Search results for " STIR"

NUMERICAL SIMULATION OF SEDIMENT RESUSPENSION IN MECHANICALLY STIRRED VESSEL

2008

Development of a Higee bioreactor (HBR) for production of polyhydroxyalkanoate: Hydrodynamics, gas–liquid mass transfer and fermentation studies

2010

Abstract This study addresses the hydrodynamics and mass transfer characterisation of a Higee bioreactor (HBR) for application to polyhydroxyalkanoate (PHA) production from Pseudomonas putida KT2442 fermentation. The motivation for this work is to address the potential oxygen transfer limitations which can severely impede the progress of this aerobic fermentation process and reduce PHA productivity in conventional bioreactors. It is shown that a maximum of 2.5 transfer units can be achieved in an oxygen-stripping operation where the presence of packing, higher rotor speeds, higher air flowrates and lower liquid flowrates all have a positive influence on the number of transfer units (NTU). W…

VISUALIZATION APPROACHES FOR STIRRED TANK BIOREACTORS

2019

Computational Fluid Dynamics (CFD) is the analysis of fluid behaviour employing numerical solution methods. Using CFD it is possible to analyse simple and complex fluid-gas, fluid-fluid or fluid-solid interactions. Fluid dynamics is described with laws of physics in the form of partial differential equations also known as Navier-Stokes equations. Sophisticated CFD solvers transform these laws into algebraic equations which are solved by numerical methods. In this paper Ansys CFX and Fluent analysis systems as research methods are used to visualize flow patterns in a stirred tank bioreactor. The results obtained are informative and can be used to improve the yield of biomass. CFD analysis ca…

Physico-chemical characterization and corrosion properties of friction stir welded Al2024-T4 alloys

2009

In-process tool force and rotation variation to control sheet thickness change in friction stir welding of magnesium alloys

2016

Two different in-process control strategies, developed in order to produce sound joints in AZ31 magnesium alloy by Friction Stir Welding on sheet blanks with a non-uniform thickness, are presented and compared. To this purpose, sheets with dip or hump were machined and welded by either changing the rotational speed or the tool plunging in order to keep constant the vertical force occurring during welding. The mechanical strength of the joints was measured in the zones where the sheets before welding were characterised by different thicknesses. The sheets welded by the two different strategies are characterized by very similar ultimate tensile strength values. Finally, the results showed tha…

Stimulated Raman adiabatic passage in a $\Lambda$-system in the presence of quantum noise

2011

We exploit a microscopically derived master equation for the study of STIRAP in the presence of decay from the auxiliary level toward the initial and final state, and compare our results with the predictions obtained from a phenomenological model previously used [P. A. Ivanov, N. V. Vitanov, and K. Bergmann, Phys. Rev. A 72, 053412 (2005)]. It is shown that our approach predicts a much higher efficiency. The effects of temperature are also taken into account, proving that in b-STIRAP thermal pumping can increase the efficiency of the population transfer.

Influence of distinct tool pin geometries on aluminum 8090 FSW joint properties

2023

Abstract. Aluminum Lithium alloys are recuperating substantial interest from automotive and aerospace industries owing to their extraordinary specific strength as compared to conventional aluminum (2xxx, 6xxx, and 7xxx) alloys. The goal of the present investigation is to study AA 8090 joints produced with the unique solid-state welding technique friction stir welding (FSW). Tool pin profile induces remarkable influence on friction and further plastic deformation during FSW. Therefrom, the influences of three distinct but constant dynamic area conditioned tool pin geometries namely, square trapezoidal, hexagonal trapezoidal, and threaded taper on the resulting material flow patterns, mechani…

Finite Element Studies On Friction Stir Welding Processes of Tailored Blanks

2008

Although friction stir welding (FSW) has been successfully used to join materials that are difficult-to-weld or unweldable by fusion welding methods, it is still in its early development stage and, therefore, its potential has not been fully exploited yet. FSW appears to be a very promising process for tailor-welded blanks to overcome the difficulties encountered in traditional fusion welding processes for obtaining a sound welding with good nugget integrity. In this paper the friction stir welding process for tailored blanks of aluminum alloy is investigated through a FEM developed by the authors. In particular FSW for sheets with different thicknesses is studied. For each setup a differen…

Influence of material characteristics on plastomechanics of the fsw process for T-joints

2009

Abstract The potential of friction stir welding (FSW) has thoroughly been investigated by several authors, however their focus has primarily been on butt joints. T-joints are of paramount interest for transportation industries especially due to their capacity to straighten panels. Welding of T-joints is very challenging due to thin walls, poor location of the rib–web interface and the requirements for corner-fillets. This paper investigates FSW of T-joints of two popular aluminum alloys, i.e. 2024-T4 and 6082-T6, and the role played by the material characteristics on joining. First, an experimental study is carried out with specially designed fixture to determine the effect of process condi…

Modeling of the Plastic Characteristics of AA6082 for the Friction Stir Welding Process

2015

Focus of this paper is to model the plastic forming behavior of AA6082, in order to develop the numerical FE analysis of the friction stir welding processes and the simulation of subsequent forming processes. During the friction stir welding process, the temperatures reached are until 500 °C and have a fundamental role for the correct performance of the process so the material data has to show a temperature dependency. Because of the tool rotation a strain rate sensitivity of the material has to be respected as well. In this context, the general material characteristics of AA6082 were first identified for different stress states. For the uniaxial state the standard PuD-Al used in the automo…