Search results for " Plastic"

Hydrothermal aging of carbon reinforced epoxy laminates with nanofibrous mats as toughening interlayers

2016

Electrospun mats have been applied as toughening interlayers in high performance carbon fiber epoxy composites. While the toughening mechanism exerted by the mat at the interface is the subject of several recent studies, no investigations are reported on the aging behaviour of laminates comprising these nanostructured elements. This work investigates the influence of the combined effect of water and temperature (90 °C) on laminates with Nylon 6,6 electrospun membranes placed either at the middle plane only or at each interlayer. The water-uptake behaviour is modelled by a two-stage diffusion model and compared with the behaviour of the neat resin and of the laminate without mats. Interestin…

Long-term properties and end-of-life of polymers from renewable resources

2017

[EN] The long-term properties and end-of-life of polymers are not antagonist issues. They actually are inherently linked by the duality between durability and degradation. The control of the service-todisposal pathway at useful performance, along with low-impact disposal represents an added-value. Therefore, the routes of design, production, and discarding of bio-based polymers must be carefully strategized. In this sense, the combination of proper valorisation techniques, i.e. material, energetic and/ or biological at the most appropriate stage should be targeted. Thus, the consideration of the end-of-life of a material for a specific application, instead of the end-of-life of a material s…

Modelling Aspects in Accumulative Roll Bonding Process by Explicit Finite Element Analysis

2013

Accumulative Roll-Bonding (ARB) process is a severe plastic deformation (SPD) process, capable of developing grains below 1 μm in diameter and improving mechanical properties of the material. In this study, the authors compared two different FE-codes with respect of its applicability for numerical analysis of the ARB process. Modelling this process was achieved using the explicit code for Abaqus/CAE both in 2D and 3D. The proposed model was used to assess the impact of ARB cycles on the final material properties. The numerical results in 2D and 3D were compared and contrasted. The research work presented in this paper is focused on the simulation optimization based on CPU time minimization.…

Automatic Recognition and Analysis of Scanned Non-crimp Fabrics for Calculation of their Fluid Flow Permeability

2007

Automatic recognition of scanned images of distorted bi-axial fiber bundle arrangements is considered in order to obtain the overall permeability of the formed fiber network. Scanned images are pre-processed with color normalization followed by usage of a threshold to find the pixels belonging to the bundles, the threads keeping the bundles together, and the distinct gaps formed between the bundles. Since the scanned images virtually have a perfect grayscale, the intensity can be treated as a corresponding signal of the image. Next the regular character of the fiber network is investigated using Fourier analysis on the fiber bundles as well as on the threads. The direction, position, and s…

Dynamic characterization for the dielectric electroactive polymer fundamental sheet

2012

Published version of an article published in the journal: International Journal of Advanced Manufacturing Technology. Also available from the publisher at: http://dx.doi.org/10.1007/s00170-012-4423-6 A study into the appropriateness of characterizing the dynamics of the dielectric electroactive polymer (DEAP) fundamental sheet has been performed. Whereby a model describing the dynamics of the DEAP fundamental sheet is developed, parameters of the models are determined using experimental/simulation results, and verification has been conducted to determine the precision of the dynamic model. The precision for the DEAP sheet-obtained dynamic model could not be verified unless some parameters c…

New Computational Fluid Dynamic Procedure to Estimate Friction and Local Losses in Coextruded Drip Laterals

2007

The design of trickle irrigation systems is crucial to optimize profitability and to warrant high values for the emission uniformity (EU) coefficient. EU depends on variation of the pressure head due to head losses along the lines and elevation changes, as well as the water temperature, and other parameters related to the emitters (manufacturer's coefficient of variation, number of emitters per plants, emitter spacing). Trickle irrigation plants are usually designed using small diameter plastic pipes (polyethylene or polyvinyl chloride). The design problem, therefore, needs to consider head losses along the lines as well as emitter discharge variations due to the manufacturer's variability.…

Erratum to: Letter to the Editor [Engineering Fracture Mechanics 2003 (70) 1219-21]

2004

Erratum and Corrections

Structural Performances of Composite Pultruded GFRP Emergency Structures

2021

The use of composite FRP pultruded elements in civil constructions is nowadays widely accepted as a valid alternative to classic materials. In the case of emergency applications (as for temporary shelter after earthquakes, floods and all disastrous), the lightness, ease of transport, assembly, safety of use, possibility of disassembly and reuse are key aspects that composite FRP structures can provide easily.

Macromolecules in Microfluidics: A Synergy for Systems Engineering

2017

Concrete softening effects on the axial capacity of RC jacketed circular columns

2016

Abstract Among the different strengthening techniques to repair RC structures, reinforced concrete (RC) jacketing is one of the most commonly adopted, especially for columns. Its wide application is due to its easy application and relatively reduced cost with respect to other methods (e.g. FRP wrapping, Shape Memory Alloy active confinement). The target of RC jacketing is to increase axial, flexural capacity and ductility of weak existing members by means of two main effects: confinement action provided by the jacket and composite action between external jacket and inner concrete. Different theoretical studies have been carried out to calculate the strength enhancement due to confinement ac…