Search results for " Materials Science"

Laser Ultrasonics Inspection for Defect Evaluation on Train Wheel

2019

Abstract Passengers’ safety and in-service life of wheelset axles play an important role in railway vehicles. For this reason, periodic inspections are necessary. Among non-destructive techniques, ultrasonic ones are widely applied in this field. The main disadvantage of conventional ultrasonic techniques is that the overall inspection of wheels requires the train to be put out-of-service and disassembly each part, which is time-consuming and expensive. In this paper, a non-conventional non-contact laser ultrasonic inspection for train wheels is proposed. The proposed method uses a laser interferometer to receive the ultrasonic wave without contact. The receiving system allows choosing the …

Cold gas dynamic spray additive manufacturing today: Deposit possibilities, technological solutions and viable applications

2017

This paper reports the current potentials of cold gas dynamic spraying (CGDS). CGDS has been significantly developed to produce several functional solutions categorized as follows: deposits with a single powder nature, composites-based deposits, nanotechnological deposits and hybrid coating/substrate assemblies. CGDS process has improved in proficiency and is still gaining attention from scientists and industry. Covering a wide range of materials, both standard and advanced, this additive manufacturing process offers substantial applications for surface functionalization, structural or dimensional restoration, bulk production providing specific material properties, and art/decoration. Progr…

Metallurgical Strategies for the Joining of Titanium Alloys with Steels

2018

Physical properties and microstructure characteristics of (1–x)BaTiO3–xCaTiO3 systems

2018

The study investigates the microstructure, thermal and mechanical properties of (1–x)BaTiO3–xCaTiO3 ((1–x)BT–xCT)) (x = 0.01, 0.04, 0.08) samples. The BT–CT system to be tested was formed as a soli...

Spark Plasma Sintering à partir de poudres mécaniquement activées : compréhension des transitions de phase au cours d'un frittage réactif

2007

International audience; À " basse température " (entre 400 et 600 ◦C), l'oxydation de MoSi2 entraîne sa désintégration en poudre (phénomène de " peste "). De récents travaux ont montré que l'utilisation de MoSi2 dense et nano-organisé permettrait de ralentir ce phénomène de " peste ". Le défi de produire des matériaux denses et nano-organisés peut être relevé par le frittage " flash " réactif sous champ électrique à partir des poudres mécaniquement activées (Mechanically-Activated Spark Plasma Sintering, MASPS). Le contrôle de la composition et de la microstructure du composé intermétallique MoSi2 nécessite de déterminer les paramètres du frittage SPS (température, rampe de montée en tempér…

Electrical transport in lead-free (Na0.5Bi0.5)1–xSrxTiO3 ceramics (x = 0, 0.01 and 0.02)

2017

Lead-free (Na0.5Bi0.5)1xSrxTiO3 (x = 0, 0.01 and 0.02) ceramics were manufactured through a solid-state mixed oxide method and their ac (σac) and dc (σdc) electric conductivity were studied. It is ...

Characteristics of industrially manufactured amorphous hydrogenated carbon (a-C:H) depositions on high-density polyethylene

2016

Industrially high-density polyethylene (HDPE) was successively covered by two types of amorphous hydrogenated carbon (a-C:H) films, one more flexible (f-type) and the other more robust (r-type). The films have been grown by radio frequency plasma-enhanced chemical vapor deposition (RF-PECVD) technique with acetylene plasma. The surface morphology of both types has been studied by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Contact angle measurements and Raman spectroscopy analysis were done to investigate the surface wettability and carbon chemical composition. Both types display similar morphology and grain growth pattern. Contact angle measurements revealed surfa…

Ultra-Wide Band Gap in Two-Dimensional Phononic Crystal with Combined Convex and Concave Holes

2017

A phononic crystal with an ultra‐wide band gap is proposed, whose unit cell consists of a cross‐like concave hole in the center and four square convex holes at the corners. The dispersion relations, modal kinetic energy ratio, and eigenmodes at edges of the band gaps are investigated by using the finite element method. The influence of the geometrical parameters of the convex and concave holes on the band gaps is further analyzed. After optimization, an ultra‐wide band gap with gap‐to‐midgap ratio of 156.0% is achieved, with the filling fraction keeping a relative small value. Numerical results illustrate that the combination of convex and concave holes is a practicable direction for struct…

Barrier inhomogeneity in vertical Schottky diodes on free standing gallium nitride

2019

Abstract In this paper, the electrical behavior of a Ni/Au Schottky barrier on free standing GaN has been studied employing a variety of techniques and correlated with the material and interface quality. The temperature dependence of the ideality factor (n) and of the Schottky barrier height (ΦB) revealed a spatial inhomogeneity of the barrier. This behavior has been described by means of the Tung's model on inhomogeneous Schottky barriers. The origin of the barrier inhomogeneity can be likely associated to the surface quality of the GaN epilayer or to microstructure of the Ni/GaN interface.

EBSD, XRD and SRS characterization of a casting Al-7wt%Si alloy processed by equal channel angular extrusion: Dislocation density evaluation

2019

Abstract Aluminum‑silicon (Al Si) alloys of high silicon contents are composite materials; they are used whenever high casting properties are required. They are slightly ductile below 8wt%Si. An increase in ductility can be obtained by refining Si-crystals in elaboration or by a further hot working. In the present work, an Al-7wt%Si alloy was processed by Equal Channel Angular Extrusion (ECAE) at temperatures 20 °C and 160 °C up to three passes. The die was formed by two cylindrical channels with characteristic angles Φ = 110° and Ψ = 0. EBSD, X ray diffraction (XRD) and Strain Rate Sensitivity (SRS) were used to characterize the microstructure and the mechanical properties. High levels of …