligomeric Silsesquioxane-Based (POSS) Materials as Highly Active Organocatalysts for the Conversion of CO2

2018

Very high turnover numbers (TON) and productivity values up to 7875 and 740 respectively have been obtained for the conversion of CO2 into cyclic carbonates by using hybrid materials based on imidazolium modified polyhedral oligomeric silsesquioxanes (POSS-Imi) grafted on amorphous silica (SiO2) and mesostructured SBA-15. The heterogeneous organocatalysts were easily prepared via a straightforward synthetic procedure allowing to generate high local concentration spots of imidazolium active sites surrounding the POSS core. This synthetic procedure is also a promising approach for the design of a wide library of hybrid functional materials. The materials do not possess other co-catalytic spec…

Catalytic Carbonylative Double Cyclization of 2-(3-Hydroxy-1-yn-1-yl)phenols in Ionic Liquids Leading to Furobenzofuranone Derivatives

2019

A catalytic carbonylative double cyclization method for the synthesis of furo[3,4-b]benzofuran-1(3H)-ones is reported. It is based on the reaction between readily available 2-(3-hydroxy-1-yn-1-yl)phenols, CO, and oxygen carried out in the presence of catalytic amounts of PdI2 (1 mol %) in conjunction with KI (20 mol %) and 2 equiv of diisopropylethylamine at 80 degrees C for 24 h under 30 atm of a 1:4 mixture of CO-air. Interestingly, the process was not selective when carried out in classical organic non-nucleophilic solvents (such as MeCN or DME), leading to a mixture of the benzofurofuranone derivative and the benzofuran ensuing from simple cycloisomerization, whereas it turned out chemo…

Electrochemical Arylation Reaction

2018

Arylated products are found in various fields of chemistry and represent essential entities for many applications. Therefore, the formation of this structural feature represents a central issue of contemporary organic synthesis. By the action of electricity the necessity of leaving groups, metal catalysts, stoichiometric oxidizers, or reducing agents can be omitted in part or even completely. The replacement of conventional reagents by sustainable electricity not only will be environmentally benign but also allows significant short cuts in electrochemical synthesis. In addition, this methodology can be considered as inherently safe. The current survey is organized in cathodic and anodic con…

Sewage sludge as cheap alternative to microalgae as feedstock of catalytic hydrothermal liquefaction processes

2019

Abstract Production of biocrude through hydrothermal liquefaction (HTL) of sewage sludge (SS) and Chlorella vulgaris was investigated. NiMo/Al2O3 (KF 851), CoMo/Al2O3 (KF 1022) and activated carbon felt, tested as catalysts at 598 K for 30 min, did not change the biocrude yield but significantly improved its quality. Quantitative sulfur removal and lower oxygen content were found in biocrude when KF 851 and KF 1022 were used with C. vulgaris. The same catalysts decreased O/C and S/C ratio of the biocrude from SS. The highest HHV (38.19 MJ/kg) and H/C ratio (1.65) and the lowest O/C (0.11) of the biocrude from SS were obtained with the cheaper activated carbon felt. A new product phase, prob…

Sustainable Construction of Heterocyclic 1,2,3-Triazoles by Strict Click [3+2] Cycloaddition Reactions Between Azides and Alkynes on Copper/Carbon in…

2019

1,4-Disubstituted-1,2,3-triazoles, considered as an important and useful class of heterocycles with potential applications in material science and biology, have been prepared in an efficient and selective manner by copper on carbon-catalyzed [3+2] cycloaddition reactions of azides and alkynes (CuAAC) in water under strict click chemistry conditions. Copper(I) catalysts heterogenized onto commercially activated carbon materials (Cu-CC) and on another carbon material produced from vegetable biomass using Argan nut shells (Cu-CANS) were found to be versatile catalytic sources for sustainable CuAAC. These copper on carbon supports were prepared and fully characterized by using two types of acti…

ChemInform Abstract: Recyclable Catalyst Reservoir: Oxidation of Alcohols Mediated by Noncovalently Supported Bis(imidazolium)-Tagged 2,2,6,6-Tetrame…

2014

3D Printed Palladium Catalyst for Suzuki-Miyaura Cross-coupling Reactions

2020

Selective laser sintering (SLS) 3d printing was utilized to manufacture a solid catalyst for Suzuki-Miyaura cross-coupling reactions from polypropylene as a base material and palladium nanoparticles on silica (SilicaCat Pd(0)R815-100 by SiliCycle) as the catalytically active additive. The 3d printed catalyst showed similar activity to that of the pristine powdery commercial catalyst, but with improved practical recoverability and reduced leaching of palladium into solution. Recycling of the printed catalyst led to increase of the induction period of the reactions, attributed to the pseudo-homogeneous catalysis. The reaction is initiated by oxidative addition of aryl iodide to palladium nano…