Search results for " Reliability."
showing 10 items of 551 documents
Preliminary magnetic resonance relaxometric analysis of Fricke gel dosimeters produced with polyvinyl alcohol and glutaraldehyde
2017
This work describes the preliminary analysis of Fricke gels dosimeters characterized by a new formulation making use of a matrix of polyvinyl alcohol cross-linked by adding glutaraldehyde and analyzed by means of nuclear magnetic resonance relaxometry. In previous optical studies, these gels have shown promising dosimetric features in terms of photon sensitivity and low diffusion of ferric ions produced after irradiation. In this work, we used a portable nuclear magnetic resonance relaxometer to measure the relaxation times (which are important for dosimetric applications) of these gel materials. For this purpose, we performed a study for optimizing the acquisition parameters with a nuclear…
New applications of zoobenthos measurements for risk assessment of chemicals in aquatic ecosystems
2015
Artikkeliväitöskirja. Yhteenveto-osa ja viisi artikkelia. (Artikkelit eivät avoimesti saatavilla.) Article dissertation. An introduction and five articles (not available in this version). Benthic animals in aquatic ecosystems suffer from various anthropogenic pollutants. A challenge in risk assessment of chemicals in aquatic ecosystems (i.e. ecological risk assessment) has been to balance cost-efficiency and effectiveness in detecting early warning signals of chemicals. In this study, hyperspectral imaging and behavioural measurements were evaluated as novel applications for detecting chemical effects on benthic animals, and the reliability of the incidence of chironomid morphological defor…
Metrological performances of voltage and current instrument transformers in harmonics measurements
2018
In the new electrical system scenario, the increasing presence of non-linear loads and renewable energy sources makes the measurement of harmonics an essential task. The accuracy of harmonic measurement firstly depends on the used instrument transformers for voltage and current sensing. Since the behavior of instrument transformers in non-sinusoidal conditions is not always well defined, this paper presents an experimental study on the metrological performances of current and voltage instrument transformers (CTs and VTs) in the presence of harmonics. Proper tests procedures are defined and measurement setups are developed for both CTs and VTs calibration. The analysis is carried out by usin…
Investigating applicability of ratings of indicators of the CLASS Pre-K instrument
2022
When classroom observations are increasingly used for accountability and evaluation purposes, a deeper understanding of the psychometric properties of such measurement tools is needed. The present study took a unique approach to examine the psychometric properties of a commonly used classroom observation measure by testing the reliability of indicators for higher-order constructs (i.e. dimensions). We investigated the reliability of indicator ratings of the Classroom Assessment Scoring System (CLASS) Pre-K instrument in Finnish kindergarten and first grade classrooms. Twenty-one observer pairs rated 838 segments identified from the 413 lessons of 48 teachers. Variance components models were…
Distribution and generation of traps in SiO2/Al2O3 gate stacks
2007
In this work we combine charge-pumping measurements with positive constant voltage stress to investigate trap generation in SiO2/ Al2O3 n-MOSFET. Trap density has been scanned either in energy or in position based on charge-pumping (CP) measurements performed under different operating conditions in terms of amplitude and frequency of the gate pulse. Our results have revealed that the traps are meanly localized shallow in energy level, deeper in spatial position and they are mostly generated near the Si/SiO2 interface. (C) 2007 Elsevier Ltd. All rights reserved.
On the relationship between occlusion times and in-car glance durations in simulated driving
2023
Drivers have spare visual capacity in driving, and often this capacity is used for engaging in secondary in-car tasks. Previous research has suggested that the spare visual capacity could be estimated with the occlusion method. However, the relationship between drivers’ occlusion times and in-car glance duration preferences has not been sufficiently investigated for granting occlusion times the role of an estimate of spare visual capacity. We conducted a driving simulator experiment (N = 30) and investigated if there is an association between drivers’ occlusion times and in-car glance durations in a given driving scenario. Furthermore, we explored which factors and variables could explain t…
The assessment of the reliability of an innovative 3rd generation solar cell integrated with “thermal belt” glass block
2017
Glass block is a building product widely used for the construction of translucent building façades and roofs. The need to adapt the product to the regulations in the field of energy saving and environmental sustainability has led to the design of innovative configurations, through the integration of different sub-components. These ones are able to improve its energy performance by means of the integration of a“thermal belt”, cold glued to the glass shells, which constitute the traditional glass block, and 3rd generation solar cells. This paper reports the first results of the experimental program designed to assess some durability components: inherent and critical reliability. <div id="g…
Evaluating Safety Systems for Machine Tools with Computer Numerical Control using Analytic Hierarchy Process
2019
Computer numerical control (CNC) machine tools are complex production systems with fully automatic machine parts. Nowadays, high feed rates and machining speeds are used during the machining process. Human operators are still needed to set-up the machine, load/unload workpieces and parts, load the machining code, and supervise the machining process. The operators work in an environment where automated high-speed motions occur, and consequently, CNC machine tools have to be equipped with safety systems. The approach presented in this paper was to evaluate the main safety systems of CNC machine tools based upon the analytic hierarchy process (AHP). The analyzed systems were divided into six m…
Challenges in dental statistics: data and modelling
2022
The aim of this work is to present the reflections and proposals derived from the first Workshop of the SISMEC STATDENT working group on statistical methods and applications in dentistry, held in Ancona (Italy) on 28th September 2011. STATDENT began as a forum of comparison and discussion for statisticians working in the field of dental research in order to suggest new and improve existing biostatistical and clinical epidemiological methods. During the meeting, we dealt with very important topics of statistical methodology for the analysis of dental data, covering the analysis of hierarchically structured and over-dispersed data, the issue of calibration and reproducibility, as well as some…