Search results for " Solar cells"
showing 10 items of 131 documents
Electrical-optical characterization of multijunction solar cells under 2000X concentration
2014
In the framework of the FAE "Fotovoltaico ad Alta Efficienza" ("High Efficiency Photovoltaic") Research Project (PO FESR Sicilia 2007/2013 4.1.1.1), we have performed electrical and optical characterizations of commercial InGaP/InGaAs/Ge triple-junction solar cells (1 cm2) mounted on a prototype HCPV module, installed in Palermo (Italy). This system uses a reflective optics based on rectangular off-axis parabolic mirror with aperture 45×45 cm2 leading to a geometrical concentration ratio of 2025. In this study, we report the I-V curve measured under incident power of about 700 W/m2 resulting in an electrical power at maximum point (PMP) of 41.4 W. We also investigated the optical properties…
Fabrication and Photoelectrochemical Behavior of Ordered CIGS Nanowire Arrays for Application in Solar Cells
2010
In this work, we report some preliminary results concerning the fabrication of quaternary copper, indium, gallium, and selenium CIGS nanowires that were grown inside the channels of an anodic alumina membrane by one-step potentiostatic deposition at different applied potentials and room temperature. A tunable nanowire composition was achieved through a manipulation of the applied potential and electrolyte composition. X-ray diffraction analysis showed that nanowires, whose chemical composition was determined by energy-dispersive spectroscopy analysis, were amorphous. A composition of Cu0.203In0.153Ga0.131Se0.513, very close to the stoichiometric value, was obtained. These nanostructures wer…
Advances in Perovskite Solar Cells.
2015
Organolead halide perovskite materials possess a combination of remarkable optoelectronic properties, such as steep optical absorption edge and high absorption coefficients, long charge carrier diffusion lengths and lifetimes. Taken together with the ability for low temperature preparation, also from solution, perovskite-based devices, especially photovoltaic (PV) cells have been studied intensively, with remarkable progress in performance, over the past few years. The combination of high efficiency, low cost and additional (non-PV) applications provides great potential for commercialization. Performance and applications of perovskite solar cells often correlate with their device structures…
Enhanced efficiency in plastic planar heterojunction solar cells by AuNPs positioned at donor-acceptor interfaces
2018
A new class of copolymers containing oligothiophene moieties with different length and fullerene units have been designed and prepared by an easy and inexpensive one-step synthetic approach. The incorporation of small quantities of these copolymers into bulk heterojunction (BHJ) solar cells with donor regioregular polythiophene (P3HT) and acceptor fullerene derivate (PCBM) results in a good control of the phase separation process without further affecting the BHJ optoelectronic properties. Indeed, these copolymers allow modulating under thermal annealing the growth of domains whose size depends on the length of the copolymer repetitive units. Domain size on the same length scale of the P3HT…
Fluorescence Quenching in Hybrid Solar Cells Based on Electrodeposited ZnO
2013
A study about fluorescence phenomena in hybrid donor-acceptor interfaces based on electrodeposited zinc oxide (e-ZnO) having different architectures is performed. In particular ITO/ZnO/P3HT and ITO/ZnO/P3HT:PCBM are investigated and their photoluminescence responses are compared with those of ITO/P3HT and ITO/P3HT:PCBM. As expected, ITO/ZnO/P3HT:PCBM and ITO/P3HT:PCBM present higher exciton quenching than ITO/ZnO/P3HT and ITO/P3HT respectively. Furthermore, the hybrid configuration ITO/ZnO/P3HT:PCBM displays a higher quenching percentage in a wider wavelength range than ITO/P3HT:PCBM, indicating a better photo-induced charge separation in e-ZnO based hybrid devices.
Integrazione di celle solari di terza generazione nel vetromattone per la realizzazione di pannelli traslucidi fotovoltaici. Analisi prestazione e st…
2013
L’articolo illustra i primi risultati ottenuti nell’ambito dell’analisi prestazionale del vetromattone fotovoltaico, un prodotto edilizio innovativo derivato dall’integrazione di celle fotovoltaiche di terza generazione (DSSC) nel vetromattone, ideato per la realizzazione di involucri traslucidi energeticamente effi cienti ed “attivi”, in grado di ridurre i consumi energetici degli edifi ci e di produrre, al contempo, energia verde. L’analisi è stata condotta su quattro differenti ipotesi di integrazione. Attraverso simulazioni numeriche si è effettuata una valutazione dell’energia assorbita dagli strati attivi oltre che delle prestazioni ottiche complessive del dispositivo. Lo studio anali…
Fabrication and electro-optical characterization of Ruthenium-based Dye-Sensitized Solar Cells
2015
In this paper, we measure the main photoelectrical parameters of Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes at different irradiance levels, incident wavelengths, temperatures and hours of light soaking
Experimental characterization of Ruthenium-based Dye Sensitized Solar Cells and study of light-soaking effect impact on performance
2016
In this paper, we present an experimental investigation on the performance of Ruthenium-based Dye Sensitized Solar Cells (DSSCs) at different irradiance levels, incident wavelengths and hours of illumination. In particular, the measurements have been aimed at studying the performance variation due to light soaking effect since this phenomenon has noteworthy practical implications, such as stability tests of DSSCs. Our results show that the short circuit current density, the open circuit voltage and the conversion efficiency η increase with the hours of light soaking. Finally, the observed phenomenon is reversible, and thus the performance decreases again when the cell is kept in the dark.
Colloidal Self-assembled Nanosphere Arrays for Plasmon-enhanced Light Trapping in Thin Film Silicon Solar Cells
2014
To realize high-efficiency thin-film silicon solar cells it is crucial to develop light-trapping methods that can increase absorption of the near- bandgap light in the silicon material. That can be achieved using the far-field scattering properties of metal nanoparticles (MNP) sustaining surface plasmons. The MNPs should be inserted in the back of the cell, embedded in the transparent conductive oxide (TCO) layer which separates the rear mirror from the silicon layers. In this way, a plasmonic back reflector (PBR) is constructed that can redirect light at angles away from the incidence direction and thereby increase its path length in the cell material. In this work, a novel technique is pr…
Graded Carrier Concentration Absorber Profile for High Efficiency CIGS Solar Cells
2015
We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters-characteristic of such devices-with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depe…