Search results for " fuel cell."
showing 10 items of 166 documents
Double cross-linked polyetheretherketone proton exchange membrane for fuel cell
2012
Abstract The proton exchange membrane based on polyetheretherketone was prepared via two steps of cross-linking. The properties of the double cross-linked membrane (water uptake, proton conductivity, methanol permeability and thermal stability) have been investigated for fuel cell applications. The prepared membrane exhibited relatively high proton conductivity, 3.2 × 10 −2 S cm −1 at room temperature and 5.8 × 10 −2 S cm −1 at 80 °C. The second cross-linking significantly decreased the water uptake of the membrane. The performance of direct methanol fuel cell was slightly improved as compared to Nafion ® 117 due to its low methanol permeability. The results indicated that the double cros…
First-principles modelling of complex perovskite (Ba1-xSrx)(Co1-yFey)O3-δ for solid oxide fuel cell and gas separation membrane applications
2010
The results of the first principles spin-polarized DFT calculations of the atomic and electronic structure of a complex perovskite (Ba1-xSrx)(Co1-yFey)O3-δ (BSCF) used as a cathode material for solid oxide fuel cells (SOFC) and gas separation membranes are presented and discussed. The formation energies of oxygen vacancies are found to be considerably smaller than in other magnetic perovskites, e.g. (La,Sr)MnO3, which explains the experimentally observed strong deviation of this material from stoichiometry. The presence of oxygen vacancies induces a local charge redistribution, associated with the local lattice perturbation, and expansion of the equilibrium volume, in line with the experime…
Advances in Anodic Alumina Membranes-based fuel cell: CsH2PO4 pore-filler as proton conductor at room temperature
2009
Abstract Anodic alumina membranes (AAM) filled with cesium hydrogen phosphate proton conductor have been tested as inorganic composite electrolyte for hydrogen–oxygen thin film (≤50 μm) fuel cell (TFFC) working at low temperatures (25 °C), low humidity ( T gas = 25 °C) and low Pt loading (1 mg cm −2 ). Single module TFFC delivering a peak power of around 15–27 mW cm −2 , with open circuit voltage (OCV) of about 0.9 V and short circuit current density in the range 80–160 mA cm −2 have been fabricated. At variance with pure solid acid electrolytes showing reproducibility problems due to the scarce mechanical resistance, the presence of porous alumina support allowed to replicate similar fuel…
Methanol and proton transport through chitosan-phosphotungstic acid membranes for direct methanol fuel cell
2020
Composite chitosan-phosphotungstic acid membranes were synthesized by ionotropic gelation. Their liquid uptake is higher for thin membranes (23 ± 2 μm), while it is lower (~70%) for thicker membranes (50-70 μm). Polarization curves recorded using single module fuel cell at 70°C allowed to estimate a peak power density of 60 mW cm−2 by using 1 M as methanol and low Pt and Pt/Ru loadings (0.5 and 3 mg cm−2) at the cathode and at the anode, respectively. Electrochemical impedance spectroscopy was used to estimate the membrane conductivity and to model the electrochemical behavior of methanol electrooxidation inside the fuel cell revealing a two-step mechanism mainly responsible of overall kine…
Cross-linked PEEK-WC proton exchange membrane for fuel cell
2009
Abstract The low cost proton exchange membrane was prepared by cross-linking water soluble sulfonated-sulfinated poly(oxa- p -phenylene-3,3-phthalido- p -phenylene-oxa- p -phenylene-oxy-phenylene) (SsPEEK-WC). The prepared cross-linked membrane became insoluble in water, and exhibited high proton conductivity, 2.9 × 10 −2 S/cm at room temperature. The proton conductivity was comparable with that of Nafion ® 117 membrane (6.2 × 10 −2 S/cm). The methanol permeability of the cross-linked membrane was 1.6 × 10 −7 cm 2 /s, much lower than that of Nafion ® 117 membrane.
Covalent-ionically cross-linked polyetheretherketone proton exchange membrane for direct methanol fuel cell
2010
Abstract In this paper, the proton exchange membrane prepared by covalent-ionically cross-linking water soluble sulfonated–sulfinated poly(oxa- p -phenylene-3,3-phthalido- p -phenylene-oxa- p -phenylene-oxy-phenylene) (SsPEEK-WC) is reported. Compared with covalent cross-linked PEEK-WC membrane, this covalent-ionically cross-linked PEEK-WC membrane exhibits extremely reduced water uptake and methanol permeability, but just slightly sacrificed proton conductivity. The proton conductivity of the covalent-ionically cross-linked PEEK-WC membrane reaches to 2.1 × 10 −2 S cm −1 at room temperature and 4.1 × 10 −2 S cm −1 at 80 °C. The methanol permeability is 1.3 × 10 −7 cm 2 s −1 , 10 times …
Grid interaction and environmental impact of a net zero energy building
2020
Abstract The concept of Net Zero Energy Building (NZEB), as a grid-connected building that generates as much energy as it uses over a given period, has been developing through policies and research agendas during the last decade as a contribution towards the decarbonization of the building sector. However, since the most applicable and widely used renewable energy supply options are non-programmable, the large-scale NZEBs diffusion into the existing power grids can seriously affect their stability having a relapse on operation costs and environmental impacts. In this context, the study aims at performing the design of the energy systems to be used in the case-study through a wide numbers of…
Fuel cell modelling and test: Experimental validation of model accuracy
2013
In the last few years, renewable energies have been encouraged by worldwide governments to meet energy saving policies. Among renewable energy sources, fuel cells have attracted much interest for a wide variety of research areas. Fuel cell-based residential-scaled power supply systems take advantage of simultaneous generation of power and heat, reducing the overall fossil fuel consumption and utilities cost. Modeling is one of the most important topics concerning fuel cell use. In this paper, a measurement-based steady-state and dynamic fuel cell model is presented. The proposed modelling approach is implemented on a 5kW Proton Exchange Membrane Fuel Cell. The parameters identification proc…
MATLAB-based simulator of a 5 kW fuel cell for power electronics design
2013
Abstract In the last few years, renewable energies have been encouraged by worldwide governments to meet energy saving policies. Among renewable energy sources, fuel cells have attracted much interest for a wide variety of research areas. Since combined heat-power generation is allowed, household appliances are still the most promising applications. Fuel cell-based residential-scaled power supply systems take advantage by simultaneous generation of power and heat, reducing the overall fossil fuel consumption and utilities cost. Modelling is one of the most important topic concerning fuel cell use. In this paper, a measurement-based steady-state and dynamic fuel cell model is presented. The …
Development of electrodes materials for SOFC fed by natural gas / biogas. Applications to "pre-reforming" and "single-chamber" concepts
2010
Solid Oxide Fuel Cell is a device for “clean” electricity production from chemical energy. The new configuration called “single-chamber” seems to be very attractive with several advantages over bi-chamber conventional configuration: easier manufacturing, lowering of working temperature, possible use of hydrocarbons as fuel… Such configuration involves the development of new electrode materials satisfying new requirements. The evaluation of 7 potential cathode materials through several characterizations has shown that a compromise has to be found since one material does not exhibit all the requested features. A library of 15 supported catalysts (3 metals and 5 supports) was developed. These …