Search results for " electronics"
showing 10 items of 580 documents
Analyses of the OSU-MASLWR Experimental Test Facility
2012
Today, considering the sustainability of the nuclear technology in the energy mix policy of developing and developed countries, the international community starts the development of new advanced reactor designs. In this framework, Oregon State University (OSU) has constructed, a system level test facility to examine natural circulation phenomena of importance to multi-application small light water reactor (MASLWR) design, a small modular pressurized water reactor (PWR), relying on natural circulation during both steady-state and transient operation. The target of this paper is to give a review of the main characteristics of the experimental facility, to analyse the main phenomena characteri…
Low-Power Design of Delay Interpolating VCO
2008
In this paper, a design methodology for low-power MCML based delay interpolating VCOs is presented. The methodology allows a fast and accurate graphical evaluation of the optimum design. It utilizes two closed form expressions for the upper and lower oscillation frequencies of the VCO. An expression of the tuning range is also derived. The effectiveness of the proposed design methodology has been tested by simulating several VCOs in an IBM 0.13 mum CMOS technology.
A photovoltaic system suitable for the battery pack charging of an electrically power assisted velocipede
2012
The paper describes the designing, sizing, realization and setting up of a complete system suitable for the management of an electrically power assisted velocipede using a photovoltaic module for the charging of the batteries. In the work an overview on the sustainable mobility needs and on the commercial electrically power assisted velocipedes is presented and the "Ecolapa" prototype, set up in the SDELab laboratory of Palermo University, is precisely described underlining the designing, implementation and setting up phases of the photovoltaic charging system settled up on the velocipede. Moreover tests oriented on the setting up of the whole system and validation tests on the prototype ar…
Numerical Analysis of Medium Scale PV Plants and Their Power-Flow Control System With a Simple Three Phase Inverter
2012
This paper presents a mathematical analysis of a medium scale Photovoltaic (PV) power generation system connected to the distribution network and of its control system, in which the conversion stage is unique thanks to the absence of a boost chopper. Boost choppers are usually used as actuator for maximum power point tracking (MPPT). The conducted analysis leads to the conclusion that the used inverter presents two degrees of freedom that can be easily exploited in a control system in which the inverter simultaneously realizes the interconnection to the grid and at the same time realizes the MPPT control. The structure of the control system is then presented, discussed and then validated by…
Identification and robust control of DC/DC converter Hammerstein model
2008
Abstract—This paper deals with model-based robust control of dc/dc power electronic converters. The converter is described by means of a Hammerstein model consisting of the nonlinear static characteristics of the converter and a linear time-invariant (LTI) uncertainmodel whose parameters depend on the actual duty-cycle operating range. This suggests that the controller be designed using robust control techniques. In view of applying robust control, identification of the earlier LTI models is performed by means of simulation experiments, carried out on a converter switching model implemented onMATLAB/SIMULINK environment. Internal model control (IMC) structure is employed for the controller …
Analysis of driving cycles effects on power supply requirements of a fuel cell powered light-weight electric vehicle
2015
In this paper, fuel cell powered lightweight vehicles are addressed. A MATLAB/Simulink simulation model including motor, electrical drive, the fuel cell and power electronics systems is implemented. The model is well suited to perform the driving cycle test, which reproduces the speed pattern of an electric vehicle through urban, rural or motorway routes. This paper aims at investigating the most suited driving cycle to design high performances hybrid power supply for electric vehicles in terms of cruising range, cost and size of the power supply equipment. For this purpose, a legislative and a real-world driving cycles are selected. Effects of driving cycles on the power system requirement…
A General Mathematical Model for non-Redundant Fault-Tolerant Inverters
2011
Industrial systems able to release trusted services is an integrated concept that resumes the attributes of availability, reliability, safety, integrity, and maintainability. In power electronics this can be aimed via the introduction of fault tolerant architectures. While In the past technical literature the mathematical modeling problem for non-redundant converters was fronted studying separately the cases of fault leg by leg, in this paper a general model able to include the three possible cases of leg faults with a unique set of equation is introduced and discussed. The same model allows to evaluate the DC Link transient and steady state evolution and also allows to develop with much ea…
Towards roll-to-roll fabrication of electronics, optics and optoelectronics for smart and intelligent packaging
2004
Embedding of optoelectrical, optical, and electrical functionalities into low-cost products like packages and printed matter can be used to increase their information content. These functionalities make also possible the realization of new type of entertaining, impressive or guiding effects on the product packages and printed matter. For these purposes, components like displays, photodetectors, light sources, solar cells, battery elements, diffractive optical elements, lightguides, electrical conductors, resistors, transistors, switching elements etc. and their integration to functional modules are required. Additionally, the price of the components for low-end products has to be in cent sc…
A Technique for Power Supply Harmonic Impedance Estimation Using a Controlled Voltage Disturbance
2002
A method for power system impedance estimation is presented. The method employs a power converter to inject a voltage transient onto the supply system. As the technique employs controlled power electronic devices it may be used as a stand alone piece of a portable measurement equipment, or it may be embedded into the functions of an active shunt filter for improved harmonic control. The impedance is estimated through correlation of the measured voltage and current transients. Simulations and experimental results demonstrate the measurement technique is highly accurate and effective.
Novel Resistance Measurement Method: Analysis of Accuracy and Thermal Dependence with Applications in Fiber Materials
2016
Material resistance is important since different physicochemical properties can be extracted from it. This work describes a novel resistance measurement method valid for a wide range of resistance values up to 100 GΩ at a low powered, small sized, digitally controlled and wireless communicated device. The analog and digital circuits of the design are described, analysing the main error sources affecting the accuracy. Accuracy and extended uncertainty are obtained for a pattern decade box, showing a maximum of 1 % accuracy for temperatures below 30 ∘ C in the range from 1 MΩ to 100 GΩ. Thermal analysis showed stability up to 50 ∘ C for values below 10 GΩ and systematic deviations for higher …