Search results for " electronics"
showing 10 items of 580 documents
Compatibilization of Polypropylene/Polyamide 6 Blend Fibers Using Photo-Oxidized Polypropylene.
2018
The use of polyamide/polyolefin blends has gained importance and concern for years, but they also show some issues to be adequately addressed, such as the incompatibility between the two components. This is usually overcome by using suitable compatibilizers, typically based on functionalized polyolefins. However, there is only little information about the use of a degraded polyolefins to induce compatibilization. This is even truer, as far as polyamide 6/polypropylene (PA6/PP) blends are concerned. In this work, compatibilization of PA6/PP blends by using small amounts of photo-oxidized PP was investigated
Reactive Powder Concrete Containing Basalt Fibers: Strength, Abrasion and Porosity
2020
The paper presents the test results of basalt fiber impact on a compressive and flexural strength, resistance to abrasion and porosity of Reactive Powder Concrete (RPC). The reasons for testing were interesting mechanical properties of basalt fibers, the significant tensile strength and flexural strength, and in particular the resistance to high temperatures, as well as a relatively small number of RPC tests performed with those fibers and different opinions regarding the impact of those fibers on concrete strength. The composition of the concrete mix was optimized to obtain the highest packing density of particles in the composite, based on the optimum particle size distribution curve acc.…
Tantalum nitride thin film resistors by low temperature reactive sputtering for plastic electronics
2008
This article describes the fabrication and characterisation of tantalum nitride (TaN) thin film for applications in plastic electronics. Thin films of comparable thickness (50-60 nm) have been deposited by RF-magnetron-reactive sputtering at low temperature (100 °C) and their structure and physical (electrical and mechanical) properties have been correlated by using sheet resistance, stress measurements, atomic force microscopy (AFM), XPS, and SIMS. Different film compositions have been obtained by varying the argon to nitrogen flow ratio in the sputtering chamber. XPS showed that 5:1, 2:1 and 1:1 Ar:N 2 ratios gives Ta 2 N, TaN and Ta 3 N 5 phases, respectively. Sheet resistance revealed a…
Detection of Partial Discharges at Square Shaped Voltages
2018
Due to the wide use of electronic converters and the introduction of new powerful power electronics devices, the input waveforms most often used are becoming much different than the traditional power frequent sinusoidal one. In High Voltage (HV) apparatus particularly, this condition can increase the stress on the insulation systems that may lower the reliability of the whole power grid. This type of input voltage, often showing an increased voltage gradient, causes problems in the Partial Discharge (PD) measurement setup and acquisition systems, also due to the increased harmonic content. In this paper, the main aim is to discuss how to suitably approach the measurement technique of PDs at…
A fast heuristic for solving the D1EC coloring problem
2010
In this paper we propose an efficient heuristic for solving the Distance-1 Edge Coloring problem (D1EC) for the on-the-fly assignment of orthogonal wireless channels in wireless as soon as a topology change occurs. The coloring algorithm exploits the simulated annealing paradigm, i.e., a generalization of Monte Carlo methods for solving combinatorial problems. We show that the simulated annealing-based coloring converges fast to a sub optimal coloring scheme even for the case of dynamic channel allocation. However, a stateful implementation of the D1EC scheme is needed in order to speed-up the network coloring upon topology changes. In fact, a stateful D1EC reduces the algorithm’s convergen…
Frequency constrained optimal Power Flow based on Glow-worm Swarm Optimization in Islanded Microgrids
2015
This work presents an application of a swarm optimization method to solve the optimal power flow problem taking into account the constraints of frequency and line ampacity in three-phase islanded Microgrids. Each generation unit is equipped with a Power Electronics Interface. In the considered formulation, the droop control parameters are considered as variables to be adjusted by a higher control level, while the frequency is kept in rated bounds. Another typical constraint for OPF formulation, the max ampacity of each line, is also considered. Two case studies with different dimensions and electrical features have been considered and the obtained results show the efficiency of the proposed…
On Randomness and Structure in Euclidean TSP Instances: A Study With Heuristic Methods
2021
Prediction of the quality of the result provided by a specific solving method is an important factor when choosing how to solve a given problem. The more accurate the prediction, the more appropriate the decision on what to choose when several solving applications are available. In this article, we study the impact of the structure of a Traveling Salesman Problem instance on the quality of the solution when using two representative heuristics: the population-based Ant Colony Optimization (ACO) and the local search Lin-Kernighan (LK) algorithm. The quality of the result for a solving method is measured by the computation accuracy, which is expressed using the percent error between its soluti…
Bioactivity of bioceramic materials used in the dentin-pulp complex therapy : a systematic review
2019
Este es el artículo que se ha publicado de forma definitiva en: https://www.mdpi.com/1996-1944/12/7/1015 Dentistry-applied bioceramic materials are ceramic materials that are categorized asbioinert, bioactive and biodegradable. They share a common characteristic of being specificallydesigned to fulfil their function; they are able to act as root canal sealers, cements, root repair or fillingmaterials. Bioactivity is only attributed to those materials which are capable of inducing a desiredtissue response from the host. The aim of this study is to present a systematic review of availableliterature investigating bioactivity of dentistry-applied bioceramic materials towards dental pulp stemcel…
The gold-sulfur interface at the nanoscale.
2012
Thiolate-protected gold surfaces and interfaces, relevant for self-assembled monolayers of organic molecules on gold, for passivated gold nanoclusters and for molecule-gold junctions, are archetypal systems in various fields of current nanoscience research, materials science, inorganic chemistry and surface science. Understanding this interface at the nanometre scale is essential for a wide range of potential applications for site-specific bioconjugate labelling and sensing, drug delivery and medical therapy, functionalization of gold surfaces for sensing, molecular recognition and molecular electronics, and gold nanoparticle catalysis. During the past five years, considerable experimental …
Dynamic and electronic transport properties of DNA translocation through graphene nanopores
2013
Graphene layers have been targeted in the last years as excellent host materials for sensing a remarkable variety of gases and molecules. Such sensing abilities can also benefit other important scientific fields such as medicine and biology. This has automatically led scientists to probe graphene as a potential platform for sequencing DNA strands. In this work, we use robust numerical tools to model the dynamic and electronic properties of molecular sensor devices composed of a graphene nanopore through which DNA molecules are driven by external electric fields. We performed molecular dynamic simulations to determine the relation between the intensity of the electric field and the transloca…