Search results for " Nanotube"

Conduction properties of thin films from a water soluble carbon nanotube/hemicellulose complex.

2018

We have examined the conductive properties of carbon nanotube based thin films, which were prepared via dispersion in water by non-covalent functionalization of the nanotubes with xylan, a type of hemicellulose. Measurements of low temperature conductivity, Kelvin probe force microscopy, and high frequency (THz) conductivity elucidated the intra-tube and inter-tube charge transport processes in this material. The measurements show excellent conductive properties of the as prepared thin films, with bulk conductivity up to 2000 S cm−1. The transport results demonstrate that the hemicellulose does not seriously interfere with the inter-tube conductance. peerReviewed

Experimental studies on carbon nanotubes and graphene functionalized via physical adsorption with cellulose and avidin

2018

In this Thesis I have experimentally studied structural, electronic, and optical properties of hybrids of nanocarbon materials, carbon nanotubes (CNT) and graphene, and certain biomacromolecules. The latter are especially xylan, a type of hemicellulose, and avidin, an important protein. Complexes of CNT with hemicellulose are attractive because the hybrid material is soluble in water. The conductive transport properties of thin films of CNT /hemicellulose have been systematically studied with different experimental tools. These are low temperature DC conduction measurements, Kelvin probe microscopy, and optical conductivity measurements at terahertz frequencies. The results clearly indicate …

Surface and interface effects on the current-voltage characteristic curves of multiwall carbon nanotube-Si hybrid junctions selectively probed throug…

2021

The possibility to increase the efficiency of photovoltaic (PV) cells based on hybrid carbon nanotube (CNT)–Si heterojunctions is related to the ability to control the chemical properties of the CNT–Si interface and of the CNT bundle layer. In spite of the encouraging performances of PV cells based on multiwall (MW) CNT, so far few efforts have been made in the study of this device compared to single wall (SW) CNT–Si interfaces. Here, surface and interface effects on the current–voltage characteristic curves of MW CNT–Si hybrid junctions are investigated through exposure to HF vapors and to 10 ppm-NO2 and compared to the effects detected in SW CNT–Si junctions. Quite similar results in term…

Halloysite Nanotubes Coated by Chitosan for the Controlled Release of Khellin

2020

In this work, we have developed a novel strategy to prepare hybrid nanostructures with controlled release properties towards khellin by exploiting the electrostatic interactions between chitosan and halloysite nanotubes (HNT). Firstly, khellin was loaded into the HNT lumen by the vacuum-assisted procedure. The drug confinement within the halloysite cavity has been proved by water contact angle experiments on the HNT/khellin tablets. Therefore, the loaded nanotubes were coated with chitosan as a consequence of the attractions between the cationic biopolymer and the halloysite outer surface, which is negatively charged in a wide pH range. The effect of the ionic strength of the aqueous medium…

Tubular Nanocontainers for Drug Delivery

2018

Fabrication and characterization of Metal and Metal Oxide Nanostructures Grown by metal displacement deposition into anodic alumina membranes

2011

Abstract preview not available - see full-text PDF article.

Carbon nanotube azafullerene peapods and their electronic transport properties

2008

Nanocomposites based on UHMWPE and α-tocopherol-CNTs: processing and characterization

2013

Polymer/CNTs nanocomposite fibres

2010

Plasma Functionalization of Multiwalled Carbon Nanotubes and Their Use in the Preparation of Nylon 6-Based Nanohybrids

2012

The possibility to obtain carbon nanotubes (CNT)/polyamide 6 composites with excellent mechanical properties in a simple, industrially scalable way is investigated. Commercial CNTs are treated by plasma while changing some key parameters (exposure time, plasma power, type of gas) in order to optimize the process and to achieve a sufficient degree of functionalization. The treated samples are characterized by Fourier transform infrared spectroscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. The most interesting samples are selected to be used as reinforcing fillers, in different concentrations, in a polyamide 6 matrix. The mechanical tests show a dramatic increase of both tens…