Search results for " MIC"
showing 10 items of 11429 documents
Effect of high hydrostatic pressure on extraction of B-phycoerythrin from Porphyridium cruentum: Use of confocal microscopy and image processing
2019
International audience; The aim of the study was to extract B-phycoerythrin from Porphyridium cruentum while preserving its structure. The high hydrostatic pressure treatments were chosen as extraction technology. Different methods have been used to observe the effects of the treatment: spectrophotometry and confocal laser scanning microscopy followed by image processing analysis. Image processing led to the generation of masks used for the identification of three clusters: intra, extra and intercellular. All methods showed that high hydrostatic pressure treatments between 50 and 500 MPa failed to extract B-phycoerythrin from Porphyridium cruentum cells. The fluorescence emission was negati…
Occurrence of antibiotics and antiretroviral drugs in source-separated urine, groundwater, surface water and wastewater in the peri-urban area of Chu…
2020
Recently, there has been an increased interest in bridging the knowledge gap in the occurrence and fate of pharmaceuticals in African urban water cycles. In this study, the occurrence of 7 antibiotics and 3 antiretrovirals in source-separated urine, groundwater, wastewater and surface water of the peri-urban area of Chunga in Lusaka, Zambia, was studied. In groundwater, the pharmaceuticals were only sporadically present with 4 antibiotics and 1 antiretroviral detected. The concentration of the antibiotics ranged from below limit of quantification (<LOQ) to 880 ng/L, with sulfamethoxazole having the highest detection frequency of 42.3%. In the surface water, a comparatively high concentrati…
Experimental results on the economic management of a smart microgrid
2020
The aim of this paper is to assess economic benefits deriving from the adoption of a smart microgrid. To this end, a case study consisting of 250 houses connected to the distribution network through a MV/LV transformer substation has been investigated and implemented in the experimental microgrid built at the Polytechnic University of Bari, Italy. The analysis has been performed by comparing three different energy providers: the utility grid, the utility grid with the inclusion of non-programmable renewables generators, and the inclusion of such residential loads into a smart microgrid. The obtained results demonstrated that with the adoption of a smart microgrid significant costs savings c…
Surface and mechanical characterization of stationary shoulder friction stir welded lap joints: experimental and numerical approach
2020
Friction Stir Welding (FSW) is one of the most used solid-state welding processes in the aeronautical, aerospace, ground transportation and naval fields. Stationary Shoulder Friction Stir Welding (SSFSW) is a recently introduced variant of the process allowing lower heat input into the joints, with beneficial effects in terms of joint mechanical properties, microstructure and top surface finish. In the paper, lap joints produced by SSFSW and made out of AA6082-T6 aluminum alloy sheets have been analyzed with the aim to investigate the effect of the stationary shoulder on the lap joints surface, metallurgical, and mechanical properties. The lap joints produced by SSFSW have been compared to …
Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H 3 PO 4 /H 2 SO 4
2017
Abstract In recent decades, new manufacturing processes have been developed such as Thermal Spray Coating (TSC) and Additive Layer Manufacturing (ALM), which reduce or avoid machining of parts with complex geometries. This study aims to develop an Electropolishing (EP) process for TSC and ALM 316L Stainless Steel (SS). EP is an anodic dissolution process currently used in industry to reduce surface roughness and obtain a bright and smooth finish. The EP mechanism was studied, in a mixture of H3PO4 and H2SO4, for TSC, ALM and “cast” SS in order to determine the best conditions (time, temperature, potential). Special attention was paid to surface characterization by combining several techniqu…
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
Direct laser welding of pure titanium to austenitic stainless steel
2018
Abstract Direct butt joining of pure titanium to 316L stainless steel with continuous Yb:YAG laser was performed with variation of the beam offset from joint line. Mechanical properties of samples were evaluated by tensile tests and three-point flexural tests. The fractured surfaces and cross sections of welds were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Tensile properties of welds were strongly determined by the beam offset from joint line and are well described by Weibull statistics. Ultimate tensile strength of 174 ± 69 MPa and ultimate flexural strength of 297 ± 48 MPa were obtained. Brittle fracture took place in…
Impact des conditions d'usinage sur la zone du matériau affectée par le procédé
2007
Colloque avec actes et comité de lecture. Internationale.; International audience; Les procédés d'usinage peuvent créer des contraintes résiduelles à la surface des pièces usinées et ainsi modifier la microstructure et la texture de la matière proche de la surface. De tels changements sont importants pour l'étude du comportement des pièces au cours du temps. Il est alors nécessaire de quantifier les contraintes résiduelles, les composantes de texture et de déterminer la microstructure induite par l'usinage pour comprendre et prédire le comportement des surfaces considérées. Dans cette étude, le matériau cuivre pur a été choisi et considéré comme un "système modèle". En tournage, l'influence…
Application of linear friction welding for joining ultrafine grained aluminium
2020
Abstract Ultrafine grained (UFG) materials are of great potential in industry due to their enhanced mechanical strength and other promising features, such as ability to superplastic deformation or excellent corrosion resistance. Nevertheless, one of the main limitations lies in their low thermal stability, which leads to excessive grain growth at elevated temperature. It influences mainly further processes performed at high temperature, such as joining. It causes detrimental problems during conventional fusion welding, as significant grain growth is observed and therefore the advantages as a result of small average grain size disappear. Therefore, the idea of applying solid state joining pr…
Crowd-Averse Robust Mean-Field Games: Approximation via State Space Extension
2016
We consider a population of dynamic agents, also referred to as players. The state of each player evolves according to a linear stochastic differential equation driven by a Brownian motion and under the influence of a control and an adversarial disturbance. Every player minimizes a cost functional which involves quadratic terms on state and control plus a cross-coupling mean-field term measuring the congestion resulting from the collective behavior, which motivates the term “crowd-averse.” Motivations for this model are analyzed and discussed in three main contexts: a stock market application, a production engineering example, and a dynamic demand management problem in power systems. For th…