Search results for " ROUGH."
showing 10 items of 200 documents
In situ angular measurements of thermal infrared sea surface emissivity—Validation of models
2005
Abstract In this paper, sea surface emissivity (SSE) measurements obtained from thermal infrared radiance data are presented. These measurements were carried out from a fixed oilrig under open sea conditions in the Mediterranean Sea during the WInd and Salinity Experiment 2000 (WISE 2000). The SSE retrieval methodology uses quasi-simultaneous measurements of the radiance coming from the sea surface and the downwelling sky radiance, in addition to the sea surface temperature (SST). The radiometric data were acquired by a CIMEL ELECTRONIQUE CE 312 radiometer, with four channels placed in the 8–14 μm region. The sea temperature was measured with high-precision thermal probes located on oceanog…
Calculus of Contextual Rough Sets in Contextual Spaces
1998
ABSTRACT The palier explains the methods of approximation of set which were earlier put forth by the authors (1995a, 1995b) and by W. Marek and H. Rasiowa (1986). An essential part of this paper is devoted to the presentation of a certain calculus of rough sets and contextual rough sets in contextual spaces.
SURFACE ROUGHNESS PREDICTION OF ELECTRO-DISCHARGE MACHINED COMPONENTS USING ARTIFICIAL NEURAL NETWORKS
2016
Electro-Discharge machining (EDM) is a thermal process comprising a complex metal removal mechanism, which involves the formation of a plasma channel between the tool and the workpiece electrodes leading to the melting and evaporation of the material to be removed. EDM is considered especially suitable for machining complex contours with high accuracy, as well as for materials that are not amenable to conventional removal methods. However, several phenomena negatively affecting the surface integrity of EDMed workpieces need to be taken into account and studied in order to achieve the optimization of the process. Recently, artificial neural networks (ANN) have emerged as a novel modeling tec…
STUDIO DI UN AMMORTIZZATORE ELETTROMAGNETICO A RECUPERO DI ENERGIA
2013
Questo lavoro ha come obiettivo principale lo studio teorico e con supporto di software F.E.M. di un dispositivo che consenta recupero energetico da una sospensione automobilistica. In sostituzione allo smorzatore viscoso, che dissipa l’energia cinetica del veicolo a seguito dell’attraversamento di strade sconnesse o ostacoli più marcati, si è usato uno smorzatore elettromagnetico che svolga le funzioni dello smorzatore viscoso consentendo un recupero di energia elettrica. Lo smorzatore elettromagnetico è di tipo a magneti permanenti e il suo funzionamento si basa sul fenomeno dell’induzione elettromagnetica. Il modello matematico descrive il funzionamento dello smorzatore, restituendo i va…
An in vitro evaluation of the effect of sandblasting and laser surface treatment on the shear bond strength of a composite resin to the facial surfac…
2015
Objectives: The present study was conducted to evaluate the optimal method of enhancing the bond strength of a composite resin to the facial surface of the primary anterior stainless steel crowns using various surface treatments namely Nd: YAG laser surface treatment, sandblasting , alloy primer application and no surface treatment. Study Design: The study sample consisted of 60 primary anterior stainless steel crowns (UnitekTM size R 4), with 15 samples randomly divided into the 4 study groups, embedded in acrylic blocks. The facial surface of these surface treated crowns was utilized as the bonding surface to which 2.5mm diameter composite resin cylinders were bonded for the evaluation of…
Surface AFM microscopy of unworn and worn samples of silicone hydrogel contact lenses
2008
Abstract: Purpose. To evaluate the qualitative and quantitative topographic changes in the surface of worn contact lenses (CLs) of different materials using atomic force microscopy (AFM). Methods. The topography of five different CL materials was evaluated withAFM over a surface of 25 lm2 according to previously published experimental setup. Average roughness (Ra) and root mean square (Rms) values were obtained for unworn and worn samples. Results. The Ra value increased for balafilcon A (11.62–13.68 nm for unworn and worn samples, respectively), lotrafilcon A (3.67–15.01 nm for unworn and worn samples, respectively), lotrafilcon B (4.08–8.42 nm for unworn and worn samples, respectively), g…
Towards Laser-Textured Antibacterial Surfaces
2018
AbstractEscherichia coli and Staphylococcus aureus bacterial retention on mirror-polished and ultrashort pulse laser-textured surfaces is quantified with a new approach based on ISO standards for measurement of antibacterial performance. It is shown that both wettability and surface morphology influence antibacterial behavior, with neither superhydrophobicity nor low surface roughness alone sufficient for reducing initial retention of either tested cell type. Surface structures comprising spikes, laser-induced periodic surface structures (LIPSS) and nano-pillars are produced with 1030 nm wavelength 350 fs laser pulses of energy 19.1 μJ, 1.01 μJ and 1.46 μJ, respectively. SEM analysis, optic…
Evaluating the microscopic effect of brushing stone tools as a cleaning procedure
2020
Cleaning stone tool surfaces is a common procedure in lithic studies. The first step widely applied at any archeological site (and/or at field laboratories) is the gross removal of sediment from the surfaces of artifacts. Lithic surface alterations due to mechanical action applied in wet or dry cleaning regimes have never been examined at a microscopic scale. This could have important implications in traceology, as any modern surface modifications inflicted on archeological artifacts might compromise their functional interpretations. The current trend toward quantification of use-wear traces makes the testing even more important, as even slight, apparently invisible surface alterations migh…
Layer-by-layer assembled protein/polymer hybrid films: nanoconstruction via specific recognition
1998
Abstract In the present study it is shown that streptavidin-containing multilayer films with varying numbers of polyelectrolyte spacer layers can be fabricated reproducibly using optimized deposition conditions. Direct alternation of streptavidin and PLB leads to multilayer systems with an average streptavidin thickness of 5.3 nm which is in good agreement with the dimensions of the protein. When the streptavidin layers are spacered by more polyelectrolyte layers the distance between the protein sheets is increased up to e.g. 6.5 nm in the case of (PLB/PSS/PAH/PSS/PLB) as spacer layer. X-ray reflectivity reveals that streptavidin increases the surface roughness of the films probably due to …
Multiscale analyses and characterizations of surface topographies
2018
International audience; This work studies multiscale analyses and characterizations of surface topographies from the engineering and scientific literature with an emphasis on production engineering research and design. It highlights methods that provide strong correlations between topographies and performance or topographies and processes, and methods that can confidently discriminate topographies that were processed or that perform differently. These methods have commonalities in geometric characterizations at certain scales, which are observable with statistics and measurements. It also develops a semantic and theoretical framework and proposes a new system for organizing and designating …