Search results for " Stresses"

Instabilities Effects in Thin Film Solar Cells: Reversible Ageing, Performance Recovery and Improvement by Electrical Stresses

Solitary Waves for the Assessment of Thermal Stress and Neutral Temperature in Slender Structures

2015

Slender columns and continuous welded rails subjected to compressive stress are common in many civil structures. The rapid in-situ measurement of this stress may be of interest to prevent structural anomalies such as buckling. In this article, the authors describe the coupling mechanism between highly nonlinear solitary waves (HNSWs) propagating along an L-shaped granular system and a beam in contact with the granular medium. The aim is the evaluation of HNSWs as a tool to measure stress in thermally loaded structures and to estimate the neutral temperature, i.e. the temperature at which this stress is null. The authors investigated numerically and experimentally one chain of spherical part…

An Experimental Investigation of Residual Stresses in Hard Machining of AISI 52100 Steel

2011

In this paper an experimental investigation was conducted to determine the effects of the tool cutting-edge geometry, workpiece hardness, cutting speed, and microstructural changes (white and dark layers) on the residual stresses in dry orthogonal hard machining of AISI 52100 steel. X-ray diffraction technique was used to obtain in-depth residual stresses profiles in both axial and circumferential directions. The results show that tool geometry, workpiece hardness and cutting parameters significantly affect the surface residual stress, maximum compressive residual stress below the machined surface and its location. Moreover, microstructural analysis shows that thermally-induced phase transf…

Inverting Multiple Residual Stress Components from Multiple Cuts with the Contour Method

2007

An extension of the contour method is presented which allows the measurement of multiple stress components by making multiple cuts. In the contour method, a body is carefully cut in two using wire electric discharge machining (EDM). The contours, or shapes, of the cut surfaces are then measured and used to calculate the original residual stress normal to the cut plane using a simple finite element calculation. In the extension presented here, the two pieces from the original body can be cut again in a transverse direction, and the contours of the new cut surfaces are measured. The stresses calculated on the planes of these second cuts have been affected by the first cut. Then a simple inver…

Residual strain effects on the two-dimensional electron gas concentration of AlGaN/GaN heterostructures

2001

Ga-face AlGaN/GaN heterostructures with different sheet carrier concentrations have been studied by photoluminescence and Raman spectroscopy. Compared to bulk GaN, an energy shift of the excitonic emission lines towards higher energies was observed, indicating the presence of residual compressive strain in the GaN layer. This strain was confirmed by the shift of the E2 Raman line, from which biaxial compressive stresses ranging between 0.34 and 1.7 GPa were deduced. The spontaneous and piezoelectric polarizations for each layer of the heterostructures have been also calculated. The analysis of these quantities clarified the influence of the residual stress on the sheet electron concentratio…

Residual stresses in friction stir welding: numerical simulation and experimental verification

2008

A New Procedure for the Evaluation of Non-Uniform Residual Stresses by the Hole Drilling Method Based on the Newton-Raphson Technique

2010

The hole drilling method is one of the most used semi-destructive techniques for the analysis of residual stresses in mechanical components. The non-uniform stresses are evaluated by solving an integral equation in which the strains relieved by drilling a hole are introduced. In this paper a new calculation procedure, based on the Newton-Raphson method for the determination of zeroes of functions, is presented. This technique allows the user to introduce complex and effective forms of stress functions for the solution of the problem. All the relationships needed for the evaluation of the stresses are obtained in explicit form, eliminating the need to use additional mathematical tools. The t…

An analysis of through-thickness residual stresses in aluminium FSW butt joints

2006

Abstract In the paper, the results of a wide experimental campaign on friction stir welding (FSW) of aluminum alloys are reported. The attention was focused on the through-thickness residual stresses that occur on aluminum joints, after the welding process. In detail, using the hole-drilling method the residual stresses distribution in the zone close to the tool shoulder border of the joint advancing side, has been investigated; four different aluminum alloys and three different process conditions have been considered. The experimental analysis has shown that unlike traditional welding processes, the residual stresses are negative in the surface of the examined zone, and increase with depth…

Residual Stresses in Glasses

2013

The history dependence of the glasses formed from flow-melted steady states by a sudden cessation of the shear rate $\dot\gamma$ is studied in colloidal suspensions, by molecular dynamics simulations, and mode-coupling theory. In an ideal glass, stresses relax only partially, leaving behind a finite persistent residual stress. For intermediate times, relaxation curves scale as a function of $\dot\gamma t$, even though no flow is present. The macroscopic stress evolution is connected to a length scale of residual liquefaction displayed by microscopic mean-squared displacements. The theory describes this history dependence of glasses sharing the same thermodynamic state variables, but differi…

Magneto-Electro-Elastic Bimorph Analysis by the Boundary Element Method

2008

The influence of the magnetic configuration on the behavior of magneto-electro-elastic bimorph beams is analyzed by using a boundary element approach. The problem is formulated by using the generalized displacements and generalized tractions. The boundary integral equation formulation is obtained by extending the reciprocity theorem to magneto-electro-elastic problems; it is numerically implemented by using the boundary element method multidomain technique to address problems involving nonhomogeneous configurations. Results under different magnetic configurations are compared highlighting the characteristic features of magnetopiezoelectric behavior particularly focusing on the link between …