Search results for " Steel"
showing 10 items of 244 documents
Inhibition of Cor-Ten steel corrosion by “green” extracts of Brassica campestris
2018
Abstract Extract of Brassica campestris was tested as potential corrosion inhibitor for Cor-Ten steel in NaCl and acidic solutions, simulating a marine and an urban-industrial environment, respectively. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) were performed both in absence and in presence of the extract at room temperature. The surface chemical analysis was investigated by X-ray Photoemission Spectroscopy (XPS), before and after corrosion. Electrochemical results demonstrated that a very small concentration of Brassica campestris extracts can inhibit Cor-Ten corrosion in NaCl solution (inhibition efficiency of 80–84%) better than in acidic solutions. Su…
Simplified Model for Compressive Behavior of Concrete Columns Strengthened by Steel Angles and Strips
2010
This paper presents an analytical model to determine the compressive response of concrete members, having a square transverse cross section and reinforced with steel angles at the corners and steel strips connecting the steel angles. The model evaluates the effects of transverse strips and steel angles on confinement pressures, including strength and buckling phenomena. Compressive response was evaluated in cases of directly and indirectly loaded elements. The data produced correlate well with available experimental data.
The combined influence of grain size distribution and dislocation density on hardness of interstitial free steel
2020
Abstract Understanding the relationship between microstructure features and mechanical properties is of great significance for the improvement and specific adjustment of steel properties. The relationship between mean grain size and yield strength is established by the well-known Hall-Petch equation. But due to the complexity of the grain configuration within materials, considering only the mean value is unlikely to give a complete representation of the mechanical behavior. The classical Taylor equation is often used to account for the effect of dislocation density, but not thoroughly tested in combination with grain size influence. In the present study, systematic heat treatment routes and…
Photoelectrochemical and XPS characterisation of oxide layers on 316L stainless steel grown in high-temperature water
2015
Passive films on AISI 316L stainless steel were grown by exposure in high temperature (300 °C and 150 bar) water. X-ray photoelectron spectroscopy was employed to study their composition as a function of immersion time. A photoelectrochemical investigation, supported by electrochemical and impedance measurements, allowed to get information on the solid-state properties of the investigated layers. The experimental results suggest the formation of a stratified layer with an outer iron-rich layer and an inner Cr-rich oxide layer, whose relative thickness and composition are dependent on the immersion time.
Influence of the microstructure on the corrosion behaviour of low-carbon martensitic stainless steel after tempering treatment
2014
Abstract The microstructure of grade X4CrNiMo16.5.1 stainless steel was studied at different scales. The chemical composition of the native passive film formed on the different phases was then determined at the microscale. The degree of homogeneity of the native passive film is discussed. Subsequently, the susceptibility to pitting corrosion of X4CrNiMo16.5.1 was quantified using the electrochemical microcell technique. The nature of precursor sites and the morphology of pits were investigated by combining scanning electron microscopy with Electron BackScatter Diffraction and potentiostatic pulse tests. The role of the microstructure and the cold-worked layer generated by polishing in pitti…
Influence of reactive element oxide coatings on the high temperature cyclic oxidation of chromia-forming steels
2003
Abstract The beneficial effects of reactive element oxide coatings, Y2O3, Nd2O3 and Yb2O3, on the cyclic oxidation behaviour of a Fe–30Cr model alloy, were studied at 950 °C in air under atmospheric pressure. The oxide scale grown on uncoated samples started to spall after 2 cycles, because of its poor adherence. The coated specimens remarkably resisted to the thermal shocks, since no oxide scale spallation or cracks could be observed, even after 1000 h of cycling experiments. The surface oxide scale consisted of facetted oxide grains on the uncoated samples. On the contrary, it exhibited a fine-grained structure on the coated specimens. The reactive element beneficial effect was ascribed t…
Analytical prediction of the shear connection capacity in composite steel–concrete trussed beams
2016
Steel–concrete trussed composite beams are a particular types of composite girders constituted by a steel truss embedded in a concrete core. The truss is typically composed by a steel plate or a precast concrete slab working as bottom chord while coupled rebars are generally used to form the upper chord. Moreover, a system of ribbed or smooth steel rebars welded to the plate and forming the diagonals of the truss, works as web reinforcement. In the present study, the attention is focused on the evaluation of the shear resistance of the connection between bottom steel plate (the bottom chord) and concrete core through the diagonal bars of the truss developing a mechanical model able to accou…
Friction and wear of lubricated M3 Class 2 sintered high speed steel with and without TiC and MnS additives
2005
Abstract M3/2 sintered high speed steel and composite materials processed by initial admixing of 5 wt.% TiC (to decrease wear) and 5 wt.% MnS (to minimise friction) powders, singly and in combination, were assessed in pin-on-disc tribometers specially constructed to simulate use in the automotive valve train. Pins were of the sintered materials and the mating tribological material discs of T1 high speed steel. For comparison with existing conventional materials, identical tests were performed with discs and pins of two types of spheroidal cast iron. Testing at ∼110 °C, employing a few drops of fresh Shell Helix Standard SAE: 15W-40, API: SJ/CF oil, in daily segments of 5000 m of sliding dis…
Friction Stir Welding of steels process design through a continuum based fem model
2009
AbstractFriction stir welding (FSW) has been reaching a continuously increasing popularity among joining processes since its invention in 1991. Although mainly used for aluminium alloys, it has been successfully applied also to steels. In the present paper, a continuum based FEM model for FSW of steels is proposed, which is three-dimensional Lagrangian implicit, coupled, rigid viscoplastic. The model, whose potential has been analysed through temperature distribution comparisons, is able to predict temperature, strain and strain rate distributions, together with thermal and mechanical loads on the welding tool, at varying main process variables. In this way, the FEM model can be used for pr…
Electropolishing of CuZn brasses and 316L stainless steels: Influence of alloy composition or preparation process (ALM vs. standard method)
2016
International audience; In the present paper, electropolishing behavior of different brass alloys (CuZn39Pb2, CuZn42) in phosphoric acid is studied to observe the impact of alloying elements on polishing quality. In the same way, the influence of the manufacturing process is also evaluated through the comparison of a “standard” stainless steel and a stainless steel prepared by Additive Laser Manufacturing (ALM). An electrochemical study was first performed to determine the best treatment conditions for each material/electrolyte pair and to study the electropolishing mechanism and its kinetic dependence on diffusion. Metallic samples are fully characterized before and after electropolishing …